Muse M-180CR Manual

Muse Clockradio M-180CR

Læs gratis den danske manual til Muse M-180CR (2 sider) i kategorien Clockradio. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Muse M-180CR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Battery backup system

DC power: 9V battery type 6F22 (not provided) for clock and alarm time backup system

only.

An alkaline type battery is recommended. For optimum performance this battery should

be replaced every 6 months.

Note: if no battery is installed or if the battery is low, “ ” indicator is displayed (2).

Connect the 9V battery inside the compartment (14) at the back of the unit.

BACKUP SYSTEM: Ensures that the unit continues to operate during an AC power

disruption (in order to preserve the battery life, the display is switched off). All clock,

date and alarm settings will be kept in the memory, however, the clock time may

require adjustment for exact accuracy. If no battery is installed, the display will blink to

indicate that you have to reset the time and alarm.

1. Slide the SETTING mode switch (19) to CLOCK position, press / (10) to

select the time mode between 12hours and 24hours, press DATE/SET (5) to confirm .

Then the hour digits will flash, press / (10) to adjust the value. The time

decrements or increments at a faster rate when you press and hold the buttons. Confirm

with DATE/SET (5). Repeat this procedure for the minute, year, sequence (D-M or M-

D) and value of day (“D”) and month (“M”)

1. ON/OFF button

2. LCD display

3. ALM.1 button

4. ALM.2 button

5. DATE/SET button

6. NAP button

7. SLEEP button

8. Speaker

9. Projector

10. SNOOZE/ / button

11. Projector ON/OFF switch

SETTING THE TIME

GB - 1 GB - 2

GB - 4GB - 3

INDOOR / OUTDOOR TEMPERATURE

GB - 5

M-180CR

User Manual

In/Out temperature projection clock radio

PLEASE READ THE INSTRUCTION CAREFULLY

BEFORE OPERATING THE UNIT

English

UNPACKING YOUR UNIT

When you unpack your new clock radio, make sure that you have removed all the

accessories and information papers:

- Projection clock radio

- AC/DC adaptor

- External temperature remote sensor with transparent cover and wall bracket

- User manual

PRODUCT DESCRIPTION

Location of controls

12. ROTATE button (for projected

image)

13. ºC / ºF button

14. Battery backup compartment

15. 5V DC in jack

16. Volume control

17. Band selector: MW/FM

18. Tuning knob

19. SETTING mode selector: CLOCK/

ALM.1/ALM.2/LOCK

20. FM wire antenna

21. Indoor temperature sensor

LCD display

POWER SUPPLY

AC/DC adaptor

- The supplied AC/DC adaptor is suitable

for use on AC mains supplies of 230V~

50Hz and should only be connected to a

mains supply with these parameters.

Caution:

- The included AC/DC adaptor is for use

with this unit only. Do not use it with other

equipments.

- When the unit is not going to be used for

long time, disconnect the AC/DC adaptor

from the AC outlet.

- Be sure to use it near the wall outlet. If a

malfunction occurs, disconnect the plug

from the wall outlet at once.

- When the AC/DC adaptor is plugged in, the apparatus is not completely disconnected

from the main power source, even when the unit is turned off.

- The AC/DC adaptor shall not be exposed to dripping or splashing and that no objects

filled with liquids, such as vases, shall be placed on apparatus.

- To be completely disconnect the power input, the AC/DC adaptor of apparatus shall

disconnected from the mains.” as the disconnect devices is the AC/DC adaptor of

apparatus.

- The AC/DC adaptor of apparatus should not be obstructed OR should be easily accessed

during intended use.”

Note: Pressing DATE/SET button (5) again, enters a new setting cycle.

Once the unit is plugged in, it will enter the time setting mode. ”24Hr” blinks on display.

2. Slide the SETTING mode switch (19) to LOCK position. The calendar is viewed for

3 seconds and display resumes to clock mode.

Pressing DATE/SET (5) displays the calendar for 3 seconds

Indoor temperatare

Once the unit is connected, the indoor temperature is displayed (2).

Celsius (ºC) and Fahrenheit (ºF).degrees selection

The button (13) switches the unit for both indoor and outdoor temperature

between Celsius (ºC) and Fahrenheit (ºF) degrees.

Outdoor temperature

1. Remote sensor set-up

- Remove the wall bracket.

- Unlock two latches at the bottom to release the transparent cover.

- Slide down the battery door at the back.

