Microchip MIC23450-AAAYML Manual

Microchip Ikke kategoriseret MIC23450-AAAYML

Læs gratis den danske manual til Microchip MIC23450-AAAYML (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Microchip MIC23450-AAAYML, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

MIC23450 Evaluation Board

3 , , MHz PWM 2A Triple Buck Regulator

with HyperLight Load

and Power Good

HyperLight Load is a trademark of Micrel, Inc.registered

MLF and LeadFrame are registered trademark Amkor Technology Inc.Micro

Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 ( ) 944 0800 • fax + 1 (408) 474 1000 • 408 - - http://www.micrel.com

February 4, 2013

Revision 1.0

General Description

This board allows the customer to evaluate the

MIC23 output 3MHz450, a fully integrated, triple- - , 2A,

switching regulator that features HyperLight Load ® mode

and ood 450 power g (PG) output indicator . The MIC23s

is highly efficient throughout the output current range,

drawing just 23 A of quiescent cu for each channel µ rrent

in operation. The tiny 5mm x 5mm MLF® package saves

board space and requires few external components. The

MIC23450 provides 2.5% accuracy and± output voltage

each channel typically in less than 10 to a responds µs

load transient with output voltage ripple.as low as 5mV

Requirements

This board needs a single 40W bench power source,

adjustable from to 5.5 . The loads can 2.7V V be either

active (electronic load) or passive (re and must be sistor),

able to to dissipate 20W. It is ideal, but not essential,

have an oscilloscope available to view the circuit

waveforms. require oltage The simplest tests vtwo

meters to measure input and output voltage. Efficiency

measurements require oltage for a single channel vtwo

meters and meterstwo am to prevent errors caused by

measurement inaccuracies.

Precautions

There is no reverse input protection on this board. Be

careful make when connecting the input source to sure

correct polarity is observed.

Getting Started

1. Connect an external supply to the VIN ) (J1

terminal and (JGND 3).

With the output of the power supply disabled, set its

voltage to the desired input test voltage (2.7V ≤ VIN ≤

5.5V). An ammeter may be placed between the input

supply and the VIN ( ) . J1 terminal Be sure to monitor

the supply voltage at the VIN ( ) J1 terminal, as the

ammeter and/or power lead resistance can reduce

the voltage supplied to the device.

2. Connect a load Vto the OUT terminals (J2, J5, J7)

and ground (J4, J6, J8) .terminals

The load can be either active passive (resistive) or

active (electronic load). An ammeter may be placed

between the load and the output terminals s. Make

sure the output voltage is monitored at VOUT1, VOUT2

and VOUT3 ( ) s. J2, J5 and J7 terminal The board has

multiple 2- s ) pin connector (JP1, JP2 and JP3 to

allow for output voltage monitoring of VOUT1

, VOUT2

and VOUT3 . respectively

3. Enable the Supply to MIC23450.

The MIC23450 evaluation up board has a pull-

resistor to VIN for each channel By default, . each

output voltage bled when the input supply of is ena

> V 2.7 is applied. Each channel 1, 2 or 3 can be

disabled by the Eapplying 0.4 a voltage below V to N

terminal or J14 respectivelyJ10, J12 .

4. Power Good.

The board provides a test point power ood g (J9,

J11, and J13 to monitor for ) the power good function

each channel The of the s 1, 2, and 3 respectively.

power good output high (goes VOUT) nominally 62 µs

after reaches the output voltage 90% of its nominal

voltage.

Ordering Information

Part Number Description

MIC23 YML450-AAA EV 3MHz, PWM,

2A Triple Buck

R egulator Evaluation Board

Micrel, Inc.

MIC23450 Evaluation Board

February 4, 2013 2 Revision 1.0

Evaluation Board

Other Features

S -S oft tart

The MIC23450 has an internal soft start for each

individual channel and requires no external soft start

capacitor. The typical soft start time for each channel is -

115µs.

Feedback Resistors , R14 -(R4 R7, R12 )

The feedback pin the control s , FB1, FB2 and are FB3

inputs for programming the output voltages VOUT1, VOUT2

and VOUT3 R s respectively. esistor divider network are

connected to from the output and these pin s are

compared to the internal 0.62V reference within the

regulation loop. The output voltage can be programmed

between 1V and 3.3V using resistor values calculated by

Equation 1:











+⋅=











+⋅=











+⋅=

R14

R12

1VV

REFOUT3

REFOUT2

REFOUT1

Eq. 1

Example feedback resistor values are provided in Table

Table 1

Output Voltage Programming Examples

VOUT1, VOUT2, VOUT3 R4, R6, R12 R5, R7, R14

1.2V 274k 294k

1.5V 316k 221k

1.8V 301k 158k

2.5V 324k 107k

3.3V 309k 71.5k

Power Good (PG1, PG2, PG3)

The evaluation board as test point s 1, 2, h s for channel

and 3 to monitor the PG 1, PG2 and PG3 signal These s.

are open to the corresponding output -drain connections

voltage of with on-board pull up resistor- s 100kΩ. The

PG signal will be µs asserted high approximately 62 after

the output voltage passes nominal set 90% of the

voltage.

Hyper Light Load Mode

The MIC23450 uses a minimum on and off time

proprietary control loop (patented by Micrel). When the

output voltage falls below the regulation threshold, the

error comparator begins a switching cycle that turns the

PMOS on and keeps it on for the duration of the

minimum- -on time. This increases the output voltage. If

the output voltage is over the regulation threshold, the

error comparator turns the PMOS off for a minimum-off-

time until the output drops below the threshold. The

NMOS acts as an ideal rectifier that conducts when the

PMOS is off. Using a NMOS switch instead of a diode n

allows for lower voltage drop across the switching device

when it is on. The asynchronous switching combination

between the PMOS and the NMOS allows the control

loop to work in discontinuous mode for light load

operations. In discontinuous mode, the MIC23450 works

in pulse frequency modulation (PFM) to regulate the

output. As the output current increases, the off-time

decreases, which provides more energy to the output.

This switching scheme improves the efficiency of

MIC23450 during light load currents by switching only

when it is needed. As the load current increases, the

MIC23450 goes into continuous conduction mode (CCM)

and switches at a frequency centered at . The 3MHz

equation to calculate the load when the MIC23450 goes

into continuous conduction mode is approximated by

Equation 2:













×−

>f2L

D)V(V

OUTIN

LOAD

2 Eq.

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	MIC23450-AAAYML

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC23450-AAAYML stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip HS12-100D0/12DS2F Manual

18 Februar 2025

Microchip HSA0-040SDA/A0SA10 Manual

18 Februar 2025

Microchip HSA0-040SIA/A0S1F Manual

18 Februar 2025

Microchip HT12-100S0s/12ST25 Manual

17 Februar 2025

Microchip EMC2103-2 Manual

17 Februar 2025

Microchip EMC1047 Manual

17 Februar 2025

Microchip HCS201 Manual

17 Februar 2025

Microchip LE9653 Manual

17 Februar 2025

Microchip LAN7430 Manual

17 Februar 2025

Microchip HCS500 Manual

17 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025