MB Quart RA1-1100.4 Manual

MB Quart Modtager RA1-1100.4

Læs gratis den danske manual til MB Quart RA1-1100.4 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om MB Quart RA1-1100.4, eller vil du spørge andre brugere om produktet?

Side 1/2
Connect the RCA cables to the
INPUT connectors.
Signal Input
Connection
8
Attach the chassis ground
cable to the amplier
negative terminal. It is
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Chassis Ground
5
7
6
4
POWER
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
INPUT
LEVEL
Place terminal in a secure
position so that it wont
accidentally contact the
negative battery post
Power cable size
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper cable.
Power cable size and fuse size based on a 17ft power (B+) (OFC) cable length and
18-inch ground (OFC) oxygen free cable.
Any other lengths used please consult a certied professional installer.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Disconnect
Negative Battery
Terminal
Run Cables
Mount Amplier
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when disconnected from
battery power. This is an anti-theft feature. Before unplugging power, you must
determine if your radio/source unit requires a reset code. Check the operation
manual for your vehicle or contact the dealer.
1
2
3
4ga
Cable Size
RA1-150.2
RA1-280.4
RA1-1100.4
RA1-300.1
RA1-750.1
RA1-1500.1
RA1-710.5
20 a External
40 a External
90a E xternal
40 a External
80 a External
80 a External
150a Ex ternal
Congratulations on your choice of a MBQuart amplier. This “Quick Start
Installation” guide is meant to help you “hook up” and play music. For more
detailed information, on system setting, speaker and subwoofer conguration
and full specications by model please visit our website at www.MBQuart.com
Model Fuse Size
Connect the power cable to the positive
battery terminal. The power cable must
be fused within 18 inches of the battery
terminal.
Re-connect the negative battery
terminal making sure it is securely
tightened.
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Be prepared to disarm your vehicles alarm and
to enter your radio / source unit code.
10
11
2ch - Full Range
4ch - Full Range
4ch - Mixed Mono
Mono
5 ch
BRIDGED
CH1 CH2
BRIDGED
CH1 CH2
BRIDGED
CH3 CH4
BRIDGED
CH3 CH4
BRIDGED
CH1 CH2
SPEAKER OUTPUT
Speakers Subwoofer
CH 1
CH 2
CH 3
CH 4
CH 5
FULL
HP
LP
CROSSOVER
MODE
SUBSONIC
FREQUENCY
LOW PASS
FREQUENCY
50Hz 250Hz
Set INPUT MODE switch to 4CH.
Set CH3&4 LOW PASS MODE.
Set INPUT MODE switch to 4CH.
Set CH3&4 LOW PASS MODE.
Set INPUT MODE to 5CH.
Set CH1&2 and CH3&4 CROSSOVER switch to HP.
Common System Setup


Produkt Specifikationer

Mærke: MB Quart
Kategori: Modtager
Model: RA1-1100.4

Har du brug for hjælp?

Hvis du har brug for hjælp til MB Quart RA1-1100.4 stil et spørgsmål nedenfor, og andre brugere vil svare dig