Muse M-198 BT Manual

Muse Bilradio M-198 BT

Læs gratis den danske manual til Muse M-198 BT (3 sider) i kategorien Bilradio. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Muse M-198 BT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Reset

1. Do not attempt to modify the unit, modifying the unit may cause an accident.

2. Installation or servicing of the unit by persons without training and experience in

electronic equipment and automotive accessories may be dangerous and could

expose you to the risk of electric shock or other hazards.

3. Stop the vehicle before carrying out any operation that could interfere with your driving.

4. Keep the volume at a level which you could hear sounds from outside the vehicle.

5. Do not work in extremely high or low temperature. Be sure the temperature inside the

vehicle is between +60°C and -10°C before turning on your unit.

6. When replacing the fuse(s), the replacement must be of the same amperage as

shown on the fuse holder.

7. Do not block vents or radiator panels. Blocking them will cause heat to build up inside

and may result in re.

8. Using this unit without running the engine can result in battery drainage.

9. Use only in cars with a 12 volt negative ground.

10. After completing the installation or replacing the car battery, you need to RESET the

unit before using it. Press button on the front panel with pointed object (such as RESET

ball-point pen) to reset the unit to its initial settings.

M-198 BT

GB - 1

User Manual

CAR RADIO WITH BLUETOOTH & USB/SD

Please read the instruction carefully

before operating the unit.

PRECAUTIONS UNPACK YOUR UNIT CONNECTION

INSTALLATION

LOCATION OF CONTROLS

BASIC OPERATIONS

LISTENING TO THE RADIO

SOUND FEATURES

GB - 2 GB - 3

Do not connect the ignition wire (red) and the battery wire (yellow), it may cause

a short circuit, even result in re.

NOTE:

This unit does not have built-in mic, make sure the external microphone (supplied)

is connected when the unit is installed to the car.

GB - 4 GB - 5 GB - 6

When you unpack your new car radio, make sure that you have removed all the

accessories and information papers:

Main unit

User manual

Accessories:

GB - 7

English

1. button /MU

2. button

3. buttonCLK

4. buttonBAND / AP

5. LCD display

6. USB port

7. SD/MMC card slot

8. button

9. SEL / Volume knob

10. buttonMODE/PTY

11. buttonRESET

12. button1 /

13. button2 / INT

14. button3 / RPT

15. button4 / RDM

16. button5 / /-10

17. button6 / /+10

18. AUX jack

Caution!

- Make sure to connect the color coded leads according to the diagram. Incorrect

connections may cause the unit to malfunction or damage the vehicle’s electrical system.

- Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect

the left and right channel speaker cables each other or to the vehicle body.

- Make sure all the connections are completely correct before turning on your unit.

Turn on/off the unit

Press button to turn on the unit. Press and hold this button again to turn off the unit.

Note: When the unit is off, press any key to turn on the unit.

Selecting the mode

When the unit is on, press button repeatedly to select different source mode: MODE

TUNER USB CARD BT AUX.

Note: USB, CARD mode can not be selected if no such source was plugged in the unit.

Current time display

Press button to display the current time when unit is ON.CLK

Adjust time:

1. Press and hold to enter into setting mode.CLK

2. Rotate Volume knob anti-clockwise and clockwise to adjust the hour and minute value.

It will conrm your setting if no key is pressed for 5 seconds.

Reset the unit

Operating the unit for the rst time or after replacing the car battery, you must reset the

unit. To set the unit to initial status, press button located on the base with a pointed RESET

object. When some errors occur in display, you can also reset the unit, but it will erase

the clock setting and some memorized functions.

Selecting band

In tuner mode, repeatedly press button to select bands in following order: FM1 BAND

FM2 FM3 MW1 MW2.

Manual / automatic tuning

- Manual Search

Choose your radio station with or .

- Automatic search

Press and hold for few seconds or . The automatic search locates strong stations.

A station with a weak signal can be set manually by repeatedly pressing or .

NOTE: During the search operation, the sound level is automatically muted.

- By number button 1- 6

1. Tune to a station by or button.

2. Press and hold one of the number buttons for 2 seconds until LCD shows the 1- 6

corresponding number, which indicates that station is stored in the corresponding

number button.

3. Under radio mode, press Number buttons to listen to stored stations.1- 6

4. When you are listening to a station stored on a number button, press and hold another

number button for more than 2 seconds to store the station on this number button.

Note: The unit can be stored up to 6 stations for each band.

RDS (Radio Data System)

This unit has a built-in RDS decoder system that supports broadcast stations transmitting

RDS data. This system can automatically switch to the broadcast station with the best

reception as you move on long distances (AF switching). Also if a trafc announcement

(TA) or programme type (PTY) is broadcast from a RDS station, no matter what mode

you are in. this broadcast is received.

Press and hold knob, the unit will enter setting menu. Shortly press SEL/volume

SEL/volume SEL/volume knob to choose your desire item. Rotate knob to choose

corresponding setting desired.

- Alternative frequency (AF)

When the AF switching mode is selected, the radio scans the signal strength of alternative

frequencies. A new AF is stronger than the current station, it switches over to that frequency

for very short time, and the new frequency is displayed for 1-2 second. (When AF ashes

on LCD, it will search for the stronger RDS station.)

Segment off: AF switching mode off.

Segment on: AF switching mode on, and receive RDS information.

Segment ashing: AF switching mode on, but RDS information is not received yet.

- Trafc alarm (TA)

In the TA standby mode, when a trafc announcement broadcast starts, the trafc

announcement broadcast is received as top priority regardless of the function mode so

you can listen to it.

