Microchip PIC10F222 Manual

Microchip Ikke kategoriseret PIC10F222

Læs gratis den danske manual til Microchip PIC10F222 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Microchip PIC10F222, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
2004 Microchip Technology Inc. DS51491A-page 1
PROGRAMMING PIC10F2XX DEVICES WITH
THE BASELINE FLASH MICROCONTROLLER
PROGRAMMER (BFMP)
INTRODUCTION
The Baseline Flash Microcontroller Programmer (BFMP) together with the PICkit
™1 Baseline Flash Programmer PC
application is designed to program baseline PIC10F2XX Flash devices.
PICkit™1 FIRMWARE REVISION 2.0.0.
When the PICkit 1 PC application is executed with the BFMP connected to a USB port, the firmware version is displayed
in the bottom left corner of the interface window, as shown in Figure 1. If “Firmware Version 2.0.0.” or greater is
displayed, the programmer is ready for use. If lower version number is displayed, disconnect any PICkit 1 Flash demo
boards connected to USB. If the interface window states that the programmer can not be found, check all connections
between the PC, any USB hubs and the BFMP.
FIGURE 1: FIRMWARE VERSION
PIC10F2XX PROGRAMMING
The 6 and 8-pin PIC10F2XX devices require an adapter socket to connect the device to the 6-pin connector at the end
of the BFMP. The user can elect to purchase an adapter board from Microchip (see Universal Programming Adapter
below) or build one using the information in this document.
The procedure for programming a PIC10F2XX device is as follows:
1. Load the PICkit 1 Baseline Flash Programming PC application onto a PC with a Windows
® 98 SE or later
Operating System.
2. Connect the BFMP to the PC using a regular USB cable.
3. Connect the BFMP to the target device through the 6-pin connector on the BFMP, using an appropriate program-
ming adapter.
4. Start the PC application.
5. The application should correctly identify the BFMP firmware version. If not, remove any PICkit boards attached
to the PC and check all USB connections, then restart the application.
6. Select the appropriate device from the Device Configuration window (see Figure 1).
7. Load the hex file using the pull-down File menu on the PC application toolbar.
8. Click on the Write device button.
9. The Progress Bar should grow from left to right until programming is complete.
10. Once programming is complete, the Status Bar should turn green.
11. If not, check all connections to the BFMP and the target device.
Note: The PICkit 1 Baseline Flash Programming PC application can be downloaded from the Microchip
Technology Inc. web site at www.microchip.com.
Information Sheet
PROGRAMMING PIC10F2XX DEVICES WITH BASELINE FLASH MCU PROGRAMMER
DS51491A-page 2 2004 Microchip Technology Inc.
PIC10F2XX UNIVERSAL PROGRAMMING ADAPTER
Microchip offers a PIC10F2XX Universal Programming Adapter that provides connections to the PIC10F2XX devices
for the following programmers:
• PICkit™1 Flash Starter Kit
• PICSTART® Plus Programmer
• MPLAB® ICB 2 In-Circuit Debugger
• BFMP Baseline Flash Microcontroller Programmer
The PIC10F2XX Universal Programmer Adapter, part number “AC163020”, can be ordered online at buy.microchip.com
or by contacting the nearest Microchip Sales locations (see Worldwide Sales and Service listing page).
BUILDING A PIC10F2XX PROGRAMMING ADAPTER
Adapters are electrically single; only 5 pins are used by the programming process. The adapter only needs to connect
the pins from the programmer, to the device to be programmed. No additional active or passive components are
necessary. All other pins should be left unconnected. Schematic and Gerber files for sample adapters are available on
the Microchip web site at www.microchip.com and on the PICkit
™1 Flash Starter Kit CD-ROM (DS40049). The adapter
may be built directly into the target circuit or as a programmer adapter similar to the Universal Programming Adapter.
The information for building a PIC10F2XX adapter board is available in Table 1.
TABLE 1: PIC10F2XX 6-PIN SOT-23 ADAPTER PINS
Note: BFMP Pin 1 is reserved for future expansion and should not be connected.
Programming Pin Description PIC10F2XX Pin Assignment
(SOT-23)
BFMP 6-Pin
Programmer
VDD Power Supply VDD – pin 5 5
VSS SSGround V – pin 2 4
ICSPCLK Serial Clock GP1 – pin 3 2
ICSPDAT Serial Data GP0 – pin 1 3
VPP Programming Mode Select GP3 – pin 6 6

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: PIC10F222

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PIC10F222 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip ATmega1281 Manual

19 Juli 2025
Microchip

Microchip ATtiny461 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D3 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D4 Manual

19 Juli 2025
Microchip

Microchip ATTINY28 Manual

19 Juli 2025
Microchip

Microchip ATTINY861 Manual

19 Juli 2025
Microchip

Microchip ATmega1280 Manual

19 Juli 2025
Microchip

Microchip ATtiny84A Manual

19 Juli 2025
Microchip

Microchip ATmega645P Manual

19 Juli 2025
Microchip

Microchip ATmega16A Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Intellinet

Intellinet 561730 Manual

31 Juli 2025
Oppo

Oppo X7 Ultra Manual

31 Juli 2025
Oppo

Oppo K11 Manual

31 Juli 2025
Bestway

Bestway Hydro-Force 6531R Manual

31 Juli 2025
RYOBI

RYOBI RSCR4 Manual

31 Juli 2025
Advantech

Advantech AIMB-286EF Manual

31 Juli 2025
Tripp Lite

Tripp Lite SUT40KMBP Manual

31 Juli 2025
Tripp Lite

Tripp Lite Protect It! TLP28PD57WCAM Manual

31 Juli 2025
Advantech

Advantech PCIE-1751 Manual

31 Juli 2025
Intellinet

Intellinet 713078 Manual

31 Juli 2025