Microchip PIC32MX450F256L Manual

Microchip Ikke kategoriseret PIC32MX450F256L

Læs gratis den danske manual til Microchip PIC32MX450F256L (72 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Microchip PIC32MX450F256L, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/72

USB On-The-Go

(OTG)

Section 27. USB On-The-Go (OTG)

HIGHLIGHTS

This section of the manual contains the following major topics:

27.1 Introduction .................................................................................................................. 27-2

27.2 Control Registers ......................................................................................................... 27-4

27.3 Operation ................................................................................................................... 27-36

27.4 Host Mode Operation................................................................................................. 27-51

27.5 Interrupts.................................................................................................................... 27-59

27.6 I/O Pins ...................................................................................................................... 27-62

27.7 Operation in Debug and Power-Saving Modes.......................................................... 27-64

27.8 Effects of a Reset....................................................................................................... 27-66

27.9 Related Application Notes.......................................................................................... 27-67

PIC32 Family Reference Manual

27.1 INTRODUCTION

The PIC32 USB OTG module includes the following features:

• USB Full-Speed Support for Host and Device

• Low-Speed Host Support

• USB On-The-Go (OTG) Support

• Integrated Signaling Resistors

• Integrated Analog Comparators for VBUS Monitoring

• Integrated USB Transceiver

• Transaction Handshaking Performed by Hardware

• Endpoint Buffering Anywhere in System RAM

• Integrated Bus Master to Access System RAM and Flash

• USB OTG module does not require the PIC32 DMA module for its operation

The USB OTG module contains analog and digital components to provide a USB 2.0 full-speed

and low-speed embedded host, full-speed device, or OTG implementation with a minimum of

external components. This module in Host mode is intended for use as an embedded host and

therefore does not implement a UHCI or OHCI controller.

The USB OTG module consists of the clock generator, the USB voltage comparators, the trans-

ceiver, the Serial Interface Engine (SIE), a dedicated USB Bus Master, pull-up and pull-down

resistors and the register interface. A block diagram of the USB OTG module is presented in

Figure 27-1.

The clock generator provides the 48 MHz clock, which is required for USB full-speed and

low-speed communication. The voltage comparators monitor the voltage on the VBUS pin to

determine the state of the bus. The transceiver provides the analog translation between the USB

bus and the digital logic. The SIE is a state machine that transfers data to and from the endpoint

buffers, and generates the hardware protocol for data transfers. The USB Bus Master transfers

data between the data buffers in RAM and the SIE. The integrated pull-up and pull-down resistors

eliminate the need for external signaling components. The register interface allows the CPU to

configure and communicate with the module.

Note: This family reference manual section is meant to serve as a complement to device

data sheets. Depending on the device variant, this manual section may not apply to

all PIC32 devices.

Please consult the note at the beginning of the “USB On-The-Go (OTG)” chapter

in the current device data sheet to check whether this document supports the device

you are using.

Device data sheets and family reference manual sections are available for

download from the Microchip Worldwide Web site at: http://www.microchip.com

IMPORTANT: The implementation and use of the USB specifications, as well as other

third-party specifications or technologies, may require licensing; including,

but not limited to, USB Implementers Forum, Inc. (also referred to as

USB-IF). The user is fully responsible for investigating and satisfying any

applicable licensing obligations.

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	PIC32MX450F256L

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PIC32MX450F256L stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip HS12-100D0/12DS2F Manual

18 Februar 2025

Microchip HSA0-040SDA/A0SA10 Manual

18 Februar 2025

Microchip HSA0-040SIA/A0S1F Manual

18 Februar 2025

Microchip HT12-100S0s/12ST25 Manual

17 Februar 2025

Microchip EMC2103-2 Manual

17 Februar 2025

Microchip EMC1047 Manual

17 Februar 2025

Microchip HCS201 Manual

17 Februar 2025

Microchip LE9653 Manual

17 Februar 2025

Microchip LAN7430 Manual

17 Februar 2025

Microchip HCS500 Manual

17 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

XO D1HPBF Manual

16 Juni 2025

Fantech RS1 Manual

16 Juni 2025

Playtive IAN 425414 Manual

16 Juni 2025

Playtive IAN 321249 Manual

16 Juni 2025

Playtive IAN 115930 Manual

16 Juni 2025

Aiphone GT-102HB Manual

16 Juni 2025

Playtive HG05516 Manual

16 Juni 2025

Playtive IAN 295154 Manual

16 Juni 2025

Playtive IAN 324362 Manual

16 Juni 2025

Playtive IAN 302521 Manual

16 Juni 2025