Navico NSS evo2 Manual
Læs nedenfor 📖 manual på dansk for Navico NSS evo2 (100 sider) i kategorien Marine. Denne guide var nyttig for 27 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/100
ENGLISH
NSS evo2
Operator Manual
simrad-yachting.com
The Home page
The Home page is accessed from any operation by a short press on the Home key.
Key Description
1 Applications
Tap a button to display the application as a full page panel.
Press and hold a button to display pre-configured split page options for the
application.
2 Tools
Tap a button to access dialogs used for carrying out a task, or for browsing stored
information.
3 Close button
Tap to exit the Home page and return to the previous active page.
4 Favorites
Tap a button to display the panel combination.
Press and hold a favorite button to enter edit mode for the Favorites panel.
5 Mand Over Board (MOB) button
Tap to save a Man Over Board (MOB) marker at the current vessel position.
10 Introduction | NSS evo2 Operator Manual
Basic operation
Turning the unit on and off
Enter a short description of your concept here (optional). You turn the unit on and off by pressing and holding the Power key.
If the key is released before the shut-down is completed, the power off process is cancelled.
You can also turn the unit off from the System controls dialog, activated by a short press on
the Power key.
ÚNote: The System Controls dialog will not display the power off option when the unit is
configured as slave. Refer details in the NSS evo2 Installation manual.
First time startup
The first time the unit is started and after a master reset the system will run through an
automatic start-up sequence, including language setup and automatic data source selection.
You can select to interrupt this sequence and later configure the system yourself.
Standby mode
In Standby mode the sonar is set to standby, and the backlight for screen and keys are turned
off to save power. The system will continue to run in the background.
You select Standby mode from the System Controls dialog.
Switch from Standby mode to normal operation by a short press on the Power key.
Display illumination
Enter a short description of your concept here (optional).The display backlighting can be adjusted at any time from the System control dialog.
A night mode which optimizes the color palette for low light conditions, is included.
ÚNote: Details on the chart may be less visible when the Night mode is selected!
Locking the touch screen
Enter a short description of your concept here (optional).
You can temporarily lock the touch screen to prevent accidental operation of the system.
This feature is also useful when cleaning the screen while the unit is turned on.
When the touch lock is active you can only operate the units from the keys.
The touch screen operation is locked from the System control dialog.
You remove the lock function by a short press on the Power key.
2
14 Basic operation | NSS evo2 Operator Manual
Adjusting panel size
Enter a short description of your task here (optional).You can change the panel size for an active split page. The panel size can be adjusted for
both favorite pages and for predefined split pages.
1. Activate the System control dialog by pressing the Power key or by dragging your finger
from the top of the screen
2. Select the adjust splits option in the dialog
3. Drag the adjustment icon to resize the panel
4. Confirm your changes by tapping on of the panels or by pressing the rotary knob
The changes are saved to the the active favorite or split page.
Adding new favorite pages
Enter a short description of your task here (optional).
1. Tap the New icon in the favorite panel on the Home page to open the page editor dialog
2. Drag and drop page icons to set up a new page
3. Save the page layout
The display will return to the Home page, and the new page will be included in list of favorite
pages.
Edit favorite pages
Enter a short description of your task here (optional).
1. Tap the edit icon or press and hold a favorite icon to enter edit mode
- Tap the cancel icon to remove a page
- Tap the tools icon to display the page editor dialog
2. Add or remove panels in the page editor dialog, then save your changes
3. Press the X key to leave the favorite edit mode
Basic operation | NSS evo2 Operator Manual 17
Charts
The chart function displays your vessel’s position relative to land and other chart objects. On
the chart panel you can plan and navigate routes, place waypoints and display AIS targets.
You can overlay a radar image, a StructureScan image or weather information.
The NSS evo2 is delivered with different cartography depending on region. All units will
support Navionics Platinum Plus, TurboView and C-Map (by Jeppesen) via micro-SD card or
via the Ethernet network.
