Mobotix MX-M16A-6D6N041 Manual

Mobotix Overvågningskamera MX-M16A-6D6N041

Læs gratis den danske manual til Mobotix MX-M16A-6D6N041 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 33 anmeldelser. Har du et spørgsmål om Mobotix MX-M16A-6D6N041, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

M16 AllroundDual

Quick Install

32.845-005_EN_04/2018

Standard Delivery M16

1.1

1.10

1.11

1.12

1.8

1.7

1.4 1.3

1.6

1.9

1.2

1.5

M.5

M.3

M.2

M.1

M.6

M.7

M.8

M.10

M.11

M.4

1.15

1.19

1.16

1.17

M.9

1.18

1.20 1.13

1.14

Standard Delivery

Item Count Part Name

1.1 1 Camera housing with mainboard and wall mount (installed),

without sensor modules and front element

1.2 1 Front element with additional sensors (installed)

1.3 2 Transport plugs (installed)

1.4 1 Blind module (must be installed when using only one sensor

module)

1.5 4 Inner housing cover (installed)

1.6 4 Stainless steel Allen screw with at head M4x8 for inner housing

cover (installed)

Standard Delivery

Item Count Part Name

1.7 2 Cable lock black with bayonet catch (Ethernet patch cable, USB,

one installed, one supplied)

1.8 2 Single wire plug, blue ( USB, installed)MxBus,

1.9 1 MicroSD card (SDXC, SDHC pre-installed)

1.10 1 Ethernet patch cable, 50 cm/19.7 in with sealing (installed)

1.11 2 Sensor module cable 15 cm/6 in (installed in camera)

1.12 1 I/O cable with red clips to front element 15 cm/6 in (installed)

1.13 1 Hinged ferrite for Ethernet cable (installed)

1.14 1 Hinged ferrite for sensor module cable (installed)

1.15 2 Rubber plug for covering mounting screws, white

1.16 3 Stainless steel Allen screw M6x30 (installed)

1.17 3 Stainless steel washer dia. 6.4 mm (installed)

1.18 1 Stainless steel spring washer dia. 6.4 mm (wall/ceiling mount,

installed)

1.19 1 Stainless steel lock nut M6 (wall/ceiling mount, installed)

1.20 1 Rubber plug, black (installed)

Mounting Supplies

Item Count Part Name

M.1 4 Stainless steel washer dia. 6.4 mm

M.2 4 Dowels 8 mm

M.3 4 Stainless steel wood screw with hex head 6x50 mm

M.4 1 Allen wrench 2.5 mm

M.5 1 Allen wrench 5 mm

M.6 1 Lens wrench (SMA-S-6D/N/L016 lens, glass/lter insert, dome)

M.7 1 Module key (sensor module, focusing of lenses)

M.8 1 Rubber sealing for wall/ceiling mount, white

M.9 1 Ceiling mount for VarioFlex mount

M.10 4 Protection cover for screw, white

M.11 4 Security clip for sensor or blind modules, red

Opening/Closing the Camera Housing

The following tasks require opening the camera housing and removing the front element of the M16 in order to get to the interior of the camera:

Inserting the security clips, exchanging the Ethernet patch cable, connecting the two-wire lineMxBus , connecting the USB cable, exchanging the MicroSD

card (see also «Inserting/Exchanging the SD Card» on page 2).

CAUTION: Make sure the power supply to the camera is disconnected before opening the housing!

1. Opening the Camera Housing

Place the camera face-down on a clean and dry surface. Remove the two

rubber plugs at the back of the camera housing. Using the supplied 5 mm

Allen wrench, loosen the two bolts at the back of the camera housing.

Leave the bolts and washers in the camera housing.

Using the Allen wrench, push from behind

cautiously in an alternating

fashion onto the le and the right bolt 1 and push the front element

out of the front of the housing.

Tilt the front element forward as shown in the gure 2.

2. Inserting the Security Clips

To protect the modules against unwanted removal, insert the two red

security clips at the insides of the sensor modules at the proper location

(1 inserted, 2 locked). Make sure that the security clips are properly

locked in their seatings 3.

3. Closing the Camera Housing

Before inserting the front element, make sure that the sensor module cables

of both image sensors are running at the of the screw bore inside 1.

Place the camera on its right side (as seen by the camera) as shown and

insert the front element. When pushing the front element into the housing

(2, red arrows), take care not to crush any cables.

When inserting and closing the front element, take special care to guide

the cable of the le sensor module under the rubber hook 3!

Press the front element into the camera housing by evenly applying pres-

sure 4. Tighten the screws with washers.

Finally, apply the rubber plugs at the back of the housing that you removed

earlier.

Preparing the M16 for Installation

To facilitate the installation of the camera, you should complete the following tasks before actually installing the camera.

1. CAUTION!

• Only exchange sensor modules when powered o!

• When operating the camera with only one sensor module, always

install the supplied blind module. No operation with transport plugs!

•

Thermal sensor modules are always pre-installed and cannot be removed!

2. Installing the Sensor Modules

Remove the plastic nut from the sensor module

. Remove the transport

plugs 2.

Push the sensor module cable plug into the connector at the back of the

module housing 3. Secure the plug using the blue bayonet catch as

shown 4.

Insert the sensor module. Make sure that the MOBOTIX lettering on the

sensor module is at the “9 o'clock” position as shown in the gure 5 .

Place the back of the black module wrench onto the two holes of the

sensor module 6.

