Norlake AdvantEDGE NLUF48 Manual

Norlake Fryser AdvantEDGE NLUF48

Læs gratis den danske manual til Norlake AdvantEDGE NLUF48 (4 sider) i kategorien Fryser. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Norlake AdvantEDGE NLUF48, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

0 5/15 Rev. C 143493

UNDERCOUNTER REFRIGERATORS AND FREEZERS

Installation, Operation and Maintenance

Instructions

INSPECTION

When the equipment is received, all items should be carefully checked against the B ill

of Lading to insure all crates and cartons have been received. Do not sign the freight

bill clear until the freight has been properly inspected for damage. All units should be

inspected for damage including concealed damage by uncrating immediately. If any

damage is found, it should be reported to the carrier at once, noted on the Bill of Lading

and a claim should be filed with the carrier. This equipment has been inspected and

tested in the manufacturing facility and has been crated in accordance with

transportation rules and guidelines. The manufacturer t responsible for freight loss is no

or damages.

INSTALLATION

The exterior of the cabinet and doors have been protected by a plastic covering. Peel

this protective covering before installation. After removing the covering, clean the

interior and exterior surfaces of the unit with soap and water and a rinse with clean

water. Do not use chlorin ted cleanersa on the surfaces as they can cause corrosion.

If the door(s) have come out of alignment during shipping they will need to be adjusted.

This can be accomplished by opening the door(s) and loosening the screws that hold

both the top and bottom hinges to the cabinet. After adjusting the door so it is aligned

correct, tighten the screws to securely hold the hinges and door(s) in place.

The shelves and self clips are packaged inside the unit. Install the shelf clips on the

pilasters inside the unit and set the shelves on the clips. The shelves are adjustable in

½” increments. can support One (1) shelf up to 132 lbs ( kg). 60

The refrigeration system located in the rear of the unit requires free air access for

proper operation. Allow a minimum of seven inches between the back of the cabinet

and the wall. Do not locate the unit next to heat generating equipment or in direct

sunlight.

Confirm that the proposed electrical outlet has the correct voltage, frequency and

current carrying capacity for the requirements of the unit. This information is noted on

the data plate on the inside left wall of the unit. The unit should be isolated on a circuit.

Do not use an extension cord to get power to the unit. Improper electrical installations

will void the compressor warranty. To prevent shock and fire, be sure the unit is

properly grounded.

The temperature controller is located at the top, right corner inside the cabinet. Adjust

the temperature to fit your needs.

0 5/15 Rev. C 143493

Install casters per the following diagram.

Note: The casters with brakes should be installed to the front of the cabinet.

MAINTENANCE

General Cleaning

Beginning with the initial installation, the interior surfaces of the cabinet should be

periodically cleaned with a solution of warm water and baking soda. This solution will

remove any odors from spillage that has occurred. The exterior of the cabinet should

also be cleaned frequently with a commercial stainless steel cleaner, glass cleaner or

mild soap solution. Do not use chlorinated cleaners on the stainless steel surfaces.

Note: do not use stainless steel cleaners or other solvent based chemicals on the -

plastic parts (door handle or trim strips) as they can cause failure. Use mild soap and

warm water on plastic parts.

The door gaskets should be cleaned in place with a mild soap solution to extend their

life.

The shelving can be cleaned in a sink with a mild soap solution and a soft bristled

brush.

Condenser Coil Cleaning

Prior to cleaning the condenser coil disconnect the unit from power. Periodic cleaning

of the condenser coil will aid the heat transfer of the refrigeration system and increase

its efficiency. To accomplish this, remove the rear grill from the cabinet. The condenser

coil is located behind the grill. Use a soft bristled brush to remove any dirt particles that

are on the fins of the condenser coil. Use a vacuum cleaner or compressed air to

remove the loosened particles. Replace the grill and reconnect the unit to power.

Failure to clean the condenser coil can lead to performance loss and compressor

failure.

Stocking

When loading the cabinet with contents, do not block the fans in the back. Blocking the

air flow may decrease performance.

Produkt Specifikationer

Mærke:	Norlake
Kategori:	Fryser
Model:	AdvantEDGE NLUF48

Har du brug for hjælp?

Hvis du har brug for hjælp til Norlake AdvantEDGE NLUF48 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fryser Norlake Manualer

Norlake AdvantEDGE NLTF23-S Manual

14 August 2024

Norlake AdvantEDGE NLUF48 Manual

11 August 2024

Norlake AdvantEDGE NLUF27A Manual

10 August 2024

Norlake AdvantEDGE NLTF49-S Manual

6 August 2024

Fryser Manualer

Nyeste Fryser Manualer

Liebherr FNc 467i Manual

13 September 2025

Liebherr FNsddi 1624 Plus Manual

13 September 2025

Liebherr BFPSvh 6501 Manual

13 September 2025

Liebherr FNd 505i Prime Manual

13 September 2025

Liebherr SFFvh 4001 Manual

13 September 2025

Liebherr EFL 3005 Manual

13 September 2025

Liebherr CBNsfc 5223 Plus Manual

13 September 2025

Liebherr FNa 6625 Plus Manual

13 September 2025

Liebherr FNc 527i Manual

13 September 2025

Liebherr FFFCvg 4001 Manual

13 September 2025