Charts can be shared over the Ethernet network, so only one chart card per boat is required.
The Chart panel
Key Description Comment
1 Waypoint *
2 Vessel with extension line Extension line is optional
3 Route *
4 North indicator
5 Grid *
6 Range rings *
7 Track *
8 Chart range scale
9 Range rings interval Only displayed when Range
rings are turned on
* Optional chart items
ÚNote: You turn the optional images on/off individually. For more information, see "Chart settings"
on page 28.
3
20 Charts | NSS evo2 Operator Manual
North up
Displays the chart with the north direction upward. Corresponds to the usual orientation of
nautical charts.
Heading up
Displays the chart with the vessel’s heading directly up on the chart image. Heading
information is received from a compass. If heading is not available, then the COG from the
GPS will be used.
Course up
Rotates the chart in the direction of the next waypoint when navigating a route or navigating
to a waypoint. If not navigating the heading up orientation will be used until navigation is
started.
Look ahead
Centres the chart slightly forward of your vessel so that you can maximize your view ahead.
Displaying information about chart items
When you tap a chart item, a waypoint, a route or a target, basic information for the selected
item will be displayed. By tapping a chart item's pop-up, all available information for that
item will be shown.
ÚNote: Popup information has to be enabled in chart settings to see basic item information.
Available information for a selected chart item can also be displayed by using the menu.
Using the cursor on the chart panel
The cursor is by default not shown on the chart panel.
When you tap the screen, the cursor will become visible and the cursor position window will
be activated. When the cursor is active, the chart will not pan or rotate to follow the vessel.
Press the X key or tap the Clear cursor menu option to remove the cursor and cursor
window from the panel. This will also center the chart to vessel position.
Tap the Restore cursor menu option to display the cursor in its previous location. The Clear
cursor/Restore cursor are useful features for toggling between the vessel's current location
and the cursor position.
GoTo cursor
Enter a short description of your concept here (optional).
You start navigating to a selected position on the image by tapping the screen, then using
the go to cursor option in the menu.
22 Charts | NSS evo2 Operator Manual
Rock filter level
Hides rock identification on the chart beneath a given depth.
This helps you to declutter charts in areas where there are many rocks located at depths well
below your vessel draught.
Navionics view options
Chart shading
Shading adds terrain information to the chart.
Dynamic tide and current icons
Shows tides and currents with a gauge and an arrow instead of the diamond icons used for
static tides and current information.
The tide and current data available in Navionics charts are related to a specific date and time.
The NSS evo2 animates the arrows and/or gauges to show the tides and currents evolution
over time.
Dynamic tide information Dynamic current information
The following icons and symbology are used:
Icons Description
Current speed.
The arrow length depend on the rate, and the symbol is rotated
according to flow direction. Flow rate is shown inside the arrow symbol.
Red symbol used when current speed is increasing,- blue symbol when
current speed is decreasing.
Tide height.
The gauge have 8 labels and is set according to absolute max/min value
of the evaluated day.
Red arrow used when tide is rising,- blue arrow when tide is falling.
ÚNote: All numeric values are shown in the relevant system units (unit of measurement) set by
user.
Easy View
Magnifying feature increasing the size of chart items and text.
ÚNote: There is no indication on the chart showing that this feature is active.
26 Charts | NSS evo2 Operator Manual
Chart settings
Settings and display options made in the Chart settings page are common for all chart
panels.
3D boat selection
Determines which icon to use on 3D charts.
Range Rings
The range rings can be used to present the distance from your vessel to other chart objects.
The range scale is set automatically by the system to suit the chart scale.
Vessels’ extension lines
Sets the length of the extension lines for your vessel and for other vessels shown as AIS
targets.
• A: Heading
• B: Course Over Ground (COG)
The length of the extension lines are either
set as a fixed distance, or to indicate the
distance the vessel will move in the selected
time period. If no options are ticked on for
This vessel then no extension lines will be
shown for your vessel.
