Marantec Command 231 Manual

Marantec Garageportåbner Command 231

Læs gratis den danske manual til Marantec Command 231 (2 sider) i kategorien Garageportåbner. Denne vejledning er vurderet som hjælpsom af 70 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 35.5 anmeldelser. Har du et spørgsmål om Marantec Command 231, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Command 231

Radio code keypad for impulse control

Version

Command 231 868 MHz (Art.-No. 68 328)

Command 231 433 MHz (Art.-No. 68 333)

Safety advice

Attention:

• Please read these instructions carefully

before connecting and operating this

device!

• Have faulty and defective devices checked

by the manufacturer.

• You are not authorized to carry out

changes to this device.

Function

The radio code keypad offers you the possibility to

open and close your garage door by entering a

4-digit personal identification number (PIN). It can

be programmed, so that up to 3 garage door

operators can be actuated with a different code

each or one garage door operator can be actuated

with up to three different PIN's. Additionally any

number can be programmed temporarily as PIN in

order to grant a temporary access for certain visitors

or service personnel.

Beside this an additional device (e.g. the yard light)

can be controlled. For this function ("light function")

a further receiver is required.

Installation of the radio code keypad

• Choose a suitable place to install the radio code

keypad.

• Take the wall bracket as pattern and mark the

place for the two drill holes. Then drill the holes

and insert the enclosed wall plugs.

• Screw on the wall bracket by means of the

enclosed screws. For surfaces other than wood

other screws and wall plugs may be necessary.

• Click the radio code keypad into the wall bracket.

• Take a coin to turn the lock on the bottom side of

the wall bracket clockwise to fix the radio code

keypad.

Enter PIN and transmit code

Your radio code keypad is delivered with

1 random code and 1 PIN already programmed.

The factory programmed PIN is 1-2-3-4.

Attention:

To program the third code the preset

code (random programming) must be

overwritten with the PIN 1-2-3-4 and

then the PIN 1-2-3-4 must be changed

according to the instructions.

In case you already use another radio transmitter to

control your garage door operator, the code of this

has to be transmitted from the transmitter to the

actual radio code keypad.

Transmit the code for the garage door control

from one transmitter to the radio code keypad:

• Connect the radio code keypad and the actual

transmitter by means of the programming plug.

• Hold the button on the transmitter you control

the garage door with.

Press the ENTER button on the radio code keypad.

The keypad lights up.

• Enter a new 4-digit PIN of your choice. Then press

the ENTER button again. Hold the transmitter

button until the LED on the radio code keypad

flashes quickly.

• Now the radio code keypad has learned the

transmitter code and saved under the PIN you

have entered. Now you may remove the

programming plug.

Transmit the code for light function from one

transmitter to the radio code keypad:

The light function is already programmed with a

special code. But you may as well transmit another

transmitter code to actuate the light function.

• Connect the radio code keypad and the actual

transmitter by means of the programming plug.

• Hold the specific button on the transmitter you

activate the other device with. Press the ENTER

button on the radio code keypad. The keypad

lights up.

• Press the LIGHT button and then again the ENTER

button. Hold the transmitter button until the LED

on the radio code keypad flashes quickly.

• The radio code keypad has now learned the new

transmitter code for the light function. Now you

may remove the programming plug.

Save more than 1 code to control more than

1 garage door operator:

• With the radio code keypad you may control up

to 3 different garage door operators, each with a

different code.

• For each of the 3 codes proceed as described

above, but with one exception: You must enter a

different PIN for each code, which means each

code requires an individual PIN.

• To open or close a certain garage door with the

radio code keypad, just enter the respective PIN

and then press the ENTER button.

Save more than 1 PIN for the same code:

Beside the already programmed PIN it is possible to

save up to 2 additional PIN's for the same code and

to assign these PIN's to different persons.

• Follow the instructions described under "Transmit

the code for the garage door control from one

transmitter to the radio code keypad" for every

single PIN. Repeat these steps for each PIN with

the same transmitter. So the same code is saved

under 3 different PIN's.

Save a temporary PIN:

A temporary PIN that is valid only for three actuations

can be saved.

• Hold "button 1" for 3 sec. until the LED flashes

quickly. Enter the currently valid PIN and then

press the ENTER button.

• Enter a temporary 4-digit PIN of your choice and

then press the ENTER button.

• The LED glows up for 2 sec. Then the keypad light

goes off. The radio code keypad is ready for

operation again.

• To use the radio code keypad with the latest

temporary PIN enter the 4-digit temporary PIN and

then press the ENTER button. You are allowed to

use this PIN three times and then it is automatically

cleared.

iverSender

P rstecker

Steckerbuchse

Cover

Keypad light

Socket

Programming plug

Active

transmitter

Mounting holes

Screws

Lock

Coin

Wall bracket

Wall

plug

LED

Use of the radio code keypad

To protect the radio code keypad keep the cover

closed when it is not in use.

Switch on the keypad light:

• Press the LIGHT button.

