Oliveri DZ172 Manual

Oliveri Vask DZ172

Læs gratis den danske manual til Oliveri DZ172 (4 sider) i kategorien Vask. Denne vejledning er vurderet som hjælpsom af 68 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 34.5 anmeldelser. Har du et spørgsmål om Oliveri DZ172, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLER - PLEASE READ & FOLLOW

THESE INSTALLATION INSTRUCTIONS

Please retain for consumer as care instructions are included

EQUIPMENT REQUIRED for installing your Oliveri top mount sink:

MATERIALS FOR CUTTING COUNTER/BENCHTOP:

• Template for your particular model sink and mounting method (may be inside or printed

on carton depending on model). If not available, the sink itself may be used.

• Marker such as a pencil or similar for tracing the template onto the counter/benchtop

• Tape measure

• Drill with 12mm / ½” diameter bit or larger (wood counter/benchtop)

• Cutting Device (such as a jigsaw) with suitable blade for counter/benchtop material

• Suitable protection such as gloves and goggles to be used while drilling or cutting

MATERIALS FOR FITTING THE TOP MOUNT SINK:

• Oliveri sink (with correct tap holes as ordered) - includes mounting clips, sealing gasket,

basket wastes and other accessories (depending on model).

• These Installation Instructions

• Level to check counter/benchtop & sink is installed level

• Phillips head screwdriver (#2 to tighten mounting clips)

• Flat head screwdriver (large - to tighten basket wastes)

• Suitable sealant (neutral-cure silicone sealant or equivalent)

• Masking material to protect counter/benchtop and sink from excess sealant

• Additional Mounting Hardware if fitting into thinner material. The clamps included

with the sink require a minimum counter/benchtop thickness of 25mm / 1”.

CHECK MODEL & TAP HOLES

The model number on the sink

packaging must match the model

of sink the customer ordered.

Check the number and position of

tap holes is correct.

Do not install if incorrect.

CHECK THE CONDITION

Inspect the sink for any visible

defects. Do not install the sink if

defects are found. Contact your

sink retailer / point of purchase.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

AVOID SCRATCHES

Polished stainless steel can be

scratched if proper care is not

taken during installation.

Topmount sinks may also be known as “drop in” or “inset” sinks.

Sink models with prefix MO, PE, UF, DU, LR, EF, NP, MR, SI & RR.

These sinks will fit into standard 600mm bench tops.

Templates supplied are to assist in achieving the correct shape hole for top mounting the sink.

Careful use of the template is required to achieve the correct cutout shape. If the template is not available, the cut out shape may

be created by carefully inverting the sink onto the counter/benchtop and tracing around the perimeter. Cut the hole 10mm inside the

traced line.

Many Oliveri sinks have waste outlets positioned to the rear of the bowls. Ensure the sink is correctly positioned when fitting.

Unequal bowl depth:

Sinks that combine different sized bowls may also have unequal bowl depth. Waste plumbing will need to accommodate

this variance. MO, PE, NP, SI & RR sinks have a height adaptor included with the sink where needed.

Models UF03D & UF04D have a 60mm height difference in waste connections for the main and smaller bowl. Waste plumbing will

need to accommodate this variance.

Models UF05D & UF06D have a 35mm height difference in waste connections for the main and smaller bowl. Waste plumbing will

need to accommodate this variance.

EF models have a 35mm height difference in waste connections for the main and smaller bowl. Waste plumbing will need to

accommodate this variance.

Solitaire models (LR) - Cut out templates are not supplied with these sinks.

LR510 & LR515 may be top mounted, each using a circular cut out 466mm in diameter. LR515 comes with a 32mm diameter tap

hole pre-cut in the tap landing. Mark the location of this tap hole when trial fitting the sink. Then, drill out the counter/benchtop in the

appropriate location so that the mixer tap can be solidly installed through both the sink and the counter/benchtop.

For other topmount LR models that do not have a template, the cut out shape may be created by carefully inverting the sink onto

the counter/benchtop and tracing around the perimeter. Cut the hole 10mm inside the traced line.

LR510 may also be under mounted in a solid-surface counter/benchtop using a circular cut out 454mm in diameter after

edges are smoothed. Refer Oliveri undermount instructions for recommended installation methods.

MANHATTAN & DALLAS (MH or DA)

THESE SINKS WILL NOT FIT IN A STANDARD 600MM COUNTER/BENCH TOP.

Measure carefully to ensure sufficient room exists (including allowance for a splashback if required). The cutout shape may

be created by carefully inverting the sink onto the counter/benchtop and tracing around the perimeter. Cut the hole 10mm inside the

traced line.

FOR “TOP MOUNT’ OR “DROP IN” SINKS

NORTH AMERIC

Sales Office

Tasman Sinkware North America

Corona CA

Email: northamerica@oliverisinks.com

UNITED KINGDOM DISTRIBUTOR

A.C. Toon Ltd

Phone: 01246 223900

Email: sales@actoon.co.uk

AUSTRALI

Head Office &

Manufacturing Plant

Tasman Sinkware Pty Ltd

Regency Park SA

Phone: +61 8 8348 6444

Fax: +61 8 8348 6495

Email: sinkware@tasbuildpro.com.au

ASIA PACIFIC DISTRIBUTORS

New Zealand - Dux Industries

Ltd

Phone: 0800 367 389

Singapore - Sim Siang Choon

Phone: 6266 6632

Hong Kong - Deacon & Co Ltd

Phone: 2369 6111

Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in

relation to goods manufactured by it or their use and installation, is given in good faith and is believed by

Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,

assistance or service is provided by Tasman Sinkware without responsibility or liability.

SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS

CAUTION

Leave protective tape on the sink when inverting over a benchtop and tracing its shape.

The polished stainless steel will scratch if the sink slides across a hard surface.

AU Top Mount Installation Instructions

TF 08d.doc

Tasman Sinkware

is a division of

Fletcher Building

Produkt Specifikationer

Mærke:	Oliveri
Kategori:	Vask
Model:	DZ172

Har du brug for hjælp?

Hvis du har brug for hjælp til Oliveri DZ172 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vask Oliveri Manualer

Oliveri FL122 Manual

3 Marts 2025

Oliveri ST-BL1530U Manual

1 September 2024

Oliveri ST-BL1584U Manual

1 September 2024

Oliveri TI70 Manual

1 September 2024

Oliveri LL117 Manual

31 August 2024

Oliveri PR1190U Manual

31 August 2024

Oliveri DZ172 Manual

31 August 2024

Oliveri NP6101TH Manual

31 August 2024

Oliveri PR1181 Manual

31 August 2024

Oliveri SN1050U Manual

31 August 2024

Vask Manualer

Nyeste Vask Manualer

Caple BLAGDON Manual

8 April 2025

Kernau KGS G 4560 1B1D Manual

8 April 2025

BLANCO NAYA 8 S Manual

7 April 2025

Kohler Gilford K-12700 Manual

30 Marts 2025

Sani-Lav ESB2-607L Manual

3 Marts 2025

Schock Primus N200 AP 07 Manual

26 Januar 2025

BLANCO ANDANO 340-U Manual

1 Januar 2025

Hendi 970522 Manual

30 December 2025

Blaupunkt Tesino STG5600CEA Manual

30 December 2025

Deante ZQE N10B Manual

28 December 2024