- Insert 2 batteries, type R03/UM4/AAA (not provided). Follow the polarity indicated in

the battery compartment

- An alkaline type battery is recommended. For optimum performance this battery should

be replaced every 6 months.

2. Remote sensor synchronization

- To enter synchronization mode, press and hold (10) for 3 seconds on the main

unit, “ ” flashes on the display (2) for 2 minutes.

- Press RESET button of the remote sensor with pointed object (such as ball-point

pen). The LED blinks

- A few seconds later the temperature will appear on the display of the main unit.

- To exit synchronization mode, press button (10), “ ” is not displayed.

Note:

* To synchronize remote sensor and main unit on a different channel, press CH button

and repeat synchronization operations.

* Once connected, the unit enters in synchronization mode with the remote sensor for

2 minutes. “ ” flashes on the display.

3. Replace battery door and transparent cover, lock the 2 latches at the bottom. Install

the remote sensor within a range of 50 meters from main unit in open area.

4. “ ”on the outdoor temperature area of the display, indicates that the remote

sensor batteries are low. Replace them with new batteries.

After battery replacement, or after main unit reset, or if the sensor is under the influence

of electrical fast transient or/and electrostatic phenomenon, reset the remote sensor

with the RESET button.

Note:

* If the unit fails to received the outdoor temperature for ,10 minutes it will display

“ - - . - “ .

* Displayed temperature and remote sensor operating range: -10.0°C to +60.0°C (+14.

0°F to +140.0°F)

未命名－１ 2009-9-8, 16:171

- ON/OFF (1): Press to stop the alarm and it will sound again 24 hours later. “ ”/

“ ” or “ ”/“ ” are still shown on the display.

3. Alarm 2 settings

Same operations as for Alarm 1: SETTING mode switch (19) to ALM.2 for the time

setting and ALM.2 (4) button for alarm mode.

Note:

If the radio is ON at the wake-up time, regardless the alarm source is radio or buzzer,

the alarm will be triggered with buzzer tone and the radio will be mute. If alarm is

stopped, the radio is resumed.

4. Alarm stop

The alarm is programmed to run for 1 hour and 59 minutes.

Once the alarm 1 or alarm 2 is activated, corresponding alarm indicator with brackets

“ ”/” ” or “ ”/” ” flashes on display.

This unit allows to set two different wake-up times.

1. Alarm 1 time set

Slide the SETTING mode switch (19) to ALM.1 position. Press / (10) to set the

wake time, then press DATE/SET (5) to confirm. Set the hours first, then the minutes.

GB - 10

GB - 6 GB - 7

NAP FUNCTION

THE ALARM AND WAKE-UP MODE

GB - 8

GB - 9 GB - 11

When alarm 1 setting is completed, slide the SETTING mode switch (19) to LOCK

position

Note: To check the alarm 1 time, you can press and hold the ALM.1 button (3) for 4

seconds when the SETTING switch (19) is on LOCK position (the alarm 1 time is

displayed for 3 seconds) or switch the SETTING mode switch to ALM.1 position

2. Alarm 1 mode (buzzer or radio selection)

When the SETTING switch is on LOCK position, press ALM.1 button (3) repeatedly to

switch among wake up by buzzer, radio or alarm off.

1st press: “ ” alarm by buzzer

2nd press:” ” alarm by radio

3rd press: alarm off, no icon displayed

- SNOOZE (10): Press to stop the alarm temporarily, the alarm will ring again when the

snooze period is over. “ ”/“ ” or “ ”/“ ” flashes on display.

To adjust the snooze period (up to 30 minutes, the default time is 9 minutes), press and

hold SNOOZE (10) for 5 seconds, the snooze time blinks on the display, press or

(10) to adjust the value, It will return to clock display if no key is pressed within 5

seconds, the snooze time is stored.

Note: Pressing ON/OFF (1) to stop the alarm will not affect the current status of the

radio.

- ALM. 1 or ALM. 2 (3 or 4): press to turn off the alarm permanently, the alarm

indicator “ ”/ “ ” or “ ”/“ ” are not shown on the display.

This function wakes you up after a short period of time. Only buzzer sound can be

selected for NAP.

1. Press and release the NAP (6) button. The “NAP” icon and the current nap time

flashes on display (2). During this period, adjust nap time by pressing or (19).

Note: The nap range is from 10 minutes to 2 hours. (The default time is 20 minutes)

2. Press NAP (6) to confirm nap time. If no button is pressed during 5 seconds, it will

return to clock display with NAP icon.

