Microchip HV816DB2 Manual

Microchip Ikke kategoriseret HV816DB2

Læs gratis den danske manual til Microchip HV816DB2 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Microchip HV816DB2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Supertex inc.

www.supertex.com

HV816DB2

Doc.# DSDB-HV816DB2

A061013

The Supertex HV816DB2 is a high brightness demoboard

with the circuitry to drive a 10in2 EL lamp using the HV816 in

a 4x4 QFN-16 package.

Simply connect the board to a power supply and an EL lamp

as shown in the circuit schematic on the following page.

The HV816DB2 circuit has been optimized to drive an EL

lamp size of 10in2. For different EL frequencies or smaller

EL lamps sizes, the demoboard can be re-optimized by

changing some of the component values.

The output voltage is typically ±180V for high lamp

brightness, using a single supply input voltage of 5.0V. An

external N-channel MOSFET, Supertex TN2425 is used to

boost the output voltage to a nominal value of 180V with an

input voltage of 5.0V.

For split supply applications, the diode BAS20 between VIN

and VDD has to be removed so separate supplies can be

used for VIN and VDD.

The discharge rate on the output for EL lamp can be adjusted

to minimize audible noise. By increasing the value of the

RSLEW resistor, the discharge rate will increase, which will

reduce audible noise but will also reduce brightness. RSLEW

can be set to a value between 100kΩ and 500kΩ with 100kΩ

for maximum brightness.

The HV816DB2 has the provision to set the EL lamp frequency

using the resistor REL on the board or by an external clock

input at the SEL pin. To use an external clock input, the REL

resistor should be removed and the REL-Osc pin should be

connected to GND.

Board Layout and Connection Diagram

Specications

VDD input voltage 2.7 to 5.5V

VIN inductor supply voltage 4.5 to 5.0V

Typical supply current 150mA

Lamp size 10in2

Lamp frequency 190Hz

Converter frequency 150kHz

Board dimensions 27mm x 27mm

General Description

CDD

RREG RSLEW

CIN

RSW

CSW

REL

CFEL

EL Lamp

5.0V

1.5 to

5.0V

High Brightness 10in2

EL Lamp Driver Demoboard

HV816DB2

Supertex inc.

www.supertex.com

Doc.# DSDB-HV816DB2

A061013

HV816DB2 Circuit Schematic

Typical Performance

VDD = VIN

(V)

IIN

(mA)

VCS

(VPEAK)

fEL

(Hz)

Lamp Brightness

ft-lm cd/m2

5.0 150 190 190 15 50

HV816K6-G

ES1D

RREG

100kΩ

RSW = 590kΩ

REL = 1.0MΩ

RSLEW

100kΩ

EL Lamp

VREG

GATELX VDRIVE

VOUT

RSLEW-OUT

SEL

RSW-Osc

REL-Osc

VDD

HVGND GND

CFEL

100nF

CSW

100nF

CDD

100 Fµ

CIN

100 Fµ

100nF

LPS5030-473ML

TN2425N8

VIN = 5.0V

3.3nF

200V

NPO

BAS20

EN = 1.5V to VDD

13 7 8

Backside

Slug

1416 15

Note:

CIN can be in the range of 47 to 100µF.

CDD can be in the range of 47 to 100µF.

Connections:

VIN, Input

Inductor input voltage. Single supply can be used for VIN and

VDD or separate supplies can be used. If separate supplies

are used, the diode BAS20 between VIN and VDD has to be

removed. The input range for VIN is 4.5 to 5.0V.

VDD, Input

Device input voltage.Single supply can be used for V IN

and

VDD or separate supplies can be used. If separate supplies

are used, the diode BAS20 between VIN and VDD has to be

removed. The input range for VDD is 2.7 to 5.5V.

GND

Device Ground. Connect to power supply ground.

EN, Input

A CMOS logic input which enables/disables the lamp driver.

A logic high (1.5V to VDD

) enables the driver and a logic low

(0 to 0.2V) disables the driver.

SEL, Input

CMOS logic input to set the EL frequency. To use this pin, the

REL-Osc pin should be connected to GND. The frequency

input at this pin should be 4x the desired output frequency.

An external CLK signal can be used for this input. If this pin

is not used, it should be connected to ground.

VA and VB Outputs

VA and VB are for EL Lamp connections. They should be

connected to an EL lamp. Polarity is irrevelant.

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	HV816DB2

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip HV816DB2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip AT7913 Manual

1 September 2025

Microchip ATmega1281 Manual

19 Juli 2025

Microchip ATtiny461 Manual

19 Juli 2025

Microchip ATxmega128D3 Manual

19 Juli 2025

Microchip ATxmega128D4 Manual

19 Juli 2025

Microchip ATTINY28 Manual

19 Juli 2025

Microchip ATTINY861 Manual

19 Juli 2025

Microchip ATmega1280 Manual

19 Juli 2025

Microchip ATtiny84A Manual

19 Juli 2025

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock PT44 Manual

14 September 2025

BSS Audio FDS-366T Manual

14 September 2025

Systemair Airline R-114 Manual

14 September 2025

IFM SU2031 Manual

14 September 2025

Morel Tempo Ultra Integra 502 Manual

14 September 2025

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025