Mitsubishi Line-Hide CD-100 Manual

Mitsubishi Ikke kategoriseret Line-Hide CD-100

Læs gratis den danske manual til Mitsubishi Line-Hide CD-100 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Mitsubishi Line-Hide CD-100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION INSTRUCTIONS

& BEAUTIFY

PROTECT

&BEAUTIFY

PROTECT

No. LIOCA 100710M

WWW.LINE-HIDE.COM

Distributed by

MITSUBISHI ELECTRIC

Perfect for and other A/C and plumbing applications and installations.

Installing Line-Hide

Your Line-Hide installation will go smoothly if you follow — in

order

— the steps outlined in these instructions: determine lay-

out; install entry fittings and joint bases; install Line

Tube base;

insert Lineset: assemble tube, and assemble joints. When

you’ve finished, caulk the lineset entry and exit points on the

wall to ensure the protection of the Lineset and of the building.

Step 1: Layout

Identify the inlet and out-

let points for the Lineset

you’ll be installing within the Line-Hide

product, and determine the simplest

and most appropriate route for the

installation to follow. In most cases you’ll want your installation

to run perfectly vertical and nearly horizontal (a slight grade will

enable condensate lines to drain) and adhere to 90 degree

turns. Sketching your installation on a contractor worksheet or

graph paper will help you to determine how much tubing and

how many elbows, joints, and other pieces you will need.

Step 2: Install Entry Fittings and Joint Bases

Most Line-Hide entry fittings and joints (including elbows)

include a base and a cover. Once you’ve determined where

your joints will be, install the bases. If you’re installing on wood,

simply position the base, and fasten it to the wall, using wood

screws. Don’t overtighten, or you’ll risk cracking the plastic.

For installations on a brick wall, mark the location for

each screw, and drill an anchor hole

using a masonry bit; then use

appropriate anchors and

screws.

Step 3:

Install Line

Tube Base

Measure the distance between the molded stops of each joint

base, and determine the length of tube needed. Line-Hide Line

ube is manufactured in six-and-one-half-foot (two-meter)

lengths so some straight runs are fabricated using two or more

lengths of tube and a socket/coupling.

cut tube, measure and mark

the appropriate length;

then draw a perpendicu

lar guideline across the

tube. Use a hacksaw to cut

the tube along the line, and

then use a file to smooth the

cut edge.

INSTALLATION INSTRUCTIONS

WARNING! Before you begin . . .

Whenever you’re working with tools, it’s a good idea

to wear appropriate safety gear: helmet, protective goggles, and gloves. If

you’re working high above the ground, be sure that you have sound footing.

To attach the Line Tube

base to the wall, first use

the tip of a screwdriver to

make a hole in the central

rib of the base (thin spots

are moulded in to accommodate installation). Then put a screw

through the hole in the tube, and tighten it to the wall. Be care-

ful not to overtighten, for you may distort the tube. For the

smaller sizes (the 60 and 75 series), place screws approximate-

ly every twelve inches. For the larger sizes (the 100 and 140

series), use screws approximately every six inches.

Step 4: Install the Lineset

Unwind insulated refrigerant lines, and place into straight portion

of the tube. When installing insulated refrigerant pipe into a cor-

ner, adjust the pipe to the shape of the joint, and gently bend the

insulated refrigerant pipe without forcing it. Bending too quickly

can cause kinks in insulated refrigerant pipe and can pinch drain

pipe. Also try to avoid compressing the pipe insulation.

A Saddle Band (NV-S short or

NV-L long) can be used to fas-

ten the insulated refrigerant

pipe, drain pipe, and electric

cable together in the Line

Tube. The saddle snaps to the

central rib of the tube base.

Thread the band through the

saddle and around the piping and cable, and pull it tight. This pro-

cedure will help to keep the pipes and wiring in place.

As a general rule, use one saddle band for every three feet (one

meter) of tube.

Step 5: Assemble

the Line

ube

When the Lineset is in

position, attach the tube

cover to the base. Slip

the lip on the short

edge of the cover into the trough on the high edge of the base.

Then squeeze the short end of the base while pushing the long

edge of the cover inward so that the lip and the trough engage.

Step 6: Assemble the Joints

With the Line Tube completely assembled, return to each joint,

and complete assembly

. Position the cover of each joint over its

base; line up the holes; then secure cover to bases with the

stainless steel screws provided.

Try to adhere to a grid defined

by parallel and perpendicular

lines and 90-degree angles

Produkt Specifikationer

Mærke:	Mitsubishi
Kategori:	Ikke kategoriseret
Model:	Line-Hide CD-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Mitsubishi Line-Hide CD-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Mitsubishi Manualer

Mitsubishi Line-Hide CD-100 Manual

7 Juni 2025

Mitsubishi Line-Hide NE-100 Manual

7 Juni 2025

Mitsubishi Line-Hide CD-140 Manual

7 Juni 2025

Mitsubishi WB-PA3 Manual

6 Juni 2025

Mitsubishi HMS100-W Manual

5 September 2024

Mitsubishi HMA60-W Manual

5 September 2024

Mitsubishi HMA100-W Manual

5 September 2024

Mitsubishi PZ-70CSW-E Manual

3 September 2024

Mitsubishi PZ-70CSD-E Manual

3 September 2024

Mitsubishi 9900D Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

SilentiumPC Ventum VT2 Manual

25 Juli 2025

Xiaomi Redmi 13R Manual

25 Juli 2025

Zoom Tri Metal TM-01 Manual

25 Juli 2025

Taga Harmony HTR-1000CD Manual

25 Juli 2025

Aiphone ACS-IO Manual

25 Juli 2025

Aiphone AC-PS1250 Manual

25 Juli 2025

MikroElektronika EasyPIC PRO v7 Manual

25 Juli 2025

Ikea JUTEBODA 805.570.71 Manual

25 Juli 2025

Atlas Sound ECM-20SH Manual

25 Juli 2025

MSW -ISU-STYRO 250 S4 Manual

25 Juli 2025