Norlake AdvantEDGE NLTF23-S Manual

Norlake Fryser AdvantEDGE NLTF23-S

Læs gratis den danske manual til Norlake AdvantEDGE NLTF23-S (7 sider) i kategorien Fryser. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Norlake AdvantEDGE NLTF23-S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

1 07/ Rev B 20 171226

TOP MOUNT

REFRIGERATORS FREEZERS ,

Installation, Operation and Maintenance Instructions

INSPECTION

When the equipment is received, all items should be carefully checked against the Bill of

Lading to ensure all crates and cartons have been received. Do not sign the freight bill

clear until the freight has been properly inspected for damage. All units should be

inspected for damage including concealed damage by uncrating immediately. If any

damage is found, it should be reported to the carrier at once, noted on the Bill of Lading

and a claim should be led with the carrier. This equipment has been inspected and tested

in the manufacturing facility and has been crated in accordance with transportation rules

and guidelines. The manufacturer is not responsible for freight loss or damages.

INSTALLATION

CAUTION: This unit uses a ammable refrigerant. Use care when handling and

operating to avoid damaging the refrigerant tubing or increasing the risk of a leak.

The unit has been secured to the shipping base with four bolts. Remove these bolts and

separate the unit from the shipping base. Locate the casters or legs found inside the unit.

Attach the casters or legs to the unit base by screwing them into the threaded ttings that

were used to secure the shipping base. Use the wrench provided to tighten the casters to

the unit. The casters with the brakes should be installed on the front of the unit. For proper

drainage of condensate, the unit should be level when placed in its permanent location.

Leveling shims are included in the accessories package in the cabinet. Loosen the casters

and insert shims between caster and bottom of the unit. Re-tighten the caster.

The exterior of the cabinet and doors have been protected by a plastic covering. Peel this

protective covering before installation. After removing the covering, clean the interior and

exterior surfaces of the unit with soap and water and a rinse with clean water. Do not use

chlorinated cleaners on the surfaces as they can cause corrosion.

If the door(s) have come out of alignment during shipping, they will need to be adjusted.

This can be accomplished by opening the door(s) and loosening the screws that hold both

the top and bottom hinges to the cabinet. After adjusting the door so it is aligned correct,

tighten the screws to securely hold the hinges and door(s) in place.

The shelves and shelf clips are packaged inside the unit. Install the shelf clips on the

pilasters inside the unit and set the shelves on the clips. The shelves are adjustable in

12.7mm( inch)increments. ½

3 07/ Rev B 20 171226

MAINTENANCE

All service should be performed by factory authorized personnel. All component

parts will be replaced with like components to minimize the risk of possible ignition

due to incorrect parts or improper service.

Cleaning

Beginning with the initial installation, the interior surfaces of the cabinet should be

periodically cleaned with a solution of warm water and baking soda. This solution will

remove any odors from spillage that has occurred. The exterior of the cabinet should also be

cleaned frequently with a commercial stainless steel cleaner, glass cleaner or mild soap

s ution. Do not use chlorinated cleaners on the stainless steel surfaces. ol

Note: do not use stainless steel cleaner or other solvent-based chemicals on plastic

parts (door handle or facade parts) as they could cause failure. Use mild soap and

warm water on plastic parts.

The door gaskets should be cleaned in place with a mild soap solution to extend their life.

The shelving can be cleaned in a sink with a mild soap solution and a soft bristled brush.

Condenser Coil

Disconnect the unit from power prior to cleaning the condenser coil. Periodic cleaning of the

condenser coil will aid the heat transfer of the refrigeration system and increase its

eciency. Cleaning is recommended a minimum of every months. 6

To do this, lift the top grill from the cabinet and secure it. The condenser coil is located

behind the grill. Use a soft bristled brush to remove any dirt particles that are on the ns of

the condenser coil. Use a vacuum cleaner or compressed air to remove the loosened

particles. Lower the top grill and x it with screw, then reconnect the device to the power

source. Failure to clean the condenser coil can lead to performance loss and compressor

failure.

Produkt Specifikationer

Mærke:	Norlake
Kategori:	Fryser
Model:	AdvantEDGE NLTF23-S

Har du brug for hjælp?

Hvis du har brug for hjælp til Norlake AdvantEDGE NLTF23-S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fryser Norlake Manualer

Norlake AdvantEDGE NLTF23-S Manual

14 August 2024

Norlake AdvantEDGE NLUF48 Manual

11 August 2024

Norlake AdvantEDGE NLUF27A Manual

10 August 2024

Norlake AdvantEDGE NLTF49-S Manual

6 August 2024

Fryser Manualer

Nyeste Fryser Manualer

Heinner HDF-1800SS Manual

4 Juli 2025

Haier HAF5TWA 011 Manual

4 Juli 2025

Elektra Bregenz FSN 9950 Manual

4 Juli 2025

Electrolux KRF6EW1L Manual

4 Juli 2025

Electrolux EUT6NE28K1 Manual

4 Juli 2025

Electrolux EUN7ND18C Manual

4 Juli 2025

Electrolux EUE9NEW1 Manual

4 Juli 2025

Electrolux PU6NE28U1 Manual

4 Juli 2025

Moulinex Easy Fry Dual Flex EZ9228 Manual

4 Juli 2025

Electrolux EUE3NEW1 Manual

4 Juli 2025