The keypad light is on for 5 sec.

Open and close the garage door:

• Enter the programmed 4-digit PIN and then press

the ENTER button. The garage door starts to

move.

• After having pressed the ENTER button, the radio

code keypad remains active for approx. 18 sec.

and the LED is on. During this period of time you

can stop the garage door by pressing any button

(except the LIGHT button).

• Under certain conditions it may be necessary to

keep one button pressed so that your garage door

control works. In this case enter the 4-digit PIN

and then hold the ENTER button. The garage door

moves as long as the ENTER button is held.

Advice:

In case a PIN longer than 4 digits is entered,

only the last 4 digits are considered as

valid. If three wrong PIN's are entered in

sequence, the radio code keypad cuts off to

prevent unauthorised access. After 2 min.

the radio code keypad is ready for use

again.

Light function (to switch other devices):

• To actuate another device (e.g. switch on the yard

light), press the LIGHT button and then the enter

button.

• To switch off the other device (e.g. the yard light),

press the LIGHT button again and then the ENTER

button.

Change the PIN

• Hold "button 0" for approx. 3 sec. until the LED

flashes quickly.

• Enter the PIN to be changed and then press the

ENTER button.

• Enter the new 4-digit PIN and then press the

ENTER button. The LED is on for 2 sec. (no

flashing).

• The radio code keypad is now ready for operation

with the new PIN (the old PIN is no longer valid).

Clear memory

• Press the LIGHT button.

-> After 3 sec. the LED starts to flash quickly.

• Hold the LIGHT button.

• While holding the button, enter PIN 9-9-9-9.

• Release the LIGHT button.

-> The memory is now cleared.

The LED is on for 2 sec.

Advice:

After clearing the memory the radio code

keypad is programmed with 1 random

code and PIN 1-2-3-4.

Replace batteries

• Take a coin to turn the lock on the bottom side of

the wall bracket anti-clockwise. Then take the

radio code keypad out of the wall bracket.

• Unscrew the back cover of the housing of the

radio code keypad.

• Take out the old batteries.

• Insert 2 new 3V batteries, CR 2032. Observe right

poling. Test the function of the unit (The radio

code keypad is designed that it will recognize all

previously programmed codes and PIN's after

change of battery).

• Screw again the back cover of the housing to the

radio code keypad.

Advice:

Don't dispose of old batteries in the

dustbin! Return them to your dealer or

dispose of in a recycling container for used

batteries.

Technical details

Frequency: 868,3 MHz (max. 0.36 mW)

433,92 MHz (max. 0.13 mW)

Voltage: 2 batteries 3V, CR 2032

Current input: approx. 11 mA

Size: 70 x 100 x 30 mm (B x H x T)

Weight: approx. 120 g

Protection category: IP 54

Range of temperature: -20°C to 60°C

Designated use

The radio code keypad is to be used to control door

operator and to switch on and off electrical devices

(power-operated units).

The Declaration of Conformity can be looked up at

the manufacturer mentioned in supply documents.

Simplified EU declaration of

conformity

Hereby, Marantec Antriebs- und Steuerungs technik

GmbH & Co. KG declares that the radio equipment

type Command 231 is in compliance with Directive

2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet

address:

www.marantec.com

᪾

Version: 09.2017

#70794

1 - GB 360232 - M - 0.5 - 0404

Gehäuseunterschale

2Batterien3V,CR2032

2 batteries 3V, CR 2032

Back cover of housing

Produkt Specifikationer

Mærke:	Marantec
Kategori:	Garageportåbner
Model:	Command 231

Har du brug for hjælp?

Hvis du har brug for hjælp til Marantec Command 231 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Garageportåbner Marantec Manualer

Marantec Digital 302 Manual

30 September 2024

Marantec Comfort 270 Manual

30 September 2024

Marantec Command 181 Easywave Manual

22 September 2024

Marantec Dynamic 127 Manual

14 September 2024

Marantec Command 170 Easywave Manual

26 August 2024

Marantec Comfort TU500 Manual

25 August 2024

Marantec Command 231 Manual

24 August 2024

Marantec Comfort 310 Manual

24 August 2024

Marantec Command 132 Easywave Manual

24 August 2024

Marantec Control 101 Manual

24 August 2024

Garageportåbner Manualer

Nyeste Garageportåbner Manualer

Chamberlain Liftmaster Manual

14 Januar 2025

LiftMaster 8500 Elite Manual

11 Januar 2025

Somfy Freevia Essential Manual

30 December 2025

Craftsman CMXZDCG4910 Manual

30 September 2024

Novoferm Novomatic 803S Manual

22 September 2024

Somfy SOLAR - AKKU KIT Manual

20 September 2024

Berner K60 Manual

20 September 2024

Chamberlain 41REV Manual

19 September 2024

Chamberlain MC100C-P2 Manual

1 September 2024

Sommer Funkcody de luxe (5217) Manual

30 August 2024