Olympia RS 50R Manual

Olympia Overvågningskamera RS 50R

Læs gratis den danske manual til Olympia RS 50R (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Olympia RS 50R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Read the assembly manual thoroughly and observe the information contained during installation.

Keep the assembly manual in a safe place for future reference.

Intended Use

The additional door lock increases property security when residents are inside the respective building

or room. Option: The installation of an outer cylinder enables the additional lock to be used on the door

even when the user is absent.

The additional door lock is intended for apartment and house entrance doors made of wood, steel, alu-

minium and composite materials. In the case of plastic and compound materials, a metallic prole must

be available at the assembly positions or a metallic plate underlaid on the other side.

Any other use is considered unintended use. Unauthorised modications or reconstructions not de-

scribed in the manual are not permitted and could cause the product to be damaged.

Safety Instructions

WARNING! Risk of suocation! Children can swallow small parts,

packaging and protective foils. Keep the product and packaging

out of reach of children!

IMPORTANT! Improper assembly can lead to property damage. Install the

additional door lock as described in this assembly manual. Only use the

assembly material supplied.

IMPORTANT! DO NOT use spray oils or anything similar. Clean the catch oc-

casionally with a dry cloth. The mechanism inside is already greased at the

factory. During assembly, pay attention that no wood chippings or similar

bits get into the lock cases when open.

Lock Unit

1Lock case

2Base plate

3Screw M5x10

4Screw 5x25

Door Lock RS 50

5Spacer base plate

6Screw 5x35

7Frame dowel

8Additional spacer plate

9Strike plate

10 Screw M5x15

11 Lock case

12 Screw M5x15

Assembly Manual

Door Lock RS 50R

13 Door guard

14 Retaining bolt

15 Retaining bolt spring

16 Safety cotter pin

Tools Required

■Cross-tip screwdriver

■3 mm wood drill

■10 mm masonry drill

■Marker, scriber

■Possibly a tape measure and

spirit level

Lock UnitDoor Lock RS 50R

Door Lock RS 50

Additional Door Lock RS 50 / Additional Door Lock RS 50R

Option (when using an

outer cylinder)

■32 - 35 mm hole cutter

■Pliers to shorten the catch

Disposal

Help protect the environment and

dispose of the product and packaging

materials according to the applicable

local regulations.

Further Information

Further information on this product is available at

http://productip.com/?f=84f9b

http://productip.com/?f=84f9d

Or scan this QR code.

When using an outer cylinder (C1/C2):

Measure the thickness of the door leaf and shorten the catch using a pair of pliers at one of the break-

ing points provided so that, when assembled, maximally 7 mm remains in the base plate. Guide the

covering escutcheon over the outer cylinder (C1) and rst slide the unit together with the catch through

the outside of the door. Then screw in the two screws (C2) supplied from the inside of the door.

5 Slide the lock case (1) on the base plate (2) and x it in place with the two screws (3) at the side.

6 The door lock unit must then be assembled on the door frame. Use the spacer base plate (5) to mark

the 6 drill holes. Ensure you maintain the correct clearance from locks already installed. Then drill

the holes using a 3 mm drill bit to a depth of approx. 10 mm and x the spacer base plate to the

frame using the 6 respective screws (6).

Use the frame dowel (7) for xation in the wall. Drill the hole for the dowel at an angle through the spac-

er base plate of the lock case using a 10 mm drill. Insert the dowel and screw in the screw rmly.

7 Fit the additional spacer plates (8) on the spacer base plate as necessary and x the strike plate (9)

on it using the two screws (10).

8 Finally, x the lock case (11) using the two screws (12) and complete a test locking operation.

Scope of Delivery

Check the package supplied is complete:

■ Additional door lock

■Assembly material

General Assembly Information

Determine the thickness of the door. Normally, an apartment or house entrance door is 40to 70 mm

thick. To use the optional outer cylinder, the door must be at least 30mm thick. The door leaf on which

the lock is to be installed as well as the frames must close properly and there must be no large gap.

Prior to assembly, check whether the door is hinged on the right or left.

