Microchip MIC3230 Manual

Microchip Ikke kategoriseret MIC3230

Læs gratis den danske manual til Microchip MIC3230 (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Microchip MIC3230, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
July 2009 M9999-071609-A
(408) 944-0800
General Description
The MIC3230/1 are constant current boost switching
controllers specifically designed to power one or more
strings of high power LEDs. The MIC3230/1 have an input
voltage range from 6V to 45V and are ideal for a variety of
applications.
The MIC3230/1 utilizes an external power device which
offers a cost conscious solution for driving high power LED
applications. Power consumption has been minimized
through the implementation of a 250mV feedback voltage
reference providing an accuracy of ±3%. The MIC3230/1
are dimmable via a PWM input signal and also features an
enable pin for low power shutdown.
The LED current is regulated by keeping the voltage drop
across the current sense resistor (R7) constant. The LED
current can be set by selecting the value of R7. In this
version of the eval board, the output current is limited to
750mA.
Multiple MIC3230 ICs can be synchronized to a common
operating frequency by connecting the ICs together
through the SYNC pin. This feature is only good on the
MIC3230. The clocks of these synchronized devices can
be used together which help reduce noise and errors in a
system.
The MIC3231 offers a dither feature to assist in the
reduction of EMI. This is particularly useful in sensitive
EMI applications, and provides for a reduction in emissions
by approximately 10dB.
Table 1 provides a summary of the eval board
specifications. The evaluation board schematic is shown in
Figure 1 and the parts list is shown in the Bill of Materials
table.
The switching frequency is determined by the selection of
R1. The chart in Figure 2 can be used to select the
desired frequency. The board is set at approximately
500kHz.
Requirements
1. Voltage source capable of supplying 50 Watts
2. Load: LED, resistive or electronic load
3. Scope
4. Voltage meter
5. (Optional) Function generator for PWM Dimming
Precautions
The evaluation board does not have input reverse polarity
protection. Applying a negative voltage at the VIN terminal
may damage the board. When the controller is off there is
a current path through the inductor and the flyback diode
to the output. No current limit exists for this current path so
care must be taken not to short circuit the output.
How it works
The MIC3230/1 evaluation board is set to operate as a
boost converter, which requires the output voltage to be
greater than the input voltage. It is important to have the
series LED forward voltage drops be greater than the input
voltage because when the converter is off the input is
connected to the output through the inductor (L1) and
diode (D1). VIN is effectively applied across the LEDs and
will turn on if the series sum of their forward voltage drop is
not greater than VIN. For 100% duty cycle, simply pull
PWMD high or leave open. For a different LED current
change R7 using the following equation. When R7 is
0.62Ω, the LED current is equal to 0.4A. The evaluation
board is currently set to this output current value.
7R
V
IREF
LED = Where VREF = 0.25V
PWM Dimming
A PWM signal applied to the PWMD pin turns the current
to the load LEDs on and off. When PWMD is high the
MIC3230/1 is enabled and the boost converter regulates
the LED current by keeping the voltage drop across R7
constant. When PWMD is low the converter turns off and
the LED current discharges the output caps and LED
current stops.
Ordering Information
Part Number Description
MIC3230ML
BOOST EV
Boost evaluation board for the
MIC3230YML IC
MIC3231ML
BOOST EV
Boost evaluation board for the
MIC3231YML IC

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC3230

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC3230 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip PIC16F87 Manual

25 Oktober 2025
Microchip

Microchip PIC18F2620 Manual

25 Oktober 2025
Microchip

Microchip RN240 Manual

24 Oktober 2025
Microchip

Microchip PIC24HJ12GP201 Manual

24 Oktober 2025
Microchip

Microchip TC4420 Manual

24 Oktober 2025
Microchip

Microchip HV2818 Manual

23 Oktober 2025
Microchip

Microchip MIC2298 Manual

23 Oktober 2025
Microchip

Microchip PIC16F630 Manual

23 Oktober 2025
Microchip

Microchip PIC32MZ2048EFG144 Manual

21 Oktober 2025
Microchip

Microchip PIC18F46J50 Manual

21 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MuxLab

MuxLab 500439 Manual

5 November 2025
GVM

GVM BL160-II Manual

5 November 2025
Uniprodo

Uniprodo UNI_ROLL_03 2in1 Manual

5 November 2025
Rockville

Rockville SS6 Manual

5 November 2025
Silk'n

Silk'n VacuPedi FTC04 Manual

5 November 2025
MEPROLIGHT

MEPROLIGHT MCO PRO Manual

5 November 2025
XPG

XPG Battlecruiser II Manual

5 November 2025
Hosa

Hosa USQ-110 Manual

5 November 2025
JMAZ

JMAZ Centipede Quadro Manual

5 November 2025
Lake People

Lake People Mic-Amp F311-D Manual

5 November 2025