Using the black module wrench, turn the sensor module clockwise until

it stops 7. If desired, insert the two security clips 8. Open the camera

housing as described in «Opening/Closing the Camera Housing».

M16 with one blind module:

Unrestricted operation

(IP66)

M16 with two transport

plugs:

No operation allowed!

M16 with one transport

plug:

No operation allowed!

Sensor Modules of the M16 (to Be Ordered Separately, Thermal Sensor Pre-Installed)

Protective

glass insert

Plastic nut

Sensor module

SMA-S-6D/N/L036–237

Lens cover

Sensor module

SMA-S-6D/N/L500

Top (markings)

Sensor module cable

Rear

(all except Thermal)

Dome

Plastic nut

Sensor module

SMA-S-6D/N/L016

Connections and Initial Operation of the M16

You can nd detailed information on the installation connections and of the M16 in the M15 Camera Manual (PDF, available on www.mobotix.com >

Support > Download Center > Documentation > Manuals).

Please note that the position of the SD card holder has changed (see gure below, at the right), the boot options of this camera have changed compared

to its predecessor (see «Boot Options of the M16» on page 2) and the camera only has one key ("L").

Regarding the rest of the initial operation of the M16, please see the M15 Camera Manual in Chapter 3, «Initial Operation». The rst access follows the

procedure described in the same manual in the section «Initial Operation of the Camera». All other tasks require access to the camera’s user interface in

the browser. Enter the camera’s IP address into the address bar of the browser (user "admin", password "meinsm"; password must be changed upon rst

Sensor module R

Ethernet

Sensor module LUSB

Slot for MicroSD card

Camera housing

Sensor mod-

ules

LEDs

PIR sensor

Wall Mount

Key L

Front element I/O cable to front

element (red clips)

Ethernet patch cable

Sensor mod-

ules

USB

Front element

MxBus

Sensor Module Combinations

Mx-M16A/B*

2 optical

Day/Night/LPF

Mx-M16A/B*

1 optical

Day/Night/LPF

Mx-M16A/B*

1 Thermal/Thermal-TR,

1 optical Day/Night/LPF

*Variant Mx-M16B MxBus supports MOBOTIX modules

Produkt Specifikationer

Mærke:	Mobotix
Kategori:	Overvågningskamera
Model:	MX-M16A-6D6N041
Kode for international beskyttelse (IP):	IP66
Type:	IP-sikkerhedskamera
Bredde:	158 mm
Dybde:	207 mm
Højde:	210 mm
Vægt:	1400 g
Produktfarve:	Hvid
USB-port:	Ja
Formfaktor:	Terning
Indbyggede højttaler(e):	Ja
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Understøttede videoformater:	H.264, M-JPEG, MxPEG
Strømforbrug (typisk):	5 W
Driftstemperatur (T-T):	-40 - 60 °C
Maksimal opløsning:	6148 x 2048 pixel
Intern hukommelse:	1024 MB
Hurtig installationsvejledning:	Ja
Kabler inkluderet:	LAN (RJ-45)
Understøttede grafikopløsninger:	1280 x 960,1920 x 1080 (HD 1080),2048 x 1536 (QXGA),2592 x 1944
Forbindelsesteknologi:	Ledningsført
Certificering:	EN55032:2012\nEN55022:2010; EN55024:2010; EN50121-4:2015\nEN61000-6-1:2007; EN 61000-6-2:2005\nEN61000-6-3:2007+A1:2011\nEN61000-6-4:2007+A1:2011\nAS/ NZS CISPR22:2009+A1:2010\nCFR47 FCC part15B
Kabelteknologi:	10/100/1000Base-T(X)
Understøttede netværksprotokoller:	Pv4, IPv6, HTTP, HTTPS, FTP, FTPS, RTP, RTSP, UDP, SNMP, SMTP, DHCP (client and server), NTP (client and server), SIP (client and server) G.711 (PCMA, PCMU), G.722
Strømkilde type:	PoE
Monteringstype:	Loft/væg/pæl
Full HD:	Ja
Understøttet placering:	Indendørs & udendørs
Indbygget mikrofon:	Ja
Sensortype:	CMOS
Samlet antal megapixels:	6 MP
Digital zoom:	8 x
Grænseflade:	RJ-45
Processormodel:	i.MX 6
Progressiv scanning:	Ja
Flashhukommelse:	512 MB
Strøm over Ethernet (PoE):	Ja
Dag/nat funktion:	Ja
IK kode:	IK04
Vandafvisende:	Ja
Minimumsbelysning:	0.005 Lux
Optisk sensorstørrelse:	1/1.8 "
Antal effektive pixels (HxV):	3072 x 2048 pixel
Zoom kapacitet:	Ja
Fast brændvidde:	4.1 mm
Nattesyn:	Ja
Billedhastighed:	42 fps
Antal kameraer:	1
Monteringssæt:	Ja
Bevægelsessensor:	Ja
Objektivtype:	Ultra vidvinkel
Streaming metode:	Multicast
PTZ-kontrol:	Ja
Skruer inkluderet:	Ja
Støjregistrering:	Ja
Advarsel notifikationstype:	Snapshot alert message, Text alert message
Temperaturføler:	Ja
Prøvetagningshastighed:	16 kHz
Hukommelseskort inkluderet:	MicroSD
Inkluderet hukommelseskort størrelse:	4 GB
Objektivets synsvinkel, vandret:	90 °
Objektivets synsvinkel, lodret:	67 °
PTZ-tilstande:	Digital PTZ
Bevægelsessensor teknologi:	Passiv infrarød (PIR) sensor