Own vessel heading is based on information
from the active heading sensor and COG
from active GPS sensor.
For other vessels COG data is included in the
message received from the AIS system.
Synchronize 2D/3D chart
Links the position shown on one chart with the position shown on the other chart when a
2D and a 3D chart are shown side by side.
Pop-up information
Selects whether basic information for chart items shall be displayed when you tap the item.
Grid lines
Turns on/off viewing of longitude and latitude grid lines on the chart.
Waypoints, Routes, Tracks
Turns on/off displaying of these items on chart panels.
28 Charts | NSS evo2 Operator Manual
Routes
A route consists of a series of routepoints entered in the order that you want to navigate
them.
When you tap a route on the chart panel it will turn green, and the route name will be
displayed.
Creating a new route on the chart panel
1. Tap the screen to activate the cursor
2. Select the new route option from the menu
3. Tap the chart panel to position the first waypoint
4. Continue tapping the chart panel until all routepoints are positioned
5. Save the route by pressing the save option in the menu.
Creating routes using existing waypoints
Enter a short description of your topic here (optional).
You can create a new route by combining existing waypoint from the Routes dialog. The
dialog is activated by using the Routes tool on the Home page.
Converting a track to a route
Enter a short description of your topic here (optional).
You can convert a track to a route from the
Edit Track dialog. The dialog is activated by
activating the track, then tapping the track's
pop-up, pressing the rotary knob or
selecting the info options from the menu.
The Edit Track dialog can also be access by
using the Tracks tool on the Home page.
30 Waypoints, routes and tracks | NSS evo2 Operator Manual
Starting a route from the chart panel
Tap a route on the panel, and then select the route navigation option from the menu.
You can tap a routepoint to start navigating from a selected position.
Start navigating a route from the Route dialog
You can start navigating from the Route dialog, activated by:
• Selecting the Route tool from the Home page
• Selecting the route details from the menu
Cancel navigation
When you are navigating a route the menu will include an option for cancelling the route.
Navigating with the autopilot
When you start navigation on a system with autopilot functionality, you will be prompted to
set the autopilot to navigation mode.
If you choose not to engage the autopilot, the autopilot can later on still be set to navigation
mode from the pilot menu.
For more information about autopilot functionality, refer to "Autopilot" on page 37.
Navigation settings
Navigating | NSS evo2 Operator Manual 35
Produkt Specifikationer
| Mærke: | Navico |
| Kategori: | Marine |
| Model: | NSS evo2 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Navico NSS evo2 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Marine Navico Manualer
5 Juli 2024
Marine Manualer
- Marine Kenwood
- Marine Lowrance
- Marine Garmin
- Marine Humminbird
- Marine Silva
- Marine Navman
- Marine Icom
- Marine Raymarine
- Marine Simrad
- Marine Furuno
- Marine Navionics
- Marine Rockford Fosgate
- Marine President
- Marine Fusion
- Marine Eagle
- Marine Lofrans
- Marine AdvanSea
- Marine Alphatron
- Marine Polmar
- Marine Klarfit
- Marine BandG
- Marine Dickinson Marine
- Marine Efoy
- Marine Nordwest-funk
- Marine Echotec
- Marine Interphase
- Marine Easy
- Marine Fastnet
- Marine KVH
- Marine Standard Horizon
- Marine SEAFARER
- Marine IVT
- Marine Nasa
- Marine WEST SYSTEM
- Marine Katadyn
- Marine Sailtron
- Marine Lorenz
- Marine Raytheon
- Marine Geonav
- Marine Digital Yacht
- Marine Plastimo
Nyeste Marine Manualer
15 Januar 2025
5 Oktober 2024
23 September 2024
21 September 2024
20 September 2024
18 September 2024
27 August 2024
27 August 2024
27 August 2024
26 August 2024