Nemco 55200AN-2 Manual

Nemco Skæremaskine 55200AN-2

Læs gratis den danske manual til Nemco 55200AN-2 (3 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Nemco 55200AN-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Easy Slicer ™ Vegetable Cutter

N55200AN Adjustable Cut N55200AN-1 3/16” Shredder

N55200AN-4 1/8” Fixed Cut N55200AN-2 5/16” Shredder

N55200AN-6 3/16” Fixed Cut

N55200AN-8 1/4” Fixed Cut

Operating and Maintenance Instructions

Important

1. To get the best operation and life from your machine, please read and comply with these instructions.

2. Clean machine thoroughly before and after each use using cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

Safety Instructions

1. Remember the blades are VERY SHARP; be careful when handling and operating the machine to keep hands away from the

blades.

2. Never operate the machine without the GUARD and COVER PLATE in proper position. Always push produce to the BLADES with the

PUSHER PLATE. Never push produce with the hand.

Preparation

1. Loosen screw in PUSH PLATE about 8 turns (or remove it completely)

2. Install PUSH PLATE in the grooves in the TROUGH AND LEG ASSEMBLY.

3. Place GUIDE under the head of the screw and tighten the screw.

4. If unit fails to operate properly when first used call NEMCO customer service at 1-800-782-6761

To Mount

1. Place the EASY SLICER on the work surface to establish a location that is convenient and comfortable for the operator. Draw an

outline of the MOUNTING BASE on the work surface.

2. Remove the MOUNTING BASE from the EASY SLICER and place within the outline drawn on the work surface. Draw circles where

the 4 holes are located and remove the MOUNTING BASE.

3. Drill ¼’ (or slightly larger) holes in work surface where holes in MOUNTING BASE were located – 4 holes.

4. Secure the MOUNTING BASE to the work surface with screws provided.

Note: The LEG can be repositioned by removing the 4 cap screws and installing with the LEG positioned as desired. This feature permits

mounting flexibility for convenience and for BASE that may already be installed foruse of the EASY SLICER™ with a MOUNTING

mounting other NEMCO machines.

To Operate

1. Slide the EASY SLICER™ into the MOUNTING BASE, with the extension containing the LOCKING SCREW going in last. Tighten the

LOCKING SCREW to secure the machine.

2. If using the ADJUSTABLE SLICING UNIT, check slice thickness setting and adjust if necessary (see TO ADJUST).

3. Pull PUSHER HANDLE and raise COVER PLATE and place produce into the TROUGH.

4. Close COVER PLATE and gently push on PUSHER HANDLE KNOB while turning the HANDLE on the ROTARY CUTTING UNIT in a

clockwise direction. Maintain uniform pressure on the PUSHER HANDLE.

To Adjust

1. The ADJUSTABLE SLICING UNIT is easily adjusted by holding the HANDLE stationary and by turning the ADJUSTING SCREW at the

end of the ADJUSTING SHAFT ASSEMBLY.

2. The thickness of the slice is indicated by the alignment of the pin in the slot and the lines on the recessed portion of the MAIN SHAFT.

These lines are 1/16” apart; so 2 lines = 2/16” or 1/8”, 3 lines = 3/16”, etc., up to ½”.

Operating Tips

1. For slice uniformity, turn the ROTARY SLICING UNITS slower as the slice width increases. This will help assure that the produce is

fully advanced to the ADJUSTING PLATE before the next BLADE begins to cut.

2. After placing produce in the TROUGH, turn the HANDLE about ¼ turn counter-clockwise before turning in the cutting direction. This

will permit a “running start” as the blade makes its first cut. It will be easier and will provide more uniform slices.

3. Do not apply heavy pressure on the PUSHER improve the slicing or shredding action.HANDLE. It is unnecessary and will not

4. Do not force produce that is too large into the TROUGH. It will be difficult to push into the CUTTING BLADE and will result in poor

uniformity of the cut.

5. Keep the BLADES sharp.

Produkt Specifikationer

Mærke:	Nemco
Kategori:	Skæremaskine
Model:	55200AN-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 55200AN-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Nemco Manualer

27 August 2025

27 August 2025

27 August 2025

27 August 2025

27 August 2025

27 August 2025

Nemco 55650-CS Manual

26 August 2025

Nemco 55650-1 Manual

26 August 2025

Nemco 55450-1 Manual

26 August 2025

Nemco 55300A-2 Manual

26 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Leifheit 3222 Manual

29 Oktober 2025

Alpha Tools FSG 920 Manual

12 Oktober 2025

Ritter Sinus 1 Manual

10 Oktober 2025

Ritter Sono² Manual

10 Oktober 2025

Ritter Markant 05 Manual

10 Oktober 2025

Vollrath 40900 Manual

30 September 2025

Vollrath 40901 Manual

30 September 2025

Fry Factory AFC-50 Manual

28 September 2025

Jaccard Fillet-O-Matic Manual

28 September 2025

Jaccard VA 2000 Manual

28 September 2025