Metra TE-2PSK Manual

Metra dashcam TE-2PSK

Læs gratis den danske manual til Metra TE-2PSK (8 sider) i kategorien dashcam. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Metra TE-2PSK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

iBEAMUSA.comiBEAM Vehicle Safety Sytems

REV. 04/18/2022 INSTTE-2PSK

Attention!

When testing the aftermarket

equipment, ensure that all factory equip-

ment is connected before cycling the key to

ignition.

TE-2PSK

INSTALLATION INSTRUCTIONS

#IBEAMSAFETY

Technical Tip............................................................2

Installation ......................................................... 3-5

Calibration ..............................................................6

Wiring digrams and specs ................................4-5

TABLE OF CONTENTS

TOOLS REQUIRED

• Wire stripper

• Tape

• Digital Multi-meter

• Cutter

• Alcohol wipes/cleaning pads

Universal 2 Sensor No Drill

Parking Sensor Kit

Visit iBEAMUSA.com for more detailed informatuon about the product and up-to-date vehicle specific

applications.

Product Features

• 2 sensor parking solution

• No need to drill into the bumper

• Audible 3-zone alerts

• No additional control box needed

• Use for plastic bumpers only

• Easy to install

Part Components

A) 2 Sensors B) Wiring harness C) Accessories

A B C

386-257-1187

iBEAMUSA.com

Installation

NOTE: This installation may require the

removing of the bumper to get the proper

sensor alignment.

1. Before removing of the bumper (if it

is needed) iBEAM suggests measuring

the placement of the sensors on

the outside of the bumper with the

provided ruler and painters tape.

2. Tape off the vertical mounting location

15-24 inches from the ground. Find the

flatest surface possible. (Figure A.1)

3. Find the center of the bumper. Tape

off two positions between 10 and 20

inches from the center on the left and

right hand side. Again, find the flatest

surface possible. (Figure A.2)

4. These tape markswill be used to

indicate where on the opposite side

the sensors will be mounted once the

bumper is removed.

5. Remove the bumper. Each vehicle is

different. Take care with removal, lay

a cloth on the ground to protect the

exterior paint from damage.

Figure A

15-24 in15-24 in 15-24 in

10-20 in10-20 in

TECHNICAL TIP

Produkt Specifikationer

Mærke:	Metra
Kategori:	dashcam
Model:	TE-2PSK

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra TE-2PSK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

dashcam Metra Manualer

21 August 2024

20 August 2024

20 August 2024

20 August 2024

20 August 2024

18 August 2024

Metra TE-FDHDH Manual

18 August 2024

Metra TE-FDFTG Manual

18 August 2024

Metra TE-SRBC Manual

18 August 2024

Metra TE-TUTGC Manual

18 August 2024

dashcam Manualer

Nyeste dashcam Manualer

Mio MiVue J20 Manual

21 Februar 2025

BlackVue CM100GLTE Manual

19 Februar 2025

Kogan KAACCHWKITA Manual

11 Februar 2025

Hikvision AE-DC5313-C6 Manual

7 Februar 2025

Thinkware X1000 Manual

2 Februar 2025

Navman DDR MiVue 740 Manual

14 Januar 2025

Navman Smart Box II Manual

14 Januar 2025

Rexing V33 Manual

13 Januar 2025

Alpine PKG-RSE3DVD Manual

12 Januar 2025

Cobra SC 250R Manual

11 Januar 2025