MaxGear MAX 5073 super bass system Manual

MaxGear forstærker MAX 5073 super bass system

Læs gratis den danske manual til MaxGear MAX 5073 super bass system (28 sider) i kategorien forstærker. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 12 anmeldelser. Har du et spørgsmål om MaxGear MAX 5073 super bass system, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/28
MAX 5073
Super Bass System
INTRODUCTION
Amplifiers provide high-performance sound reinforcement for your mobile audio equipment. Its ver-
satility enables compatibility with optional Equalizers, Frequency Dividing Network Crossovers, and
other audio processors in a customized system. The Multi-Mode bridging capabilities allow flexibility
in hosting several different speaker configurations.
To achieve optimum performance. We suggest that your stereo components are installed by an aut-
horized MAXGEAR dealer. It is highly recommended that you read this Owners Manual before begin-
ning installation.
AMPLIFIER FEATURES
•SILVER RCA CONNECTORS
• DC TO DC CIRCUITRY
•POWER/PROTECTION LED
• GOLD PLATED SCREW CONNECTIONS
• THERMAL/SHORT/OVERLOAD PROTECTION CIRCUTIRY
• VARIABLE BASS BOOST (0-18Db)
•HI/LO SELECT SWITCH
•VARIABLE HPF/LPF CROSSOVER
• ADJUSTABLE INUT SENSITIVTY
• SUBSONIC FILTER 20-50HZ (V-317SX)
SUBWOOFER FEATURES
•5/8” MDF CONSTRUCTION
•HEAVY DUTY INDUSTRIAL CARPET
• HIGH POWER SUBWOOFERS
WARNING
High powered audio systems in a vehicle are capable of generating “live Concert” high levels of sound
pressure. Continued exposure to excessively high volume sound levels may cause hearing loss or
damage. Also, operation of a motor vehicle while listening to audio equipment at high volume levels
may impair your ability to hear external sounds such as; horns, warning signals, or emergency vehi-
cles, thus constituting to a potential traffic hazard.
MAX 5073
Super Bass System
MOUNTING YOUR AMPLIFIER
The mounting position of your Amplifier will have a great effect on its ability to dissipate the heat
generated during normal operation. It has an ample heat sink for heat dissipation, and is also design-
ed with a thermal shut-down protection circuit, making it reasonably tolerant of mounting variations.
Any configuration which allows moving air to be directed over the cooling fins will improve heat dis-
sipation dramatically. DO NOT enclose the amplifier in a small box or cover it so that air cannot flow
around the heat sink fins.
Temperatures in car trunks have been measured as high as 175 F (80 C) in the summer time. Since
the thermal shut-down point for the Amplifier is 185 F (85 C), it is easy to see that it must be moun-
ted for maximum cooling capability. To achieve maximum advantage of convection air flow in an
enclosed trunk, mount the amplifier in a vertical position, on a vertical surface.
Cooling requirements are considerably relaxed when mounting inside the passenger compartment
since the driver will not often allow temperatures to reach a critical point. Floor mounting under the
seat is usually satisfactory as long as there is at least 1 inch (2,5cm) above the Amplifier’s fins for
ventilation.
a. Select a suitable location that is convenient for mounting, is accessible for wiring, and has ample
room for air circulation and cooling.
b. Use the amplifier as a template to mark the mounting holes. Remove the Amplifier and drill 6 holes.
USE EXTREME CAUTION, INSPECT UNDERNEATH SURFACE BEFORE DRILLING.
c. Secure the Amplifier using the screws provided.
CONNECTING THE POWER
CAUTION! AS A PRECAUTION. IT IS ADVISABLE TO DISCONNECT THE VEHICLE’S BATTERY BEFORE
MAKING CONNCETIONG TO THE+12 VOLT SUPPLY WIRING.
10 GAUGE (or a large gauge of wire if planning for additional Amplifiers) wire is recommend the power
and ground wires. 20 Gauge, for the remote turn-on wire. Both types are available at most Mobile
Audio Dealers or installation Shops.
GROUND To Vehicle Chassis
Toavoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be groun-
ded to a clean, bare, metal surface of the vehicle’s chassis.
NOTE: GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT.(1 METER)
USING THIS METHOD CAN CAUSE TURN ON AND TRUN OFF TRANSIENTS (NOISE)
+12 Volt (Fused)Constant Power: To Battery (+)
Due to the power requirements of the Amplifier, this connection should be made directly to the posi-
tive (+) terminal of battery. For safety measures, install an in-line 50 Amp Fuse Holder(not
included)as close to the battery positive (+) terminal as possible, with an ampere rating not to exceed
the total value of fuses in amp.
Remote Turn-On Input: To Power Antenna output of Car Stereo
This Amplifier is turned “ON” remotely when the vehicle’s stereo is turned “ON”.
NOTE: IF YOUR RADIO DOES NOT HAVE A +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED
ON, “RMT” TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLE’S ACCESSORY CIRCUIT
THAT IS LIVE WHEN THE KEY IS “ON”.

Produkt Specifikationer

Mærke: MaxGear
Kategori: forstærker
Model: MAX 5073 super bass system

Har du brug for hjælp?

Hvis du har brug for hjælp til MaxGear MAX 5073 super bass system stil et spørgsmål nedenfor, og andre brugere vil svare dig


forstærker MaxGear Manualer

MaxGear

MaxGear MAX 5073 super bass system Manual

26 August 2024

forstærker Manualer

Nyeste forstærker Manualer

Advance Acoustic

Advance Acoustic MPP-505 Manual

15 Januar 2025
Samson

Samson MXS3000 Manual

14 Januar 2025
Marantz

Marantz PM-11S3 Manual

11 Januar 2025
Bluetech

Bluetech Hi series Manual

22 September 2024
Advance Acoustic

Advance Acoustic MAP-308 Manual

18 September 2024
Marantz

Marantz PM-12 SE Manual

29 August 2024
Marshall

Marshall Code 25 Manual

26 August 2024
Marshall

Marshall Code - PEDL-91009 Manual

26 August 2024
DAP-Audio

DAP-Audio Palladium Vintage P1200 Manual

26 August 2024
Engl

Engl Screamer 50 Manual

26 August 2024