OSD Audio Speaker Selector 12 Manual

OSD Audio Skifte Speaker Selector 12

Læs gratis den danske manual til OSD Audio Speaker Selector 12 (1 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13 anmeldelser. Har du et spørgsmål om OSD Audio Speaker Selector 12, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

TSM8/ TSM12

Autoformer Based Speaker Selector

Instruction Manual

A U D I O

OSD

Thank you for giving OSD AUDIO the chance to earn your business! We are condent you will nd that OSD oers an outstanding combination of performance

and value in everything we make. To ensure you get the most out of your new TSM8/ TSM12, please take a moment to read this manual before you get started.

OSD Audio • 1405 t • ea • A • 92821 • • Tel (562) 697-2600 • Pioneer S Br C www.osdaudio.com Fax (562) 697-2668

1. Connections

To connect the amplifiers/receivers to the speaker selector, remove the AMP A/B connector by firmly pulling it out of its 8-pole socket. Strip ” of insulation from the end 1/4

of each wire. Tightly twist the end of each wire until no frayed ends remain. Insert each wire into the appropriate hole on the removeable terminals (matching up the

polarity). Use a small screwdriver to tighten each wire into the AMP A/B connector. Insert the connector plug into the socket and lock in place Be sure not to reverse .

these connections or the will not function properly. TSM12 /TSM8 Follow the same procedure to connect each ir spa of peakers to pthe ap ropriate speaker connector terminal,

observi p per channng ro el and polarity. If external volume control s are used, t sconnec peaker wire rfrom the app opriate speaker connector on the TSM12/ TSM8 to the volume

co ront l input. r tSpeake connec ions scan upport lti e rs mu pl speaker pai wired in pa rallel or series, provided thei r comb imined ped ncea is a minimum of 4 s.ohm

2. Operation

To u fe oens re sa peration of the amplifie r, an impedance level must fi rst be selected using the rotary switch llabe ed speaker pair tloca ed on the of rear the unit. This switch should

be to e l nset th tota um spber of eaker pair s i be ng connec edt

to the un it. Set the switch fbased on the ollowing conditions:

If the mpli a fier and the spea kers are both 4 t tohm or 8 ohm, se he ota r ry switch to the nu mber of pair of speakers e connected to th TSM12 /TSM8.

If the mpli a fier is 8 tohm and he speakers are 4 tohm, set he rotary switch to T CE WI the numbe r of ir spa of peaker connec eds t to TSM12 /TSM.8

If e r 4 oth amplifie is hms and akethe spe rs are 8 oh , set the ro ry switch to HAms ta LF the nu mber of pai r of speake connected to the rs TSM12 /TSM8.

After ng setti the proper impedance level, the speakers can be turned on and off in any combination.

S ch wwit bet een th e A and B pam lifiers, the push AMP A / AMP B t n lobu to ca edt on the fr .ont panel

3. Setting System Volume

It is important to properly adjust an impedance-matching system to avoid distortion or DC clipping (DC voltage will be produce d from aan mp ifiel r wthat is over orked or that has an

improper lo ad). These can cause an amplifier rece/ iver to go into protection, an d can ocause autof rmers on volume controls to heat up, damag ing sys emt compo entn s. To set up

the system, the amplifier/rece iver volume d shoul be at its lowest setting, and the in- wall/selector volume co rnt ol sho uld st s be at the highe etting. Slowly adj ust the

amplifie ivr/rece er volume to a vle el that is the aacceptable for mplifier to pro ce du without clipping .

100 Watts per channels RMS continuous

200 Watts per channel average

300 Watts per channel peak

17” x 7.1” x 2.9”

Up to 14 Gauge wire

2 Years

Listening Zones:

8 (TSM8)

12 (TSM12)

Power:

Dimensions: L x W x H:

Cable Gauge:

Warranty:

100 Watts per channels RMS continuous

200 Watts per channel average

300 Watts per channel peak

17” x 7.1” x 2.9”

Up to 14 Gauge wire

2 Years

A U D I O

OSD

7-8

3-4

Number of

Speaker Pair

AMPLIFIERS

SPEAKERS

AMP A

AMP B

AMPLIFIERS

PAIR1PAIR2

PAIR3

PAIR4

PAIR5PAIR6

PAIR7

PAIR8

Produkt Specifikationer

Mærke:	OSD Audio
Kategori:	Skifte
Model:	Speaker Selector 12
Bredde:	431.8 mm
Dybde:	209.55 mm
Højde:	73 mm
Vægt:	4990 g
Produktfarve:	Sort
Kontroltype:	Knapper
Lyd-output kanaler:	8 kanaler
Maksimal effekt pr. kanal:	300 W
Lyd, indgående kanaler:	2 kanaler
Minimum effekt pr. kanal:	100 W