MB Quart FA2-1000.1 Manual

MB Quart Modtager FA2-1000.1

Læs gratis den danske manual til MB Quart FA2-1000.1 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 4 anmeldelser. Har du et spørgsmål om MB Quart FA2-1000.1, eller vil du spørge andre brugere om produktet?

Side 1/2
External 40A
External 100A
External 80A
External 100A
External 125A
Place terminal in a secure
position so that it wont
accidentally contact the
negative battery post
Power cable size
and fusing
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
for each model.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicles alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
4
POWER
REM turn on (Remote wire turn on)
when using High Level Input
- DC turn on
- Signal Sense turn on
Auto-Sense
Technical Guide
Turn on Mode
9
Model Fuse Size Cable Size
4ga
FA2-400.4
FA2-900.5
FA2-1000.1
FA2-1500.1
FA2-2000.1
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock
single woofer multiple woofersMonoblock
Bridged
10
CH1 CH2
SPEAKER
SPEAKER
REM
ON
DC
ON
SIGNAL
ON
MODE
NOTE - If the RCA’s are plugged into the amplier and the TURN ON MODE is in the
DC ON position, the amplier will NOT turn on. Please re-read QR document above or
hire a professional installer.


Produkt Specifikationer

Mærke: MB Quart
Kategori: Modtager
Model: FA2-1000.1

Har du brug for hjælp?

Hvis du har brug for hjælp til MB Quart FA2-1000.1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager MB Quart Manualer

Modtager Manualer

Nyeste Modtager Manualer

Jensen

Jensen JA2CH Manual

29 Oktober 2025
Kramer

Kramer WP-DEC7 Manual

17 Oktober 2025
FBT

FBT MXA 3120 Manual

17 Oktober 2025
Rotel

Rotel C8 Manual

15 Oktober 2025
Rotel

Rotel RA-11 Manual

15 Oktober 2025
Rotel

Rotel A10 MKII Manual

15 Oktober 2025
Ecler

Ecler GPA2-800 Manual

15 Oktober 2025
Axiom

Axiom ADA-1000 Manual

14 Oktober 2025