Microchip PIC32MX675F512H Manual
Microchip
Ikke kategoriseret
PIC32MX675F512H
Læs gratis den danske manual til Microchip PIC32MX675F512H (45 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Microchip PIC32MX675F512H, eller vil du spørge andre brugere om produktet?
Side 1/45
© 2009-2017 Microchip Technology Inc. DS60001155D-page 35-1
Section 35. Ethernet Controller
This section of the manual contains the following major topics:
35.1 Introduction.............................................................................................................. 35-2
35.2 Ethernet Controller Overview .................................................................................. 35-3
35.3 Status and Control Registers................................................................................... 35-4
35.4 Operation...............................................................................................................35-43
35.5 Ethernet Interrupts................................................................................................. 35-82
35.6 Operation in Power-Saving and Debug Modes ..................................................... 35-87
35.7 Effects of Various Resets....................................................................................... 35-90
35.8 I/O Pin Control ....................................................................................................... 35-91
35.9 Related Application Notes ..................................................................................... 35-92
35.10 Revision History..................................................................................................... 35-93
PIC32 Family Reference Manual
DS60001155D-page 35-8 © 2009-2017 Microchip Technology Inc.
Register 35-1: ETHCON1: Ethernet Controller Control 1 Register
Bit
Range
Bit
31/23/15/7
Bit
30/22/14/6
Bit
29/21/13/5
Bit
28/20/12/4
Bit
27/19/11/3
Bit
26/18/10/2
Bit
25/17/9/1
Bit
24/16/8/0
31:24
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
PTV<15:8>
23:16
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
PTV<7:0>
15:8
R/W-0 U-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0
ON — SIDL — — — TXRTS RXEN
(1)
7:0
R/W-0 U-0 U-0 R/W-0 U-0 U-0 U-0 R/W-0
AUTOFC — — MANFC — — — BUFCDEC
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 31-16 PTV<15:0>: PAUSE Timer Value bits
This register should be written only when the RXEN bit (ETHCON1<8>) is not set. These bits are only used
for Flow Control operations.
bit 15 ON: Ethernet ON bit
1 = Ethernet module is enabled
0 = Ethernet module is disabled
bit 14 Read as ‘Unimplemented: 0’
bit 13 SIDL: Ethernet Stop in Idle Mode bit
1 = Ethernet module transfers are suspended during Idle mode
0 = Ethernet module transfers continue during Idle mode
bit 12-10 Read as ‘Unimplemented: 0’
bit 9 TXRTS: Transmit Request to Send bit
1 = Activate the transmit logic and send the packets defined in the TX Ethernet Descriptor Table (EDT)
0 = Stop transmit (when cleared by software) or transmit done (when cleared by hardware)
After the bit is written with a ‘1 0’, it will clear to ‘ ’ whenever the transmit logic has finished transmitting the
requested packets in the EDT. If ‘0’ is written by the CPU, the transmit logic finishes the current packet’s
transmission, and then stops any further transmission.
This bit only affects TX operations.
bit 8 RXEN: Receive Enable bit
(1)
1 = Enable RX logic, packets are received and stored in the RX buffer as controlled by the filter configuration
0 = Disable RX logic, no packets are received in the RX buffer
This bit only affects RX operations.
bit 7 AUTOFC: Automatic Flow Control bit
1 = Automatic Flow Control is enabled
0 = Automatic Flow Control is disabled
Setting this bit will enable the automatic Flow Control. If set, the full and empty watermarks are used to
automatically enable and disable the Flow Control. When the number of received buffers BUFCNT<7:0> bits
(ETHSTAT<23:16>) rises to the full watermark, Flow Control is automatically enabled. When the BUFCNT
falls to the empty watermark, Flow Control is automatically disabled.
This bit is only used for Flow Control operations, and affects both TX and RX operations.
bit 6-5 Unimplemented: Read as ‘0’
Note 1: It is not recommended to clear the RXEN bit, and then make changes to any RX related field/register. The
Ethernet Controller must be reinitialized (ON cleared to ‘0’), and then the RX changes applied.
Produkt Specifikationer
| Mærke: | Microchip |
| Kategori: | Ikke kategoriseret |
| Model: | PIC32MX675F512H |
Har du brug for hjælp?
Hvis du har brug for hjælp til Microchip PIC32MX675F512H stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Microchip Manualer
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
18 Februar 2025
18 Februar 2025
18 Februar 2025
Ikke kategoriseret Manualer
- NetAlly
- Snow Joe
- Paw Patrol
- Durvet
- Hori
- Elmo
- Domyos
- Echowell
- Manitowoc
- Namco Bandai Games
- Burigotto
- A4 Tech
- SALEX
- SWIT
- LogiLink
Nyeste Ikke kategoriseret Manualer
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025