The additional door lock is preassembled for doors hinged on the left. If you want to assemble the

additional door lock on a door hinged on the right, complete the following steps before beginning with

the assembly work:

Lock unit: Release the base plate (2) from the lock case (1) by loosening the 2 screws (3) at the side.

Remove the latch from inside of the lock case by loosening the two retaining screws, turn it 180° on

its longitudinal axis and install it in the lock case (1) again. Replace the base plate (2) and screw it tight.

Check the locking function.

RS 50R ONLY: Release the lock case (11). Remove the door guard (13) with retaining bolt (14) by remov-

ing the cotter pin (16) and install it in hole opposite. Replace the lock case (11) and screw it tight.

Plan the height of the additional door lock so that all users can reach the knob without any problem.

Otherwise, we recommend an installation height of 130 cm.

Installation

1 First of all, hold the door lock unit and door lock unit at the planned assembly positions on the door.

Both parts should be level and be at a height that the latch in the lock case can engage smoothly in

the opening in the lock unit. If you notice a dierence in the height, compensate for it by inserting

the additional spacer plates (8) supplied under the strike plate (9). Then set the lock case to one side.

2 Separate the Base plate (2) from the lock case (1) by removing the two screws (3) at the side.

3 Position the drilling aid supplied (according to the side of the hinge) and mark the four drill holes.

Pay attention that the drilling aid is ush with the edge of the door. Drill the four holes, carefully,

using a 3 mm wood drill bit to a maximum depth of 15mm. Use a depth stop or mark the depth on

the drill bit with adhesive tape.

When using an outer cylinder (C1/C2):

Firstly, drill a hole fully through the door leaf exactly in the middle of the circle of the drilling aid. To

ensure the outside of the door leaf does not crack, use the hole cutter rstly from the inside (approx. to

halfway through the door leaf) and then from the outside. Alternatively, x a small piece of wood to the

outside of the door with two clamps.

4 Fix the base plate (2) to the inside of the door using the screws (4) supplied. Before tightening the

screws to their nal torque, hold the lock case against the door leaf a few times to check the edges

are ush with the edge of the door.

Guarantee

The period of guarantee is 24 months. The period

of guarantee begins on the date of purchase. It is

essential to keep the purchase receipt and original

packaging. If a problem occurs, please visit our

Return Merchandise Authorization (RMA) in the

Support section of our web site at

www.olympia-vertrieb.de

In the case of further queries, please contact our

hotline 01805007514 (costs via German landline

at time of going to print: 14 ct/min., max. 42 ct/

min. via a mobile network).

Olympia Business Systems Vertriebs GmbH

Zum Kraftwerk 1 - 45527 Hattingen

v1.0, 10.2018

Art. No. RS50: 7046 (white) / 7047 (elegant appearance)

Art. No. RS50R: 7048 (white) / 7049 (elegant appearance)

Subject to change without prior notice.

Produkt Specifikationer

Mærke:	Olympia
Kategori:	Overvågningskamera
Model:	RS 50R

Har du brug for hjælp?

Hvis du har brug for hjælp til Olympia RS 50R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Olympia Manualer

Olympia OC 1280P Manual

11 Januar 2025

Olympia 5939 Manual

11 Januar 2025

Olympia TV 200 Manual

28 August 2024

Olympia BMD 210 Manual

15 August 2024

Olympia T300 Manual

15 August 2024

Olympia Protect 9065 Manual

14 August 2024

Olympia WL 100 Manual

13 August 2024

Olympia RS 50 Manual

12 August 2024

Olympia Protect 9571 Manual

12 August 2024

Olympia DC300 Manual

11 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

FLIR ioi HD CB-5222 Manual

30 Juli 2025

Eufy Cam S3 Pro Manual

30 Juli 2025

Telycam Vision+ 4KN 30X Manual

30 Juli 2025

Marshall Electronics CV630-BI Manual

30 Juli 2025

Telycam Vision+ SE Manual

30 Juli 2025

FLIR Ariel CC-3405 Manual

29 Juli 2025

FLIR Ariel CM-3505 Manual

29 Juli 2025

Axis Q6355-LE Manual

29 Juli 2025

Sony SNC-EMX52R Manual

29 Juli 2025

Hikvision DS-2CD3086G2H-LIU Manual

29 Juli 2025