Mitsubishi RC-MCU-E Manual


Læs gratis den danske manual til Mitsubishi RC-MCU-E (47 sider) i kategorien Varmepumpe. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Mitsubishi RC-MCU-E, eller vil du spørge andre brugere om produktet?

Side 1/47
REMOTE CONTROL
RC-MCU-E
USER'S MANUAL
Thank you very much for your purchasing the REMOTE CONTROL for our
heat pump chiller.
This user's manual describes cautions for safety. Please read this manual carefully before use in order to operate the unit properly.
Keep this manual, after reading, at a safe place where you can consult it whenever it is necessary.
When the ownership of the unit is changed, please be sure to transfer this manual and the “Installation Manual” to a new owner.
It is not recommended for a user to install or move the unit by the user's own discretion. (Safety or functions may not be assured.)
This air to water heat pump complies with Machinery Directive 2006/42/EC, EMC Directive 2014/30/EU, Pressure Equipment Directive
2014/68/EU, RoHS Directive 2011/65/EU, (EU) 2015/863, Ecodesign requirement Directive 2009/125/EC.
PJZ012A228
202308
ORIGINAL INSTRUCTIONS
1
Note
Please turn on the power switch
6 hours before operation to
protect the heat pump chiller
(the crank case heater is
conducted and the compressor
is heated).
Also, be sure not to turn o
the power switch (the crank
case heater is conducted and
the compressor is heated
during stop of the compressor.
It protect the fault of the
compressor caused by liquid
refrigerant stagnation).
Contents
1. Before you use.................................. 2
1.1 Safety precautions ..................................................... 2
1.2 Precautions for waste disposal .................................. 3
1.3 Unit speci cations ...................................................... 3
1.4 Names and functions of sections on the R/C ............. 4
2. Initial settings ................................... 6
2.1 Unit settings ............................................................... 6
2.2 R/C initial settings ...................................................... 7
3. Running status setting ..................... 9
3.1 When using the schedule function ............................. 9
3.2 When not using the schedule function ..................... 22
3.3 When monitoring the operation status ..................... 25
3.4 For the C/H mix mode system ................................. 26
4. Other settings ................................. 31
4.1 Peak-cut timer settings ............................................ 32
4.2 Administrator settings .............................................. 34
4.3 R/C settings ............................................................. 38
4.4 Service & Maintenance setting ................................ 39
4.5 Initial settings ........................................................... 42
4.6 Installation settings .................................................. 44
4.7 Select language ....................................................... 46


Produkt Specifikationer

Mærke: Mitsubishi
Kategori: Varmepumpe
Model: RC-MCU-E

Har du brug for hjælp?

Hvis du har brug for hjælp til Mitsubishi RC-MCU-E stil et spørgsmål nedenfor, og andre brugere vil svare dig




Varmepumpe Mitsubishi Manualer

Varmepumpe Manualer

Nyeste Varmepumpe Manualer

Hotpoint

Hotpoint 1H12HN2DAA Manual

11 September 2025
Hotpoint

Hotpoint 1H18HN2DAA Manual

11 September 2025
Electrolux

Electrolux TD6-20 Manual

9 September 2025
Electrolux

Electrolux TD6-7 Manual

9 September 2025
Electrolux

Electrolux TD6-11 Manual

9 September 2025
Wolf

Wolf CWL-T-300 Manual

8 September 2025
LG

LG LSU180HSV5 Manual

4 September 2025
Daikin

Daikin FWXV15AATV3 Manual

3 September 2025
Daikin

Daikin FWXV15ABTV3 Manual

3 September 2025