Nemco 55500-2 Manual

Nemco Skæremaskine 55500-2

Læs gratis den danske manual til Nemco 55500-2 (2 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Nemco 55500-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Easy Chopper™

55500–1 1/4” Cut

55500-2 3/8” Cut

55500-3 1/2” Cut

55500-4 1” Cut

OPERATING AND MAINTENANCE INSTRUCTIONS

Important

1. To get the best operation and life from your machine, please read and comply with these instructions.

2. Clean machine thoroughly before and after each use using cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

Safety Instructions

Remember that the blades are VERY SHARP; be careful when handling and operating the machine to keep hands away from

the cutting edges.

Operation of Easy Chopper ™

1. Place the chopper on a good firm work surface.

2. Your Easy Chopper ™ produce chopper comes to you fully assembled.

3. Prepare the produce to be chopped (core, cut, slice, wedge to your specifications).

4. Lift HANDLE and place the produce on the blades.

5. Remove hand/fingers from the cutting area and with a strong, quick thrust, bring the PUSH BLOCK down to force the produce

through the BLADES. Lift and repeat.

6. Clean the machine after chopping is completed using cleaning instructions below.

Caution: Do not attempt to chop produce larger than the opening in the BLADE HOLDER.

Note: Since BLADE AND HOLDER ASSEMBLES for different sized cuts are interchangeable, you may have more than one set

available for use. BEFORE CHOPPING be sure that the PUSH BLOCK is the correct one to use for the cutting size desired. Gently

lower the PUSH BLOCK onto the BLADE AND HOLDER ASSEMBLY to see that the PUSH BLOCK GUIDE rests on the BUMPERS. If it

does not, something is wrong and must be corrected before chopping produce.

To cut 1/4”, 1/2” use 1/4” PUSH BLOCK

To cut 3/8” use 3/8” PUSH BLOCK

To cut 1” use 55610 PUSH BLOCK

To Clean

1. Lift the HANDLE and PUSH BLOCK GUIDE off the GUIDE RODS.

2. Remove BUMPERS and lift the BLADE AND HOLDER ASSEMBLY off the GUIDE RODS.

3. Thoroughly wash the PUSH BLOCK GUIDE, the PUSH BLOCK, the BLADE AND HOLDER ASSEMBLY and the FRAME.

4. The PUSH BLOCK can be removed from the PUSH BLOCK GUIDE by removing THUMBSCREWS for further cleaning.

5. The BLADE AND HOLDER ASSEMBLY may also be totally disassembled for further cleaning as follows:

a) Remove THUMBSCREWS and the BLADE HOLDER PLATE.

b) Gently tap the BLADES and the BLADE SPACERS from the BLADE HOLDER.

6. To Reassemble:

a) Place the BLADE HOLDER on a table top with the BLADE SPACER pockets upward.

b) Insert the 4 BLADE SPACERS with their slots toward the inner opening of the BLADE HOLDER.

c) Insert BLADES with sharp edge downward and slots upward.

d) Insert BLADES with sharp edge and slots downward.

e) Reposition the BLADE AND HOLDER ASSEMBLY and secure with THUMBSCREWS.

7. Reposition BLADE AND HOLDER assembly, the BUMPERS, the PUSH BLOCK, the PUSH BLOCK GUIDE and HANDLE on the

FRAME.

Chopping Tips

Cut produce before chopping and place a cut surface against the BLADES. Onions and tomatoes dice best if cut from top to bottom.

They may be cut in half, or if smaller dices are desired, they can be cut several times in this direction.

To Lubricate

When needed, lubricate the GUIDE RODS with Mineral Oil, Food Grade Grease, or rub them with Paraffin. DO NOT LUBRICATE

WITH COOKING OIL – IT GETS STICKY!

TO REPLACE BLADES OR BLADE SPACERS

If necessary, the BLADES and/or BLADE SPACERS can be replaced. To do this, follow Instruction 5 of TO CLEAN.

Produkt Specifikationer

Mærke:	Nemco
Kategori:	Skæremaskine
Model:	55500-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 55500-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Nemco Manualer

27 August 2025

27 August 2025

27 August 2025

27 August 2025

27 August 2025

27 August 2025

Nemco 55650-CS Manual

26 August 2025

Nemco 55650-1 Manual

26 August 2025

Nemco 55450-1 Manual

26 August 2025

Nemco 55300A-2 Manual

26 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Leifheit 3222 Manual

29 Oktober 2025

Alpha Tools FSG 920 Manual

12 Oktober 2025

Ritter Sinus 1 Manual

10 Oktober 2025

Ritter Sono² Manual

10 Oktober 2025

Ritter Markant 05 Manual

10 Oktober 2025

Vollrath 40900 Manual

30 September 2025

Vollrath 40901 Manual

30 September 2025

Fry Factory AFC-50 Manual

28 September 2025

Jaccard Fillet-O-Matic Manual

28 September 2025

Jaccard VA 2000 Manual

28 September 2025