If you select TA mode off, while a trafc announcement broadcast is being received,

the trafc announcement broadcast reception is cancelled and the unit goes into the TA

standby mode.

- TA SEEK/TA ALM

TA SEEK mode: when newly tuned station does not receive TP information for 5 seconds,

the radio retunes to next station which has not the same station(PI) as the last station,

but has the TP information.

When TP information gets lost at the current station for retune time which is set by

RETUNE SHORT(60 seconds) or RETUNE LONG(90 seconds), the radio start to retune

to next same PI station. When same PI station is not received in 1 cyclic search, the radio

retunes to next station with TP information.

TA ALARM mode: when this mode is selected, any automatic retune mode is not activated.

Only double beep sound(ALARM) is out-put.

When newly tuned station does not have TP information for 5 seconds, beeps are sounded.

When TP information gets lost at the current station for retune time, the beep sound is

out-putted.

When newly tuned station has no RDS signal, PI SEEK may be suppressed.

- PI SOUND/ PI MUTE

PI SOUND mode: If a car is cruising between buildings, an oscillation phenomenon may

occur, due to different PI codes being received from the same AF.

PI MUTE mode: In above situation, the sound will be muted for less than 1 second.

- RETUNE L / RETUNE S

The initial time of automatic TA search or PI SEARCH mode is selected.

When PI information is not received during retune time , the radio start to retune to next

same PI station.

When same PI station is not received during 1 cyclic search, the radio goes to last station

and waits for 4-5 minutes until PI code is received.

RETUNE L mode: selected as 90 seconds.

RETUNE S mode: selected as 60 seconds.

Volume adjusting:

To increase or decrease the sound level, rotate knob clockwise or anti-clockwise.VOLUME

Muting the sound

When the unit is ON, press to mute the sound. Press again to restore.MU

Using SEL/volume knob to select sound feature

1) Repeatedly press knobSEL/volume

To select the desired mode for sound setting in the following order: “BASS” “TRE”

(Treble) “BAL” (Balance) “FAD” (Fader) “VOL”

After selecting the desired mode, you can adjust the level by rotating the volume knob.

2) In FM mode, press and hold knob, the unit will enter setting menu. Shortly SEL/volume

press knob will show below items:SEL/volume

TA(ON/OFF) AF(ON/OFF) TA(SEEK/ALARM) PI(SOUND/MUTE)

RETUNE(L/S) MASK(DPI/ALL) BEEP(ON/OFF) USER SET(FLAT/

CLASSIC/ROCK/POP) VOL(LAST/DEFA) EUROPE/AMERICA3 STEREO/

MONO LOUND(ON/OFF) DX/LOCAL CLK(ON/OFF) CLK(12/24)

After that, rotate knob to choose corresponding setting desired.SEL/volume

Preset equalizer (EQ)

When you are listening to pop music, classic music or rock music, use the equalizer to

adjust the sound quality. Rotate knob to select different equalizer mode in following volume

order: FLAT CLASSIC ROCK POP EQ off.

Beep Tone

Choosing corresponding status can turn on or turn off beep.

4 SPEAKER SYSTEM

Rear Left

speaker

Front Left

speaker

Front Right

speaker

Rear Right

speaker

(Green/Black)

(Green)

(White/ Black)

(White)

(Gray/ Black)

(Gray)

(Violet/ Black)

(Violet) B1

Ground wire (Black)

Ignition wire (Red)

Power Antenna Amplifier Turn on (Blue)

+12V Constant Power Supply (Yellow)

Antenna socket

RCA out front (white = L / Red = R)

BT ANTENNA

MIC IN

To boost up the capability of anti-jamming,

please make sure fix tightly the metal support

strap into the metal joint that connect to the

chassis of the car.

DASHBOARD

Bend the tabs on the metal mounting

sleeve against the DASHBOARD with

a screwdriver

METAL MOUNTING SLEEVE

METAL SUPPORT STARP

To remove the unit out of the metal mounting sleeve,

insert the two supplied KEYS into the left and right side

slots of the chassis at the same time. Then pull the chassis

out of the metal mounting sleeve as shown in the right

illustration.

PLASTIC TRIM RING

FRONT PANEL

UNIT CHASSIS

AR-3633 IB MUSE 001 REV0 GB.indd 1 2014/7/7 11:20:12

Produkt Specifikationer

Mærke:	Muse
Kategori:	Bilradio
Model:	M-198 BT
Produktfarve:	Sort
Indbygget skærm:	Ja
Skærmtype:	LCD
Kompatible hukommelseskort:	MMC,SD,SDHC
Bluetooth:	Ja
USB-port:	Ja
FM radio:	Ja
Equalizer:	Ja
Understøttede lydformater:	MP3
Volumenkontrol:	Dreje
Linie-udgang (RCA):	1
Lyd-output kanaler:	4.0 kanaler
Udgangseffekt:	100 W
Understøttede disktyper:	Ingen
Indbygget kortlæser:	Ja
Effektkrav:	11 - 16 V DC
USB version:	2.0
DIN størrelse:	1 DIN
Antal USB-porte:	1
AUX-indgang:	Ja
Understøttede radiobånd:	FM,MW
RDS Tuner inkluderet:	Ja
MP3-afspilning:	Ja
Direkte USB-afspilning:	Ja
CD-R-afspilning:	Ingen
CD-RW-afspilning:	Ingen
Belysningsfarve:	Blå
Antal forudindstillede stationer:	30
Vigtig belysningsfarve:	Blå
Mikrofon inkluderet:	Ja
Understøttelse af ID3 Tags:	Ja
Udgangseffekt (DIN):	4 x 25W
Subwoofer-udgang:	Ja
Forudindstillet udgående port:	Ja