Mikrotik PWR-LINE US Manual

Mikrotik Powerline adapter PWR-LINE US

Læs gratis den danske manual til Mikrotik PWR-LINE US (4 sider) i kategorien Powerline adapter. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Mikrotik PWR-LINE US, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
PWR-LINE
The PWR-LINE series devices allow Ethernet like connectivity between supported devices over regular electrical
power lines. When plugged into the same electrical circuit, the PWR devices will establish Ethernet connectivity by
using the HomePlug AV standard.
The PWR-LINE is a smart power adapter with a built-in USB cable.
This particular device is designed for supported MikroTik products with a microUSB port and PWR-LINE support.
Connect this adapter to your electrical outlet and then connect the USB cable to power your supported MikroTik
device. When doing the same with another PWR-LINE compatible device somewhere further in your premises, the
devices will form a connection without needing to install any LAN cables. The device will show up as an additional
Ethernet interface in your routers configuration interface. You can install more PWR-LINE devices to further build
your network.
Connecting
1. Plug one PWR-LINE device into a power socket.
2. Connect the built-in USB cable to the microUSB port of a supported MikroTik router.
3. Plug another PWR-LINE unit (or any other compatible device) somewhere in the same electrical circuit.
Use the sync button to connect the devices and your local network will automatically be extended. See
section Buttons and Jumpers on how to pair additional PWR-LINE devices.
Powering
The device accepts powering directly from 100-230 V ~50/60Hz wall socket it is plugged into. The power
consumption under maximum load can reach 5 W.
Buttons and Jumpers
PWR connection button (sync)
•Hold 0.5 – 3 seconds. For 120 seconds will try to communicate with another PWR-LINE device. A blinking
orange LED light indicates that it is in search mode. You have to also do the same on the other PWR
device, so they can synchronize. Press button again to cancel the search.
•Hold 5 – 8 seconds. A new security key is generated. This is needed to remove a PWR-LINE device from
an existing PWR network.
•Hold 10 – 15 seconds. Resets all PWR related settings.
See for more information. Contact for help. Modified: 11-Feb-19 Document #45868https://mikrotik.com support@mikrotik.com
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.This device and its antenna must not be co-located or operation in
conjunction with any other antenna or transmitter.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
See for more information. Contact for help. Modified: 11-Feb-19 Document #45868https://mikrotik.com support@mikrotik.com

Produkt Specifikationer

Mærke: Mikrotik
Kategori: Powerline adapter
Model: PWR-LINE US

Har du brug for hjælp?

Hvis du har brug for hjælp til Mikrotik PWR-LINE US stil et spørgsmål nedenfor, og andre brugere vil svare dig


Powerline adapter Mikrotik Manualer

Mikrotik

Mikrotik PWR-Line AP Manual

20 September 2024
Mikrotik

Mikrotik PWR-LINE US Manual

25 August 2024
Mikrotik

Mikrotik PL7510Gi Manual

7 August 2024

Powerline adapter Manualer

Nyeste Powerline adapter Manualer

Act

Act AC4470 Manual

20 Februar 2025
D-Link

D-Link DHP-W306AV Manual

1 Februar 2025
Netgear

Netgear XAV5601 Manual

12 Januar 2025
AVM

AVM FRITZ!Powerline 510E Set Manual

30 December 2025
AVM

AVM FRITZ!Powerline 1220 Set Manual

30 December 2025
D-Link

D-Link DHP-329AV Manual

29 December 2024
D-Link

D-Link DHP-P307AV Manual

23 December 2024
D-Link

D-Link DHP-W307AV Manual

23 December 2024
D-Link

D-Link DHP-310AV Manual

19 December 2024
D-Link

D-Link DHP-307AV Manual

19 December 2024