Microchip PIC24FJ128GL405 Manual

Microchip Ikke kategoriseret PIC24FJ128GL405

Læs gratis den danske manual til Microchip PIC24FJ128GL405 (72 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Microchip PIC24FJ128GL405, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/72

 2008-2012 Microchip Technology Inc. DS01229C-page 1

AN1229

INTRODUCTION

This application note describes the Class B Safety

Software Library routines that detect the occurrence of

Faults in a single channel CPU. These routines have

been developed in accordance with the IEC 60730

standard to support the Class B certification process.

These routines can be directly integrated with the end

user’s application to test and verify the critical

functionalities of a controller without affecting the end

user’s application.

This application note also describes the Application

Programming Interface (API) functions that are

available in the Class B Safety Software Library.

The Class B safety software routines can be called

periodically at start-up or run time to test the following

components:

• CPU Registers

• CPU Program Counter

• Invariable Memory

• Variable Memory

• Clock

• Interrupt Handling and Execution

This application note also outlines various techniques,

which are not part of the Class B Safety Software

Library, to test components such as external communi-

cation, timing, I/O periphery, analog I/O and analog

multiplexer.

OVERVIEW OF THE IEC 60730

STANDARD

The IEC 60730 standard defines the test and diagnostic

methods that ensure the safe operation of the controlled

equipment used in household appliances. Annex H of

the IEC 60730 standard classifies the software into the

following categories (see Appendix B: “IEC 60730-1

Table H.11.12.7”):

• Class A

• Class B

• Class C

The Class B Safety Software Library implements the

important test and diagnostic methods that fall into the

Class B category. These methods use various

measures to detect and respond to the software-

related Faults and errors.

According to the IEC 60730 standard, the controls with

functions that fall into the Class B category should have

one of the following structures:

• Single Channel with Functional Test

In this structure, the Functional test is executed

prior to the application firmware execution.

• Single Channel with Periodic Self-Test

In this structure, the Periodic tests are embedded

within the firmware, and the self-test occurs

periodically while the firmware is in Execution

mode.

• Dual Channel without Comparison

In this structure, two independent methods execute

the specified operations.

Note: The term ‘IEC 60730 standard’ used in

this document refers to the “IEC 60730-1

Switzerland. www.iec.ch.

Authors: Veena Kudva & Adrian Aur

Microchip Technology Inc.

Note: “The author thanks the International Elec-

trotechnical Commission (IEC) for permis-

sion to reproduce information from its

International Standard IEC 60730-1ed.3.2

(2007). All such extracts are copyright of

IEC, Geneva, Switzerland. All rights

reserved. Further information on the IEC is

available from www.iec.ch. IEC has no

responsibility for the placement and con-

text in which the extracts and contents are

reproduced by the author, nor is IEC in any

way responsible for the other content or

accuracy therein.”

Class B Safety Software Library for

PIC® MCUs and dsPIC® DSCs

AN1229

DS01229C-page 2  2008-2012 Microchip Technology Inc.

SYSTEM REQUIREMENTS

The following system requirements are recommended

to run the Class B Safety Software Library:

• For the tests that require the independent time

slot monitoring, the system hardware must be

provided with at least two independent clock

sources (e.g., crystal oscillator and line

frequency).

• The user application determines whether the

interrupts need to be enabled or disabled during

the execution of the Class B Safety Software

Library.

If an interrupt occurs during the execution of the

Class B Safety Software Library routine, an

unexpected change may occur in any of the regis-

ters. Therefore, when the Interrupt Service Routine

(ISR) executes, the contents of the register will not

match the expected content, and the ISR will return

an incorrect result.

CLASS B SAFETY SOFTWARE

LIBRARY

The Class B Safety Software Library, which applies to 8-

bit, 16-bit, and 32-bit devices, includes several APIs,

which are intended to maximize application reliability

through Fault detection. These APIs help meet the IEC

60730 standard compliance. The following tests can be

implemented using this library:

• CPU Register Test

• Program Counter Test

• Variable Memory Test

• Invariable Memory (Flash/EEPROM) Test

• Interrupt Test

• Clock Test

In the following sections, the test description and the

implementation details are discussed for each test. In

addition, each section also lists the APIs that are

required to execute the corresponding test for

supported architectures.

CPU Register Test

The CPU Register test implements the

functional test H.2.16.5 defined by the IEC 60730

standard. It detects stuck-at Faults in the CPU registers.

This ensures that the bits in the registers are not stuck at

a value ‘0’ or ‘1’; this is a non-destructive test.

This test performs the following major tasks:

1. The contents of the CPU registers to be tested

are saved on the stack before executing the

routine.

2. The registers are tested by first successively

writing the binary sequences (length is depen-

dant upon architecture), 010101... followed by

101010... into the registers, and then reading

the values from these registers for verification.

3. The test returns an error code if the returned

values do not match.

API FUNCTIONS

The following API functions implement the CPU

• SSL_8bit_CPU_RegisterTest (PIC10/12/16)

• SSL_8bitsFamily_CPU_RegisterTest (PIC18)

• SSL_16bitsFamily_CPU_RegisterTest

• SSL_32bitsFamily_CPU_RegisterTest

Note: The interrupts should be disabled during

the execution of the CPU Register test so

that the register integrity is preserved at all

times.

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	PIC24FJ128GL405

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PIC24FJ128GL405 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip AT7913 Manual

1 September 2025

Microchip ATmega1281 Manual

19 Juli 2025

Microchip ATtiny461 Manual

19 Juli 2025

Microchip ATxmega128D3 Manual

19 Juli 2025

Microchip ATxmega128D4 Manual

19 Juli 2025

Microchip ATTINY28 Manual

19 Juli 2025

Microchip ATTINY861 Manual

19 Juli 2025

Microchip ATmega1280 Manual

19 Juli 2025

Microchip ATtiny84A Manual

19 Juli 2025

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock PT44 Manual

14 September 2025

BSS Audio FDS-366T Manual

14 September 2025

Systemair Airline R-114 Manual

14 September 2025

IFM SU2031 Manual

14 September 2025

Morel Tempo Ultra Integra 502 Manual

14 September 2025

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025