3. When the Nap alarm is triggered, press NAP (6) or ON/OFF (1) to stop, “NAP” icon

will disappear.

4. To cancel NAP function before NAP alarm is triggered, press and hold NAP button

(6), the “NAP” icon will blink for two seconds then go off. Release the NAP button.

SLEEP FUNCTION

In sleep mode, radio will turn off automatically after a specified time.

1. To set the sleep time, press and hold SLEEP button (7), at the same time press or

(19) to adjust the value. The time decrements or increments will follow by a faster

rate when you press and hold or button. Release SLEEP (7), your setting is

stored in memory. The sleep time range is from 1 to 120 minutes.

2. The radio is turned on after setting Sleep Time. The radio will turn off when the

preset time elapses. The “SLEEP” icon will be off.

3. If you want to turn off the radio before the SLEEP activates, press ON/OFF button.

The sleep function will be cancelled, “SLEEP” icon will be off.

IMPORTANT SAFETY INSTRUCTIONS

ATTENTION: To reduce the risk of electric shock, do not

remove the cover. There are no user serviceable parts inside

the unit. Refer all servicing to qualified personnel.

The lightening flash with arrowhead symbol within the triangle is a warning

sign alerting the user of “dangerous voltage” inside the unit.

The exclamation point within the triangle is a warning sign alerting the user of

important instructions accompanying the product.

WARNING

- Do not throw batteries in fire!

- Do not mix different types of batteries or old batteries with new ones.

- Never recharge the batteries, apply heat to them or take them apart.

- Attention should be drawn to the environmental aspects of battery disposal.

- Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

- The marking information is located at the bottom of apparatus.

- Ensure a minimum distance of 5cm around the apparatus for sufficient ventilation.

- Ensure that the ventilation is not impeded by covering the ventilation openings with

items, such as newspapers, table-clothes, curtains, etc.

- Do not place naked flame sources, such as lighted candles on the apparatus.

- Use the apparatus only in moderate climates.

- Do not be exposed to dripping or splashing. And that no object filled with liquids, such

as vases, shall be placed on the apparatus.

- Do not use your set immediately after transport from a cold place to a warm place,

there may be condensation problems.

- Make sure that you keep your set away from water and high temperatures.

- Clean the player with a soft cloth, or damp chamois leather. Never use solvent.

- Under the influence of electrical fast transient or/and electrostatic phenomenon, the

product may malfunction and require user to power reset.

If at any time in the future you should need to dispose of this product please

note that Waste electrical products should not be disposed of with household

waste. Please recycle where facilities exist. Check with your Local Authority

or retailer for recycling advice.(Waste Electrical and Electronic Equipment

Directive)

THE TIME PROJECTION

1. Turn on or off the projector with the ON/OFF switch (11) at the back of the projector.

2. Rotate the projected time by 180º with the ROTATE button (12) at the back of the

projector.

3. Swivel the projector to move the projected time.

LISTENING TO THE RADIO

1. Press ON/OFF (1) to turn on the radio, press this button again to turn it off.

2. Switch to FM or MW with the Band selector (17).

3. Select a radio station with tuning knob (18). The frequency is displayed (2) for a few

seconds. Then it returns to clock mode

4. Adjust the volume (16) to the desired level.

5. For a better reception, in FM extend the antenna (20); in MW rotate the unit.

未命名－１ 2009-9-8, 16:212

Produkt Specifikationer

Mærke:	Muse
Kategori:	Clockradio
Model:	M-180CR
Vekselstrømsindgangsspænding:	230 V
Vekselstrømsindgangsfrekvens:	50 Hz
Bredde:	74 mm
Dybde:	166 mm
Højde:	122 mm
Vægt:	350 g
Antal pr. pakke:	1 stk
Brugervejledning:	Ja
Produktfarve:	Sort
Skærmtype:	LCD
Pakkevægt:	850 g
Pakkedybde:	192 mm
Pakkebredde:	85 mm
Pakkehøjde:	168 mm
Indbyggede højttaler(e):	Ja
Slumretimer:	Ja
Kalender:	Ja
Termometer:	Ja
Strømkilde:	Vekselstrøm
DC-in-stik:	Ja
AC-adapter inkluderet:	Ja
Baggrundsfarve:	Blå
Antal indbyggede højttalere:	1
Vækkeur:	Ja
Baggrundslys:	Ja
Lydalarm:	Ja
Alarmfunktion:	Ja
Snooze funktion:	Ja
Projektion, funktion:	Tid