Oliveri DZ122NTH Manual

Oliveri Vask DZ122NTH

Læs gratis den danske manual til Oliveri DZ122NTH (2 sider) i kategorien Vask. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Oliveri DZ122NTH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS

CAUTION

Leave protective tape on the sink when inverting over a benchtop and tracing its shape. The stainless

steel will scratch if the sink slides across a hard surface.

Topmount sinks may also be known as “drop in” or “inset” sinks.

Topmount models with prex PR, SN, NP, MO, DZ, PE, LL, UF, PL, MR, EL & TI.

These sinks will t into standard 600mm bench tops.

Templates are available for download from www.oliverisinks.com

Download PDF template from www.oliverisinks.com. If the template is not available, the cutout shape may be created by

carefully inverting the sink onto the counter/benchtop and tracing around the perimeter.Cut the hole 10mm inside the traced line.

Many Oliveri sinks have waste outlets positioned to the rear of the bowls. Ensure the sink is correctly positioned when tting.

Unequal bowl depth:

Sinks that combine different sized bowls may also have unequal bowl depth. Waste plumbing will need to

accommodate this variance. All sinks have a height adaptor included with the sink where needed.

Solitaire models (LR)

LR510 & LR515 may be top mounted, each using a circular cutout 466mm in diameter. LR515 comes with a 32mm diameter

taphole pre-cut in the tap landing. Mark the location of this taphole when trial tting the sink. Then, drillout the counter/benchtop

in the appropriate location so that the mixer tap can be solidly installed through both the sink and the counter/benchtop.

LR510 may also be under mounted in a solid-surface counter/benchtop using a circular cut out 454mm in diameter

after edges are smoothed. Refer Oliveri undermount instructions for recommended installation methods.

MATERIALS FOR FITTING THE UNDERMOUNT SINK:

• Oliveri sink (with correct tap holes as ordered) - includes mounting clips,

sealing gasket, basket wastes and other accessories (depending on

model).

• These Installation Instructions

• Level to check counter/benchtop & sink is installed level

• Phillips head screwdriver (#2 to tighten mounting clips)

• Flat head screwdriver (large - to tighten basket wastes)

• Suitable sealant (neutral-cure silicone sealant or equivalent)

• Masking material to protect counter/benchtop and sink from excess

sealant

• Additional Mounting Hardware if tting into thinner material. The

clamps included with the sink require a minimum counter/benchtop

thickness of 25mm / 1”.

INSTALLER - PLEASE READ & FOLLOW THESE

INSTALLATION INSTRUCTIONS

Please retain for consumer as care instructions are included

IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT AT TIME OF CUTTING

Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in

relation to goods manufactured by it or their use and installation, is given in good faith and is believed by

Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,

assistance or service is provided by Tasman Sinkware without responsibility or liability.

FOR “TOP MOUNT” OR “DROP IN” SINKS

CHECK MODEL

The model number on the sink

packaging must match the model

of sink the customer ordered.

Do not install if incorrect.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

CHECK THE CONDITION

Inspect the sink for any visible

defects. Do not install the sink if

defects are found. Contact your

sink retailer / point of purchase.

AVOID SCRATCHES

Stainless steel can be scratched

if proper care is not taken during

installation.

Download cutout

template files

(PDF, DWG & DXF)

from our website.

AUSTRALIA

Head Ofce &

Manufacturing Plant

Tasman Sinkware Pty Ltd

Regency Park SA

Phone: +61 8 8348 6444

Fax: +61 8 8348 6495

Email: sinkware@oliverisinks.com.au

oliveri.com.au

TF 08f May 2017

Produkt Specifikationer

Mærke:	Oliveri
Kategori:	Vask
Model:	DZ122NTH

Har du brug for hjælp?

Hvis du har brug for hjælp til Oliveri DZ122NTH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vask Oliveri Manualer

Oliveri FL122 Manual

3 Marts 2025

Oliveri ST-BL1530U Manual

1 September 2024

Oliveri ST-BL1584U Manual

1 September 2024

Oliveri TI70 Manual

1 September 2024

Oliveri LL117 Manual

31 August 2024

Oliveri PR1190U Manual

31 August 2024

Oliveri DZ172 Manual

31 August 2024

Oliveri NP6101TH Manual

31 August 2024

Oliveri PR1181 Manual

31 August 2024

Oliveri SN1050U Manual

31 August 2024

Vask Manualer

Nyeste Vask Manualer

Caple BLAGDON Manual

8 April 2025

Kernau KGS G 4560 1B1D Manual

8 April 2025

BLANCO NAYA 8 S Manual

7 April 2025

Kohler Gilford K-12700 Manual

30 Marts 2025

Sani-Lav ESB2-607L Manual

3 Marts 2025

Schock Primus N200 AP 07 Manual

26 Januar 2025

BLANCO ANDANO 340-U Manual

1 Januar 2025

Hendi 970522 Manual

30 December 2025

Blaupunkt Tesino STG5600CEA Manual

30 December 2025

Deante ZQE N10B Manual

28 December 2024