Oliveri Essente SS31625 Manual

Oliveri Kran Essente SS31625

Læs gratis den danske manual til Oliveri Essente SS31625 (2 sider) i kategorien Kran. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Oliveri Essente SS31625, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation Instructions
Technical Data
THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN
ACCORDANCE WITH LOCAL REGULATIONS.
This Oliveri tap is manufactured to standard AS/NZS 3718.
Before attempting any work involving mains water supply lines, ensure the water supply is
shut off.
Stop valves must installing your mixer to (preferably with filters) be used when Oliveri allow
isolation (not supplied with mixer). Failure to do so where required will void warranty.
This mixer tap is already pre-assembled and tested. Do not disassemble, as this may void
This mixer tap must be installed in accordance with these instructions.
Oliveri Solutions Pty Ltd ABN 12 007 551 8
86
51 Naweena Rd, Regency Park SA 5010 P 08 8348 6444 E sales@oliveri.com.au
Where water pressure exceeds 500kPa, a pressure reducing device is required to be installed.
Note that water pressure overnight can reach 150% of the daytime pressure.
Note:
Installation of aerators containing flow regulators.
Upon re-installation, the aerator should be tightened with an aerator key to prevent
removal by hand.
Note:
Ceramic Cartridges - Warranty claims will not be honoured where the ceramic
cartridge has malfunctioned due to the presence in the water supply of;
• Copper tube pieces, sand, dirt or stones
• Thread tape
• Other objects not normally present in potable water supplies.
Do not remove the cartridge from the body as it has been pressure tested and
tightened to a specific torque.
MAX OPERATING PRESSURE: ...................................................... 5 bar (500kPa)
RECOMMENDED OPERATION PRESSURE: ................................... 1.5-5 bar (150-500kPa)
MAX HOT WATER TEMPERATURE: ............................................. 65°C
RECOMMENDED HOT WATER TEMPERATURE: ............................ 50°C
TF 182 - SS 25 Installation Instructionse 316
Essente
Stainless Steel Goose Neck Pull Out Mixer
SS 25 / SS 25-AU / SS 25-BL / SS 25-GM316 316 316 316 / SS31625-CU
CARE & MAINTENANCE
Unscrew and clean the spout aerator periodically - especially if you notice a drop in water
pressure. The finish on your Oliveri mixer tap will resist stains and dirt build up.
Clean with a soft cloth and warm soapy water as necessary - rinse and dry after cleaning.
Avoid using abrasive or acid based cleaning products.-
WARRANTY FOR DOMESTIC USE
This mixer tap is warranted to be free from manufacturing defects for a period of
1 Years: Cartridge: 1 years replacement parts, 1 year labour; Body including handle: 5 5
7 years replacement parts and labour; Finish: 5 years replacement parts, 1 year labour;
Seals, tails, aerators, pull-out hoses and spray heads: 1 year replacement parts and labour.
Where a genuine manufacturing defect arises within the warranty period Oliveri will, at its
election, repair the defect or replace the product subject to the terms contained in the full
warranty information available at https://oliveri.com.au/service-and-warranty.
This warranty does not cover against normal wear and will be voided if the
product is misused or not installed in accordance with these instructions. Note:
Fitting spout-attached devices, including water filters, to this mixer will void warranty.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure.
SERVICE
If the problem represents a danger, or damage to property may occur,
immediately shut off the water supply. If the mixer tap requires servicing, please
contact your plumber (preferably the one who installed it). Most problems occur due to
contaminated supply lines or water pressure exceeding 500kPa. Unscrew and clean the
spout aerator periodically - especially if you notice a drop in water pressure.
If the plumber / installer is satisfied that the problem is not due to poor installation,
contact Oliveri’s nominated Warranty Service Agent for assistance on:
Ph: (08) 8348 6444 (choose the after sales service and warranty option)
Email: warranty@oliveri.com.au
For full warranty information visit: https://oliveri.com.au/service-and-warranty
If a warranty service call finds that the product does not have a genuine
manufacturing fault, our Warranty Service Agent reserves the right to pass on
any call-out fee to the householder.
This product complies with the Lead Free requirements of the National
Construction Code Volume 3.
Installation Instructions
A
C
D
E
F
G
J
I
H
B
Max 37
K
TF 182 - SS 25 Installation Instructionse 316
GENERAL NOTE
This product is to be installed by
a licensed plumber, installation
must comply with AS/NZS 3500
and local plumbing codes.
PRESSURES & TEMPERATURES
Max
imum Hydrostatic Pressure – 500kPa. (As per AS/NZS3500)
Note: AS/NZS 3500.1-2003 (Clause 3.3.4) states that
”Provision shall be made to ensure that the maximum static
pressure at any outlet, other than a fire service outlet, within a building does not exceed 500kPa.”
Note: Pressures above 500kPa can cause damage from water hammer, reduced life of appliances, taps
and fittings, and cause excessive noise in the system. Minimum Hydrostatic Pressure 100kPa. :
Note: This Product may not be suitable for use with low pressure/gravity feed water supplies or with
some continuous flow/instantaneous hot water systems. The maximum operating temperature for the
Mixer Tap is 65ºC. The recommended maximum delivery temperature is 50ºC.
Please ensure that the lines are flushed prior to installation as contaminates in the water can
damage the Ceramic Cartridge, flow regulator and also affect the performance of the Mixer.
Note: This mixer is designed to have the handle to the right hand side of the mixer, doing so will put
the cold inlet to the front of the mixer, the purpose is to assist with accidental scalding if a child pulls
the handle forward trying to turn on the mixer, installing the handle to the centre will put the cold on
the left hand side which is not recommended.
1. Remove product from packaging and check for damages, if the product is damaged do not install
and return to store of purchase.
2. The WELS compliant aerator has been pre-assembled into the mixer outlet. To comply with
WELS
the flow regulated aerator must remain in place.
3. Ensure product is complete as per exploded drawing.
4. A single 35mm hole is required in the mounting surface.
5. The maximum mounting surface thickness cannot exceed 37mm.
6. Fit O-ring (A) to bottom of mixer body.
7. Screw Mixer Tails (B) into the base of the mixer being careful not to damage the O-ring seals., Hand
tighten only.
8. Feed male end of Braided Hose (H) through top of mounting surface.
N.B. Hose Adaptor (J) and Washer (I) are lightly screwed to male end of Hose (H), this fitting will
need to be removed for ease of feeding hose through mounting surface.
9. Feed the Mixer Tails (B) through the mounting surface, each tail alternatively.
10. The mixer inlet ports are colour coded, red for hot and blue for cold.
11. Position mixer on the mounting surface ensuring the Sealing Washer (A) is positioned correctly.
12. Feed mixer tails, each alternatively through Stabiliser Plate (C).
13. Slide Rubber Washer (D) onto mixer thread followed by Metal Washer (E).
14.Using Fixing Nut (F), tighten mixer to mounting surface, lock fixing nut in place with Screws (G).
15.Screw Hose Adaptor (J) to male threaded end of Hose (H) ensuring Sealing Washer (I) is in place.
16.Screw Hose Adaptor (J) to Mixer Water Outlet port being careful to avoid damage to the
O-ring seals.
17.
18.
Connect Mixer tails (B) to mains water 1/2"stop cock. Tighten to 10Nm. Do NOT overtighten.
N.B. Ensure the Mixer Tails are not kinked, bent, stretched or twisted when assembling to
the mains water supply. The mixer tail connection between the mixer and the water
supply must hav
e a natural curve (minimum bend radius 30 mm). Ensure Mixer tails are
installed indoors, above-ground, and remain accessible - do not bury, submerge, nstall behind a i
wall, floor or ceiling. Do not not expose to abrasions, corrosive agents or the like. Test for leaks: If a
leak occurs, retighten slightly.
19.It is recommended that in-line filters be installed to ensure a cleaner flow of water to the mixer.
20.The Braided hose will have a natural curve under the mounting surface, on the hand piece side of
the curve fit the Return Weight (K) using the two screws provided. Fit the weight approximately
100mm up from the bottom of the curve, the position can be adjusted to suit but the weight must
remain on the hand piece side of the curve.
TO THE CONSUMER
1. The mixer is to only be cleaned with warm soapy water.
2. Under no circumstances should any abrasive, cream or acid based cleaning agents be used as
these types of cleaners will damage the tap finish, cartridge, seals and aerators.

