NUVO Ballerina 60/181 Manual

NUVO lampe Ballerina 60/181

Læs gratis den danske manual til NUVO Ballerina 60/181 (1 sider) i kategorien lampe. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om NUVO Ballerina 60/181, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling, which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this

fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to misplace

any of the screws or parts, which are needed to install this

fixture.

STEP 2: Thread the nipple (K) into pipe (L) and the coupling

(M).

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Thread nut (D) onto nipple (E) so that five threads are

exposed above nut (D). Insert lock washer (C) and

thread nipple (E) onto mounting bar (A), then secure

with the nut (D), secure mounting bar (A) to outlet box

with outlet box screws (B).

STEP 2: Thread screw collar (H) onto the nipple (E). Slide

screw collar ring (G) and canopy (F) over chain (I).

Using two pairs of pliers, open one link of chain (I) and

connect it to the fixture loop (J).

BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.

STEP 3: Lace wires up through chain (I) and pass wires through

holes in screw collar (H). We recommend lacing wire

up through every other link of chain (I).

GROUNDING INSTRUCTIONS

STEP 1: The green grounding screw is to be inserted into the

hole with two raised dimples provided on the mounting

bar. Wrap the ground wire from the fixture (if supplied)

and the ground wire from the outlet box (bare metal) or

green insulated wire around the green grounding screw

on the mounting bar. If uninstalled wire is on the

mounting bar, connect the ground wire from the fixture

(if supplied) and the outlet box to it using a small wire

connector (not supplied).

NOTE: Underwriters Laboratories does not require all fixtures to

have ground wires. These fixtures still meet all U. L.

specifications.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and

connect the wires according to the directions below:

GROUP A: Connect to Black

House Wire

GROUP B: Connect to White

House Wire

BLACK WHITE

*PARALLEL WIRE (round &

smooth)

*PARALLEL WIRE (square &

ridged)

WHITE OR GREY WITH

TRACER

WHITE OR GREY WITHOUT

TRACER

BROWN GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is round

in shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your fixture wire(s) from group A and place

evenly against the black wire from the outlet box. Do

NOT twist wires together before using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the

connector clockwise until you feel firmness.

STEP 5: Try gently to pull the connector off the wires. If you can

pull the connector off, carefully re-do steps 3 and 4 as

above, and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire

from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box, then secure canopy (F) with screw collar

ring (G).

STEP 2: Thread nut (O) onto the nipple (P) then thread the

nipple (P) into the coupling (N) and secure the nipple

(P) with nut (O).

STEP 3: Raise the cap (Q) onto the nipple (P) then secure with

finial (R).

STEP 4: Slide the glass shade (T) over the socket (S) and

secure with the retaining ring (U).

STEP 5: Install lamps. (Please do not exceed the maximum

capacity recommended on the socket.)

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ITEM NO:60-181 60-182 60-183 60-184 60-185 60-186

60-187 60-188 60-1251 60-1252

NUV

A Satco Product

LIGHTING

Produkt Specifikationer

Mærke:	NUVO
Kategori:	lampe
Model:	Ballerina 60/181

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO Ballerina 60/181 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

lampe NUVO Manualer

NUVO Arabel 60/6967 Manual

4 April 2025

NUVO Gotham 60/191 Manual

4 April 2025

NUVO Cordello 60/7884 Manual

4 April 2025

NUVO Clarksville 60/8061 Manual

4 April 2025

NUVO Gotham 60/190 Manual

4 April 2025

NUVO Odeon 60/2855 Manual

1 April 2025

NUVO Beacon 60/6827 Manual

1 April 2025

NUVO Clarksville 60/8066 Manual

1 April 2025

NUVO Harlow 60/4630 Manual

12 September 2024

NUVO Laguna 60/5925 Manual

12 September 2024

lampe Manualer

Nyeste lampe Manualer

Integral LED ILSTRGBWB028E Manual

4 April 2025

Trust Shyne 25483 Manual

3 April 2025

Trust Vybz GXT 904 Manual

3 April 2025

Schonbek Priscilla BC7106N-48PBZ Manual

2 April 2025

Bresser BR-7RGB Mini Tube Manual

2 April 2025

Sonneman Ray 2036 Manual

2 April 2025

Maxim Charlton 11375BKAB Manual

2 April 2025

Schneider OVA48313 Manual

1 April 2025

Schneider OVA44112 Manual

1 April 2025

Schneider OVA47013 Manual

1 April 2025