Muse M-180CRW Manual

Muse Clockradio M-180CRW

Læs gratis den danske manual til Muse M-180CRW (2 sider) i kategorien Clockradio. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Muse M-180CRW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Battery backup system

DC power: 9V battery type 6F22 (not provided) for clock and alarm time backup system

only.

An alkaline type battery is recommended. For optimum performance this battery should

be replaced every 6 months.

Note: if no battery is installed or if the battery is low, “ ” indicator is displayed (2).

Connect the 9V battery inside the compartment (14) at the back of the unit.

BACKUP SYSTEM: Ensures that the unit continues to operate during an AC power

disruption (in order to preserve the battery life, the display is switched off). All clock,

date and alarm settings will be kept in the memory, however, the clock time may

require adjustment for exact accuracy. If no battery is installed, the display will blink to

indicate that you have to reset the time and alarm.

1. Slide the SETTING mode switch (19) to CLOCK position, press / (10) to

select the time mode between 12hours and 24hours, press DATE/SET (5) to confirm .

Then the hour digits will flash, press / (10) to adjust the value. The time

decrements or increments at a faster rate when you press and hold the buttons. Confirm

with DATE/SET (5). Repeat this procedure for the minute, year, sequence (D-M or M-

D) and value of day (“D”) and month (“M”)

1. ON/OFF button

2. LCD display

3. ALM.1 button

4. ALM.2 button

5. DATE/SET button

6. NAP button

7. SLEEP button

8. Speaker

9. Projector

10. SNOOZE/ / button

11. Projector ON/OFF switch

SETTING THE TIME

GB - 1 GB - 2

GB - 4GB - 3

INDOOR / OUTDOOR TEMPERATURE

GB - 5

M-180CR

User Manual

In/Out temperature projection clock radio

PLEASE READ THE INSTRUCTION CAREFULLY

BEFORE OPERATING THE UNIT

English

UNPACKING YOUR UNIT

When you unpack your new clock radio, make sure that you have removed all the

accessories and information papers:

- Projection clock radio

- AC/DC adaptor

- External temperature remote sensor with transparent cover and wall bracket

- User manual

PRODUCT DESCRIPTION

Location of controls

12. ROTATE button (for projected

image)

13. ºC / ºF button

14. Battery backup compartment

15. 5V DC in jack

16. Volume control

17. Band selector: MW/FM

18. Tuning knob

19. SETTING mode selector: CLOCK/

ALM.1/ALM.2/LOCK

20. FM wire antenna

21. Indoor temperature sensor

LCD display

POWER SUPPLY

AC/DC adaptor

- The supplied AC/DC adaptor is suitable

for use on AC mains supplies of 230V~

50Hz and should only be connected to a

mains supply with these parameters.

Caution:

- The included AC/DC adaptor is for use

with this unit only. Do not use it with other

equipments.

- When the unit is not going to be used for

long time, disconnect the AC/DC adaptor

from the AC outlet.

- Be sure to use it near the wall outlet. If a

malfunction occurs, disconnect the plug

from the wall outlet at once.

- When the AC/DC adaptor is plugged in, the apparatus is not completely disconnected

from the main power source, even when the unit is turned off.

- The AC/DC adaptor shall not be exposed to dripping or splashing and that no objects

filled with liquids, such as vases, shall be placed on apparatus.

- To be completely disconnect the power input, the AC/DC adaptor of apparatus shall

disconnected from the mains.” as the disconnect devices is the AC/DC adaptor of

apparatus.

- The AC/DC adaptor of apparatus should not be obstructed OR should be easily accessed

during intended use.”

Note: Pressing DATE/SET button (5) again, enters a new setting cycle.

Once the unit is plugged in, it will enter the time setting mode. ”24Hr” blinks on display.

2. Slide the SETTING mode switch (19) to LOCK position. The calendar is viewed for

3 seconds and display resumes to clock mode.

Pressing DATE/SET (5) displays the calendar for 3 seconds

Indoor temperatare

Once the unit is connected, the indoor temperature is displayed (2).

Celsius (ºC) and Fahrenheit (ºF).degrees selection

The button (13) switches the unit for both indoor and outdoor temperature

between Celsius (ºC) and Fahrenheit (ºF) degrees.

Outdoor temperature

1. Remote sensor set-up

- Remove the wall bracket.

- Unlock two latches at the bottom to release the transparent cover.

- Slide down the battery door at the back.

- Insert 2 batteries, type R03/UM4/AAA (not provided). Follow the polarity indicated in

the battery compartment

- An alkaline type battery is recommended. For optimum performance this battery should

be replaced every 6 months.

2. Remote sensor synchronization

- To enter synchronization mode, press and hold (10) for 3 seconds on the main

unit, “ ” flashes on the display (2) for 2 minutes.

- Press RESET button of the remote sensor with pointed object (such as ball-point

pen). The LED blinks

- A few seconds later the temperature will appear on the display of the main unit.

- To exit synchronization mode, press button (10), “ ” is not displayed.

Note:

* To synchronize remote sensor and main unit on a different channel, press CH button

and repeat synchronization operations.

* Once connected, the unit enters in synchronization mode with the remote sensor for

2 minutes. “ ” flashes on the display.

3. Replace battery door and transparent cover, lock the 2 latches at the bottom. Install

the remote sensor within a range of 50 meters from main unit in open area.

4. “ ”on the outdoor temperature area of the display, indicates that the remote

sensor batteries are low. Replace them with new batteries.

After battery replacement, or after main unit reset, or if the sensor is under the influence

of electrical fast transient or/and electrostatic phenomenon, reset the remote sensor

with the RESET button.

Note:

* If the unit fails to received the outdoor temperature for ,10 minutes it will display

“ - - . - “ .

* Displayed temperature and remote sensor operating range: -10.0°C to +60.0°C (+14.

0°F to +140.0°F)

未命名－１ 2009-9-8, 16:171

Produkt Specifikationer

Mærke:	Muse
Kategori:	Clockradio
Model:	M-180CRW
Vekselstrømsindgangsspænding:	230 V
Vekselstrømsindgangsfrekvens:	50 Hz
Bredde:	74 mm
Dybde:	166 mm
Højde:	122 mm
Vægt:	350 g
Antal pr. pakke:	1 stk
Brugervejledning:	Ja
Produktfarve:	Hvid
Skærmtype:	LCD
Pakkevægt:	850 g
Pakkedybde:	192 mm
Pakkebredde:	85 mm
Pakkehøjde:	168 mm
Indbyggede højttaler(e):	Ja
Slumretimer:	Ja
Kalender:	Ja
Termometer:	Ja
Strømkilde:	Vekselstrøm
DC-in-stik:	Ja
AC-adapter inkluderet:	Ja
Baggrundsfarve:	Blå
Antal indbyggede højttalere:	1
Vækkeur:	Ja
Baggrundslys:	Ja
Lydalarm:	Ja
Alarmfunktion:	Ja
Snooze funktion:	Ja
Projektion, funktion:	Tid