MB Quart NA2-500.5 Manual

MB Quart Modtager NA2-500.5

Læs gratis den danske manual til MB Quart NA2-500.5 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om MB Quart NA2-500.5, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

For power cable runs over 20 feet,

8ga is recommended.

Power cable size

and fusing

It is critical to use the proper power

and ground cable. Select the size

listed here for your amplier model.

Always use high quality copper

cable. Visit our website for multi amp

system cable recommendations.

Be sure to use the proper fuse size

for each model. Some models require

an external fuse.

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Attach the chassis ground, +12V and remote wire.

It is important to make sure these connections are

very secure.

Bare metal

Connect the RCA cables to

the INPUT connectors. The

OUTPUT can be used to

provide input for a second

amplier.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

Connect the speaker cables to

the speaker output connectors.

Follow the diagram below

that best ts your speaker

conguration.

The chassis ground connection

is critical to the performance

of the amplier. Choose a

location that is close to the

amplier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Disconnect

Negative Battery

Terminal

Run Cables

Mount Amplier

Power

Connection

Signal Input

Connection

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Speaker

Connections

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Installation

Before you start

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

Turn the GAIN control completely

counter-clockwise to minimum.

Gain Control

10ga

Model Fuse Size Cable Size

NA2-400.2RC

NA2-320.4

NA2-400.1

NA2-500.5

1-30A atc

1-40A atc

Ground - Black

Remote - Blue

+12V - Red

Speaker Positive - Gray

Left Positive - White

Left Negative - White / Black

Left Front Positive - White

Left Front Negative - White / Black

Right Positive - Gray

Right Negative - Gray / Black

Right Front Positive - Gray

Right Front Negative - Gray / Black

Left Rear Positive - Green

Left Rear Negative - Green / Black

Right Rear Positive - Purple

Right Rear Negative - Purple / Black

Speaker Negative - Gray / Black

GAIN

MIN MAX

NA2-400.1 / NA2-500.5

NA2-400.2RC

NA2-320.4 / NA2-500.5

Setup

Quick Start

Installation Guide

The illustrations below describe the various controls. Refer to

the illustration that matches your amplier.

The gain control purpose is to match

the output of your source signal to the

amplier. Refer to the section B below for

detailed instructions.

This switch will set the amplier to have a

full frequency output or to lter out high or

low frequencies. The NA1-400.2RC offers

either a bandpass or a high pass lter.

The Boost Switch will increase the signal

12dB at 45Hz. Be aware this setting can

cause distortion if the gain is not set

properly.

1. If possible, with the source unit off, conrm that the primary volume control is

turned down (counter clockwise).

2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is

turned down. Make sure the source unit controls; balance, fader, bass and

treble are all set to center or “0” adjustment. Make sure that the green LED on

the end of the amplier is illuminated.

3. Play a clean musical selection of which you are very familiar. CD is preferred.

Do not use radio signals for level setting. Hit play and start turning the volume

of the source unit up.

4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until

you hear speakers begin to slightly start producing distortion.

5. Increase the amplier gain (clockwise) until distortion is heard, then back

the level down (counter clockwise) until the distortion is eliminated. Small

adjustments may need to be made to balance the levels of multiple ampliers.

Settings

This is a critical step to insure your amplier

is properly adjusted to match the signal

output level of your source unit.

THIS IS NOT A VOLUME CONTROL!

Level Setting

WARRANTY

Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from

defects in material and workmanship for a period of one (1) year from the date of purchase.

Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty

period. Components that prove to be defective in materials and workmanship under proper installation

and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was

purchased. A photocopy of the original receipt must accompany the product being returned. The

costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics

USA Inc. This warranty is limited to defective parts and specically excludes any incidental or

consequential damages connected therewith. To view the full warranty, please visit the website.

The information contained within this document is intended to offer some basic guidelines

for a few of the most common installations. More complex audio systems should be

installed by a competent professional. Additional installation information available at

www.maxxsonics.com

MBQuart products are designed and engineered in the USA by

www.maxxsonics.com

Congratulations on your choice of a MBQuart amplier.

This “Quick Start Installation” guide is meant to help you

“hook up” and play music. For more detailed information,

on system setting, speaker and subwoofer conguration

and full specications by model visit the website,

http://mbquart.com/manuals.html

MBQ NA2 QSG 01 - rev3

NA2-400.2RC

NA2-320.4

NA2-400.1

NA2-500.5

GAIN

MIN MAX

NA2-400.1

NA2-400.2RC

X-OVER

OFF

INPUT

LEVEL HP LP

9V 0.2V 15Hz 300Hz 50Hz 300Hz

LEVEL

9V 0.2V

FRONT

X-OVER

OFF

LEVEL

9V 0.2V

REAR

X-OVER

OFF

INPUT

REAR

BOOST

0dB 12dB

INPUT

LEVEL

9V 0.2V

LPF

50Hz 150Hz

SUBSONIC

15Hz 50Hz

NA2-320.4

NA2-500.5

1 3 4

GAIN Adjustment

X-OVER Switch

BOOST Switch

The Low Pass Filter will cut off the

frequencies above the setting. The High

Pass Filter will cut off the frequencies

below the setting.

The Subsonic Filter will cut off the

frequencies below the setting. If using

with a subwoofer the settin should be kept

between 15-25Hz.

Frequencies Adjustment

SUBSONIC Adjustment

Some models include a bass

remote. Avoid adjusting the bass

remote while operating vehicle.

Remote Level

Control

Produkt Specifikationer

Mærke:	MB Quart
Kategori:	Modtager
Model:	NA2-500.5

Har du brug for hjælp?

Hvis du har brug for hjælp til MB Quart NA2-500.5 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager MB Quart Manualer

MB Quart NA2-500.5 Manual

7 Juli 2025

MB Quart RA1-1500.1 Manual

6 Juli 2025

MB Quart RA1-1100.4 Manual

6 Juli 2025

MB Quart NA2-400.2 Manual

19 Juni 2025

MB Quart NA2-320.4 Manual

17 Juni 2025

MB Quart NA2-400.2RC Manual

17 Juni 2025

MB Quart NA2-400.1 Manual

17 Juni 2025

MB Quart FA2-1000.1 Manual

29 Marts 2025

MB Quart FA2-900.5 Manual

29 Marts 2025

MB Quart FA2-2000.1 Manual

28 Marts 2025

Modtager Manualer

Nyeste Modtager Manualer

Rotel DX-3 Manual

7 Juli 2025

Extron NetPA U 1004 Manual

7 Juli 2025

Extron NetPA U 2002 Manual

6 Juli 2025

PureTools PT-R-HD20 Manual

6 Juli 2025

Audiotec Fischer HELIX P SIX DSP Ultimate Manual

6 Juli 2025

Pure Acoustics AZ 2U-5500 Manual

6 Juli 2025

Extron NetPA U 1002 Manual

5 Juli 2025

AudioSource ADTV2.1 Manual

5 Juli 2025

McIntosh MC3500 MKII Manual

5 Juli 2025

Anthem MDX-12 Manual

5 Juli 2025