Oliveri LL116 Manual

Oliveri Vask LL116

Læs gratis den danske manual til Oliveri LL116 (4 sider) i kategorien Vask. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Oliveri LL116, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CUTTING THE BENCHTOP GENERAL INFORMATION

GRANITE SINK INSTALLATION INSTRUCTIONS

Please retain for consumer as care instructions are included

SEALANT

Oliveri recommends using the sealant strip (supplied with the sink), to seal between the sink and the bench

top. However, if silicone is used, it MUST be a “Neutral Cure” product – the use of “Acetic Cure” silicone

can damage or discolour the sink and will void warranty.

WASTE DISPOSAL UNITS

Waste disposal units can be ﬁtted to Oliveri’s Granite Sinks. However, faulty or damaged waste disposal

units can cause vibration, which may lead to sink damage and will void warranty.

BASKET WASTE INSTALLATION

1 Fit the basket waste into the hole in the sink and then place the drain under the hole.

DO NOT USE SILICONE ADHESIVE.

2. Fasten the basket waste to the drain using a screw. Do not overtighten.

DRILLING THE TAP HOLE

Oliveri granite sinks with drainboards are provided with a pre-punched hole (picture A) placed on the front

and back of the sink in order to choose which side the bowls / drainer will sit. NOTE!

In order to avoid any possible damage to the sink, we strictly recommend to drill these pre-punched holes

using 35-37mm drill following the procedure shown in pictures B and C. We recommend using a diamond

coated drill to drill this hole.

Fig. A - Pre-punched tap holes Fig. B - Place the tool on the

pre-punched hole.

Fig. C - Drill the hole.

CHECK SPACE

Ensure there is adequate space for tapware (including a splashback if

speciﬁed). Check space for installation (underneath) and operation (above).

Particular care must be taken when a thick splash back is used (it may

interfere with tapware location and operation). Ensure the cabinet will not

foul the sink mounting ﬂange or basins.

TEMPLATE

Cut out templates for your Oliveri sink are available online at oliveri.com.au.

Use the product model number to ﬁnd the template. Some sink templates

apply to both left-hand and right-hand model sinks. Ensure template is

correct way around for your model.

MARK CUT OUT

Carefully mark out the template (or follow drawing instructions) making

allowance for any additional polishing back that is required after cutting.

Note: The template is the exact ﬁnished cut-out size required.

CUT & FINISH HOLE

Drill pilot holes to accept an appropriate cutting tool for the benchtop

material (wear suitable personal protection equipment). Cut inside the mark,

allowing sufﬁcient room for any polishing back.

Note: Accuracy is essential to ensure the bowl / basin and accessories

ﬁt correctly.

TRIAL FIT THE SINK

Carefully position the sink against benchtop to make sure it ﬁts the cut out

correctly. If the ﬁt is not correct, remove the sink and proceed with remedial

work. Perform another trial ﬁt after corrections have been made.

IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT AT TIME OF CUTTING

Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in relation to goods

manufactured by it or their use and installation, is given in good faith and is believed by Tasman Sinkware to be

appropriate and reliable. However, any advice, recommendation, information, assistance or service is provided by

Tasman Sinkware without responsibility or liability.

Download cut out ﬁles (PDF, DWG or DXF) from oliveri.com.au

CHECK MODEL

The model number on the sink

packaging must match the model

of sink the customer ordered.

Do not install if incorrect.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

CHECK THE CONDITION

Inspect the sink for any visible

defects. Do not install the sink if

defects are found. Contact your

sink retailer / point of purchase.

AVOID BREAKAGES

Granite sinks can be broken if

proper care is not taken during

installation.

Produkt Specifikationer

Mærke:	Oliveri
Kategori:	Vask
Model:	LL116

Har du brug for hjælp?

Hvis du har brug for hjælp til Oliveri LL116 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vask Oliveri Manualer

Oliveri FL122 Manual

3 Marts 2025

Oliveri ST-BL1530U Manual

1 September 2024

Oliveri ST-BL1584U Manual

1 September 2024

Oliveri TI70 Manual

1 September 2024

Oliveri LL117 Manual

31 August 2024

Oliveri PR1190U Manual

31 August 2024

Oliveri DZ172 Manual

31 August 2024

Oliveri NP6101TH Manual

31 August 2024

Oliveri PR1181 Manual

31 August 2024

Oliveri SN1050U Manual

31 August 2024

Vask Manualer

Nyeste Vask Manualer

Sani-Lav ESB2-607L Manual

3 Marts 2025

BLANCO ANDANO 340-U Manual

1 Januar 2025

Hendi 970522 Manual

30 December 2025

Blaupunkt Tesino STG5600CEA Manual

30 December 2025

Deante ZQE N10B Manual

28 December 2024

Deante ZZQZA2513 Manual

28 December 2024

Fulgor Milano P1B 7545 Q F-SF Manual

28 December 2024

Caple Zero 35 Manual

27 December 2024

Caple Zero 150R Manual

27 December 2024

Caple Zero 55 Manual

27 December 2024