Nemco 55350A Manual


Læs gratis den danske manual til Nemco 55350A (1 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Nemco 55350A, eller vil du spørge andre brugere om produktet?

Side 1/1
EASY CHEESE BLOCKER
N55350A
OPERATING AND MAINTENANCE INSTRUCTIONS
IMPORTANT
1. To get the best operation and life from your machine, please read and comply with these instructions.
2. Clean machine thoroughly before and after each use using cleaning instructions below.
3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.
OPERATION
1. This EASY CHEESE BLOCKER will cut up to 40 pound blocks of cheesedown to size with speed and ease.
3. Remove wrapping from the cheese.
4. Lift CUTTING BOW and place the cheese on the BASE so the intended cut is over the slot. Gently, but firmly, pull the CUTTING
BOW downward to make the cut.
NOTE: The notches on the top of the FRONT PLATE and the raised dots on the BASE indicate ½ increments from the line of cut. They
will aid in aligning the cheese block and in positioning the Cheese Blocker for uniform slices.
5. Remove the portion cut-off, raise the CUTTING BOW and position the cheese for the next cut.
6. If unit fails to work properly when first operated call NEMCO customer service at 1-800-782-6761.
CLEANING
NOTE: Proper maintenance plays an important part in the life span and functioning of the unit
1. The EASY CHEESE BLOCKER is dishwasher safe or can be placed in a sink for conventional washing methods.
2. The FRONT PLATE can be readily removed for cleaning by removing the THUMB SCREWS.
3. The machine can be totally disassembled with small hand tools.
TO REPLACE CUTTING WIRE
1. Remove THREAD CAPS and loosen WING NUTS.
2. Place the new CUTTING WIRE loops on the EYEBOLT and L-SCREW.
3. Tighten the WING NUT on the L-SCREWS until the L-SCREW is secure against the CUTTING BOW. The L must be in the vertical
position.
4. Replace the THREAD CAP.
5. Tighten the WING NUT on the EYEBOLT to bring the eye secure against the CUTTING BOW. Replace THREAD CAP.
NOTE: Avoid twisting the wire when tightening the WING NUTS.
NEMCO FOOD EQUIPMENT 301 Meuse Argonne, Hicksville, OH 43526
Phone: (419) 542 7751 Fax: ( ) 419 542-6690 Toll Free: 1-800-782-6761 46019
www.nemcofoodequip.com 10/30/03


Produkt Specifikationer

Mærke: Nemco
Kategori: Skæremaskine
Model: 55350A

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 55350A stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skæremaskine Nemco Manualer

Nemco

Nemco 55350A Manual

14 November 2025
Nemco

Nemco 55450-8 Manual

14 November 2025
Nemco

Nemco 55050AN Manual

12 November 2025
Nemco

Nemco 55450-3 Manual

12 November 2025
Nemco

Nemco 55450-2 Manual

11 November 2025
Nemco

Nemco 55500-3 Manual

27 August 2025
Nemco

Nemco 56500-1 Manual

27 August 2025
Nemco

Nemco 55150B Manual

27 August 2025
Nemco

Nemco 56610-1 Manual

27 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

GARDE

GARDE 181DM14SC Manual

13 November 2025
GARDE

GARDE 181DM14 Manual

12 November 2025
GARDE

GARDE 181DM14WM Manual

12 November 2025
GARDE

GARDE 181DM12 Manual

12 November 2025
GARDE

GARDE 181DM12WM Manual

11 November 2025
Leifheit

Leifheit 3222 Manual

29 Oktober 2025
Alpha Tools

Alpha Tools FSG 920 Manual

12 Oktober 2025
Ritter

Ritter Sinus 1 Manual

10 Oktober 2025
Ritter

Ritter Sono² Manual

10 Oktober 2025