Produkt Specifikationer

Mærke: Oliveri
Kategori: Kran
Model: Essente SS31625

Har du brug for hjælp?

Hvis du har brug for hjælp til Oliveri Essente SS31625 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Kran Oliveri Manualer

Oliveri

Oliveri KE2030 Manual

7 April 2025
Oliveri

Oliveri MT0039 Manual

7 April 2025
Oliveri

Oliveri Essente SS31670 Manual

25 December 2024
Oliveri

Oliveri Essente SS31625 Manual

25 December 2024
Oliveri

Oliveri Essente SS31620 Manual

25 December 2024
Oliveri

Oliveri VT0398 Manual

1 September 2024
Oliveri

Oliveri MT0269 Manual

1 September 2024
Oliveri

Oliveri BA118500CR Manual

31 August 2024
Oliveri

Oliveri BA118506MB Manual

31 August 2024
Oliveri

Oliveri PT2010B Manual

31 August 2024

Kran Manualer

Nyeste Kran Manualer

Rohl

Rohl Miscelo MI09D3GQMB Manual

7 April 2025
Sussex

Sussex VSM-04 Manual

7 April 2025
Shaws

Shaws AUSH-4341 Manual

7 April 2025
Shaws

Shaws AUSH-4751 Manual

7 April 2025
Sussex

Sussex CBM-54 Manual

7 April 2025
Sussex

Sussex VSMQ-60 Manual

7 April 2025
Shaws

Shaws AUSH-4756 Manual

7 April 2025
Shaws

Shaws AUSH-4861 Manual

7 April 2025
Shaws

Shaws AUSH-4866 Manual

7 April 2025
Sussex

Sussex VBM Manual

7 April 2025