Oliveri SS2575 Manual

Oliveri Kran SS2575

Læs gratis den danske manual til Oliveri SS2575 (4 sider) i kategorien Kran. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Oliveri SS2575, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Before attempting any work involving mains water supply lines, ensure the water supply is shut off.

Stop valves (preferably with ﬁlters) must be used when installing your Oliveri mixer to allow isolation. (not

supplied with mixer). Failure to do so where required will void warranty.

This mixer tap is already pre-assembled and tested. Do not disassemble, as this may void the warranty.

This mixer tap must be installed in accordance with these instructions.

Essente stainless steel square goose neck pull out mixer

SS2575

Where water pressure exceeds 500kPa, a pressure reducing device is required to be installed. Note that

water pressure overnight can reach 150% of the daytime pressure.

CARE & MAINTENANCE

Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure.

The polished chrome plate ﬁnish on your Oliveri mixer tap will resist stains and dirt build up.

Clean with a soft cloth and warm soapy water as necessary - rinse and dry after cleaning. Avoid using abrasive

or acid based cleaning products.

WARRANTY

This mixer tap is warranted to be free from manufacturing defects for a period of 10 Years: 5 years only (parts

& labour) plus an additional 5 years on the Cartridge (parts only), when used in a domestic situation.

This warranty does not cover against normal wear and will be voided if the product is misused or not

installed in accordance with these instructions. Note: Fitting spout-attached devices, including water ﬁlters,

to this mixer will void warranty.

In the event this product is rendered obsolete and a replacement product is required, Tasman Sinkware

reserves the right to supply a product of equal substitution at their discretion.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are

entitled to a replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

SERVICE

If the problem represents a danger, or damage to property may occur, immediately shut off the water supply.

If the mixer tap requires servicing, please contact your plumber (preferably the one who installed it).

Most problems occur due to contaminated supply lines or water pressure exceeding 500kPa.

If the Plumber is satisﬁed that the problem is not due to poor installation, contact T2 Services Pty Ltd for

assistance on:

Ph: (07) 5596 0738

Fax: (07) 5527 3353

Email: oliveri@t2services.com.au

If a warranty service call ﬁnds that the mixer tap is not at fault, T2 Services Pty Ltd reserves the right to pass

on any callout fee to the householder.

THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN

ACCORDANCE WITH LOCAL REGULATIONS

This Oliveri tap is manufactured to standard AS/NZS 3718.

Note: Installation of aerators containing ﬂow regulators.

Upon re-installation, the aerator should be tightened with an aerator key to prevent removal by hand.

Note: Ceramic Cartidges - Warranty claims will not be honoured where the ceramic cartridge has

malfunctioned due the the presence in the water supply of;

- Copper tube pieces, sand, dirt or stones

- Thread tape

- Other objects not normally present in potable water supplies.

- Do not remove the cartridge from the body as it has been pressure tested and tightened to a

speciﬁc torque.

Technical Data

Installation Instructions

TF 185b - SS2575 installation instructions.pdf

MAX OPERATING PRESSURE: ..............................................................5 bar (500kPa)

RECOMMENDED OPERATION PRESSURE: ..........................................1.5-5 bar (150-500kPa)

MAX HOT WATER TEMPERATURE: .....................................................65°C

RECOMMENDED HOT WATER TEMPERATURE: ..................................50°C

Produkt Specifikationer

Mærke:	Oliveri
Kategori:	Kran
Model:	SS2575

Har du brug for hjælp?

Hvis du har brug for hjælp til Oliveri SS2575 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kran Oliveri Manualer

Oliveri KE2030 Manual

7 April 2025

Oliveri MT0039 Manual

7 April 2025

Oliveri Essente SS31670 Manual

25 December 2024

Oliveri Essente SS31625 Manual

25 December 2024

Oliveri Essente SS31620 Manual

25 December 2024

Oliveri VT0398 Manual

1 September 2024

Oliveri MT0269 Manual

1 September 2024

Oliveri BA118500CR Manual

31 August 2024

Oliveri BA118506MB Manual

31 August 2024

Oliveri PT2010B Manual

31 August 2024

Kran Manualer

Nyeste Kran Manualer

Rohl Miscelo MI09D3GQMB Manual

7 April 2025

Sussex VSM-04 Manual

7 April 2025

Shaws AUSH-4341 Manual

7 April 2025

Shaws AUSH-4751 Manual

7 April 2025

Sussex CBM-54 Manual

7 April 2025

Sussex VSMQ-60 Manual

7 April 2025

Shaws AUSH-4756 Manual

7 April 2025

Shaws AUSH-4861 Manual

7 April 2025

Shaws AUSH-4866 Manual

7 April 2025

Sussex VBM Manual

7 April 2025