Microchip USB2227 Manual

Microchip Ikke kategoriseret USB2227

Læs gratis den danske manual til Microchip USB2227 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Microchip USB2227, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Austin Design Center

11000 North Mopac Expressway

Stonelake Bldg. 6 Suite 500

Austin, Texas 78759

EVB-USB2228-CRB Users Guide

Rev. B.1

Updated 2006-12-14

The information contained herein is proprietary to SMSC and shall be used solely in accordance with the agreement

pursuant to which it is provided. Although the information is believed to be accurate, no responsibility is assumed for

inaccuracies. SMSC reserves the right to make changes to this document and to specifications and product

descriptions at any time without notice. Neither the provision of this information nor the sale of the described

semiconductor devices conveys any licenses under any patent rights or other intellectual property rights of SMSC or

others unless specifically specified otherwise. The product may contain design defects or errors known as anomalies,

including but not necessarily limited to any which may be identified in this document, which may cause the product to

deviate from published specifications. SMSC products are not designed, intended, authorized or warranted for use in

any life support or other application where product failure could cause or contribute to personal injury or severe

property damage. Any and all such uses without prior written approval of an officer of SMSC will be fully at the risk of

the customer. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”).

SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST

INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR

USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL,

PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REV-ENUES OF ANY KIND;

REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR

OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS

HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

Evaluation Board: Two-layer EVB-USB2228-CRB - Rev. B.1 Users Guide

Customer Evaluation Board for USB2228 in QFP-128 Package

Features

• Operates either USB Bus-powered or from a single voltage (+5.0V, regulated) ‘wall wart’ external power supply

• Low Cost 2-Layer Space-saving Design

• Supports these Media Types: Compact Flash, Micro Drive, MultiMediaCard, xD picture Card, Smart Media,

Secure Digital, Memory Stick, High Speed Memory Stick, Memory Stick Pro

• Access to up to Four Memory Devices at the same time

• Software Upgradeable through On-Board Flash Socket

• Serial EEPROM capable

• Single Onboard +3.3V Regulator

• Internal FET Power Switching for All Media Types (except CF)

• Single Crystal Clock Source

General Description

The EVB-USB2228-CRB is a platform featuring USB2228 card reader. The board connects to a USB 2.0 port (J1),

and optionally to a 5.0V external supply (J2: 2.1mm, tip -- POS). The board provides four media sockets supporting

at least nine different media types. This board demonstrates a small footprint, low-cost implementation of the

USB2228 with a robust feature set.

The card features an on-board EEPROM for configuration and serial number data, as well as a socket for a Flash

device for firmware updates. The schematics for this board indicate which components are required for each

programming and configuration option.

Power Consumption

These values represent a card with no media installed.

435uA Suspended

55mA Enumerated (Active and Idle)

Jumper Descriptions

ROMEN: J30 Jumper pins 1 & 2 to enable the Flash installed at U30.

Power Select: J3 Jumper pins 1 & 2 to select Bus Powered mode (USB-supplied power).

Jumper pins 2 & 3 to select Self Powered mode (externally-supplied 5.0V).

IrDA: J4 This connector is not used with the USB2228 device. This 6-pin header is provided to

support the USB2230 device.

SMSC 2 12/14/2006

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	USB2227

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip USB2227 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip AT7913 Manual

1 September 2025

Microchip ATmega1281 Manual

19 Juli 2025

Microchip ATtiny461 Manual

19 Juli 2025

Microchip ATxmega128D3 Manual

19 Juli 2025

Microchip ATxmega128D4 Manual

19 Juli 2025

Microchip ATTINY28 Manual

19 Juli 2025

Microchip ATTINY861 Manual

19 Juli 2025

Microchip ATmega1280 Manual

19 Juli 2025

Microchip ATtiny84A Manual

19 Juli 2025

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock PT44 Manual

14 September 2025

BSS Audio FDS-366T Manual

14 September 2025

Systemair Airline R-114 Manual

14 September 2025

IFM SU2031 Manual

14 September 2025

Morel Tempo Ultra Integra 502 Manual

14 September 2025

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025