On-Q evoQ 7000 Manual

On-Q Subwoofer evoQ 7000

Læs gratis den danske manual til On-Q evoQ 7000 (3 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om On-Q evoQ 7000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTRUCTION / INSTALLATION SHEET

evōQ™ 7000 In-Ceiling and In-Wall

Speakers

IS-0261 Rev. D

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

1. Introduction

On-Q/Legrand offers five (5) styles of evōQ™ 7000

Speakers; In-Ceiling, Dual Voice Coil, Angled In-

Ceiling, In-Wall, Outdoor, plus a 12” Sub-Woofer. There

are two sizes for both the standard In-Ceiling and In-

Wall styles (6.5” and 8”) see Figure 1. The Dual Voice

Coil speaker for smaller spaces, Angled In-Ceiling

speakers and Outdoor speakers are offered only with

6.5” drivers. All evōQ™ 7000 speakers are optimized

for high end home theater and high quality distributed

audio distribution (central sound). All models (except

the Sub-Woofer) are 2-way speakers that feature glass

fiber woofers and aluminum swivel tweeters. These

speakers come with dual templates with center

markings and paint rings. Optional speaker pre-

construction brackets are available for all models.

Note: *P/N HT7652, 6.5” In-Ceiling Dual Voice Coil

Speaker, P/N HT7655 6.5” Angled In-Ceiling

Speaker, P/N HT7653-WH/BK Outdoor Speakers and

P/N HT7124, 12” Sub-Woofer, are for reference only

and NOT part of this instruction sheet. See

Instruction Sheets IS-0262, IS-0393, IS-0263 and IS-

0264 (respectively).

Disclaimer: Make sure you are in compliance with local

building codes before installing these speakers.

2. Description

The On-Q/Legrand evōQ™ 7000 speakers are made of a tough semi-flexible plastic frames that feature a built in

foam gasket to minimize vibration and maximize seal-ability. They also feature a perforated metal grill with a

scrim cloth to enhance the speakers appearance once installed . All evóQ speakers, except sub woofers, are

paint-able and come with painting shields to protect the drivers while painting. These speakers are suitable for

moisture rich environments. They also feature flip out tabs for easy installation and removal. The On-Q/Legrand

evōQ™ 7000 speakers include a switch under the cover labeled “Treb” that has a (-) setting for bright rooms with

hard surfaces or (+) setting for damped rooms with low reflections due to carpet, drapes, and upholstered

furniture. They also include a ½” knockout for an IR target (not included).

3. Installation

Installation of the evōQ™ 7000 speakers is best accomplished at multiple times during new construction, at

“Rough-in” before the drywall is installed, and at “Trim-out” after the drywall is installed and painted.

A. “Rough-in” steps:

NOTE: It is recommended that a minimum of 16 gauge, 2 conductor wire be

used for most applications from the amplifier or volume control to the speaker.

Different gauges can, and should, be used based upon the distance of the

intended run or quality of installation ( )see Figure 2 .

Distance Gauge

<10 Feet 18

10-50 Feet 16

>50 Feet 14

Speaker Wire

Gau

e Selection Chart

Figure 2

Figure 1

6.5” - P/N HT7650 (ea)

8’ - P/N HT7800 (ea)

6.5” - P/N HT7651 (ea)

8” - P/N HT7801 (ea)

In-Ceiling Style

(shown w/o grill)

In-Wall Style

(shown w/o grill)

Dual Voice Coil Style

(not shown)

ngled In-Ceiling Style

(not shown)

12” Sub-Woofe

(not shown)

6.5” DVC - P/N HT7652 (ea)

6.5” Angled - P/N HT7655 (ea)

6.5” Outdoo

Speake

(not shown)

6.5” Outdoor - P/N HT7653-WH (ea)

6.5” Outdoor - P/N HT7653-BK (ea)

12” Sub - P/N HT7124 (ea)

INSTRUCTION / INSTALLATION SHEET

evōQ™ 7000 In-Ceiling and In-Wall

Speakers

IS-0261 Rev. D

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

NOTE: All On-Q/Legrand lyriQ™ Audio components accommodate wire gauges from 18 to 14.

1. Run x/2 conductor (x=gauge preference) stranded speaker wire from the distribution/volume control

to the speaker location (pre-wiring).

2. If an On-Q Speaker Pre-Construction Bracket is to be used, skip to

Step “5” and refer to IS-0243 for detailed instructions.

3. If pre-wiring without using the On-Q Pre-Construction Speaker

Brackets, leave 4 to 6 feet of wire at the speakers intended location.

Use a strip of cardboard stapled to the joints/studs with a hole

through it as a wire place holder for the drywall installers if

installation of the speakers is intended (see Figure 3).

4. After drywall and/or painting is complete, push wire through hole,

center template over hole, mark with a pencil and cut out with a dry-

wall knife.

5. When using the On-Q Pre-Construction Bracket (see

Figure 4), leave a coil of speaker wire on top of the

bracket coiled around the speaker mounting hole. There

are clips on the corner of the bracket to secure the

speaker wire. Leave enough speaker wire to be able to

pull the wire through the bracket and comfortably

connect the wire to the speaker after the drywall is

installed. Strip off 3 inches or so of the speaker cable

jacket to expose the positive and negative insulated

wires. Strip 3/8-1/2 inch of insulation off of these

conductors.

6. It is recommended to place insulation behind the

speaker to provide some damping for the woofer driver.

This will yield the best possible sound. On-Q

recommends using poly-encapsulated insulation such as

Johns Manville Comfort Therm®. If a defined, consistent

sound is desired from both speakers in a space, blocking

can be installed to yield the ideal cubic footage for each

driver. Insulation would then be put in this space during

speaker installation. Refer to blocking chart for

details.

7. If installing speakers in a space with an attic above it is

recommended that the speakers be boxed in with 1/2 inch

MDF (medium density fiber board) or plywood with

insulation installed. This will provide a defined acoustic

space and protect the speaker. The best possible sound

will be achieved by doing this. Refer to the blocking

chart for details.

Note: Make sure you are in compliance with local building codes before installing this speaker in

an attic space.

Figure 4

Figure 3

Blocking

Distance

Produkt Specifikationer

Mærke:	On-Q
Kategori:	Subwoofer
Model:	evoQ 7000

Har du brug for hjælp?

Hvis du har brug for hjælp til On-Q evoQ 7000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Subwoofer On-Q Manualer

On-Q evoQ 7000 Manual

18 August 2024

Subwoofer Manualer

Nyeste Subwoofer Manualer

Pioneer TS-W32D4 Manual

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

Syrincs D18 Sub Manual

30 Juli 2025

AudioControl Epicx EPICX8D2 Manual

30 Juli 2025

SSL GSW12D Manual

29 Juli 2025

AudioControl Epicx EPICX10D2 Manual

29 Juli 2025

Sirus Elephant 10 Black Manual

29 Juli 2025