MuxLab 500759-TX-DANTE Manual

MuxLab Audio/video konverter 500759-TX-DANTE

Læs gratis den danske manual til MuxLab 500759-TX-DANTE (2 sider) i kategorien Audio/video konverter. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 3 anmeldelser. Har du et spørgsmål om MuxLab 500759-TX-DANTE, eller vil du spørge andre brugere om produktet?

Side 1/2
© MuxLab Inc. 94-000903-A SE-000903-A
2321Rue Cohen, Montreal, Quebec, Canada. H4R 2N7
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E
-
mail:
info@muxl
ab.com
URL:
www
.muxlab.co
m
Specifications
Environment HDMI 2.0b
Devices
Blu
-
Ray
, projectors, monitors, TV, PC, laptops, servers supporting HDMI.
Transmission
Transparent to the user
.
Bandwidth
300
MHz
Signals
HDMI
2.0b, HDR10, and HDCP 2.2
Connectors
Note: C
ables not include
d.
One (1) HDMI receptacle.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
Two (2) 3.5mm jacks for IR emitter (on TX)/sensor (on RX).
Two (2) 3.5mm jacks for audio insert (on TX)/audio extract (on RX)
One (1) DB9 for the RS232.
Four (4) DI
P Swi
tches for device ID addressing.
Maximum Distance
Based on a maximum length
of 6.6ft (2m) of HDMI cable
per end.
Cat5e/6: 330ft (100m) up to 4K @ 30Hz (4:4:4) and 4K @ 60Hz (4:2:0)
Note: When installed in an electrically noisy environment, an STP cable must be
used. Also, cross-connection reduces the effective distance depending on the
grade of twisted cable used.
Latency
Typical o
ne (1) Frame
(16ms), maximum 2 frames (33ms)
.
Compression Proprietary Compression.
Bandwidth
Up to
500
Mbps
.
Network Requirement
100
0
BaseT
with Jumbo Frame
.
IR Frequency 38 to 56 KHz (IR Emitter and IR Sensor sold separately).
RJ45 Pin Configuration
Reverse Polarity Sensitive.
Use EIA/TIA 568A or 586B
straight-through wiring.
RJ45 Link
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Cable
One (1) Cat 5e/6 or better twisted pair cables required
.
Power Supply This device supports PoE (PD), an external power supply is not included. It is
intended to be powered via a PoE (PSE) Ethernet Switch. If required, an optional
power supply (500993) may be purchased separately.
PoE
IEEE 802.3af
Power Consumption
Transmitter:
6
Watt
Receiver:
6
Watt
Temperature Operating: to 40°C Storage: -2 to 85°C
Humidity: Up to 95% non
-
condensing
Dimensions
4.40
x
5.0
8
x
1.00
” (
112
mm
x
12
9
mm
x
25
mm)
Weight
1.
5
lb
s
(0.
68
kg)
Compliance
Regulatory: FCC, CE, RoHS
Flammability: 94V0
Warranty
3
years
Order Information 500759-TX HDMI 4K over IP PoE Transmitter
500759
-
RX
HDMI
4K over IP PoE
Receiver
Accessories
(These items are sold
separately)
500920 16-Port Rackmount Transceiver Chassis
500917 Wall Mount Transceiver Bracket Kit
500990 IR Emitter, and 500991 IR Sensor
500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU Blade
HDMI/Dante over IP PoE Extender
500759 TX Dante
Quick Installation Guide
Overview
MuxLab’s HDMI/Dante over IP PoE Transmitter, UHD-4K (model 500759-TX-Dante) delivers
HDMI at up to 4K@30Hz with Dante audio to create an independently distributed AV network.
Hundreds of displays and various video wall configurations are supported, depending on network
bandwidth. Audio can be independently distributed to hundreds of Dante supported audio devices.
Each Transmitter can be connected via Cat5e/6 cable up to 330ft (100m) from an Ethernet Switch.
These units support HDR10 at up to 4K @ 30Hz (4:2:2).
The Transmitter supports PoE (PD) and may be powered by a PoE (PSE) Ethernet Switch. The IR
Emitter and IR Sensor, if required, may be purchased separately for IR based remote control
applications.
For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet switch must
have Gigabit ports, DHCP server capability, and support IGMP and Jumbo Frames. MuxLab
recommends using the Cisco SG350 series Managed Switches or the SG550X series stackable
version.
Applications
Applications including any audio Dante digital systems in professional and commercial
applications over long distances.
Installation
1. Identify the connectors on the Transmitter as indicated on the product labels, see the above front
and rear product views for further details.
2. Verify that the distance between the HDMI Transmitter is within MuxLab specifications (see
Specifications table for more details).
3. To install the Transmitter:
3a. Connect the Transmitter to the HDMI video source with an HDMI compliant cable.
3b. If the application is point-to-point, then connect one (1) length of Cat 5e/6 (or higher)
grade UTP cable to the RJ45 LINK connector on the Transmitter. If transmitting over
the network, use an Ethernet Switch between Transmitter and Receiver
4. Configuring Dante equipment
4a Use the free Dante Audinate Controller software found on the Audinate website
(https://www.audinate.com/products/software) to manage the connectivity between the
500759 TX Dante and other Dante audio equipment. Both point-to-point and point-to-
multipoint connections are supported.


Produkt Specifikationer

Mærke: MuxLab
Kategori: Audio/video konverter
Model: 500759-TX-DANTE

Har du brug for hjælp?

Hvis du har brug for hjælp til MuxLab 500759-TX-DANTE stil et spørgsmål nedenfor, og andre brugere vil svare dig




Audio/video konverter MuxLab Manualer

MuxLab

MuxLab 500756 Manual

5 November 2025
MuxLab

MuxLab 500755 Manual

4 November 2025
MuxLab

MuxLab 500033 Manual

4 November 2025
MuxLab

MuxLab 500734-SM80 Manual

4 November 2025
MuxLab

MuxLab 500777-TX Manual

4 November 2025
MuxLab

MuxLab 500774-RX-MM Manual

29 September 2025
MuxLab

MuxLab 500762-RX-V2 Manual

29 September 2025
MuxLab

MuxLab 500730 Manual

28 September 2025
MuxLab

MuxLab 500462 Manual

28 September 2025

Audio/video konverter Manualer

Nyeste Audio/video konverter Manualer