Outdoor Connection Bedarra Manual

Outdoor Connection Fuld Bedarra

Læs gratis den danske manual til Outdoor Connection Bedarra (3 sider) i kategorien Fuld. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Outdoor Connection Bedarra, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

QUALITY YOU CAN SEE FEEL AND TRUST

BEDARRA DOME

TENT INSTRUCTIONS

1. Select a dry level area and clear the ground of any sharp or dangerous objects.

2. Spread out the floor of the inner tent

and peg out the four corners ensuring that

the tent is pulled out firm and square (be careful not to make it too taut). Peg out the

remaining pegging points. The adjustable straps on some of the peg loops should be set approximately in their middle position (not pulled up tight). Pulling all these

straps up tight may over stress the inner tent and cause some seams to start separating.

3. Assemble all the fibreglass poles. There will be 6 black poles and a ridge pole (a grey pole with a cross piece in the middle).

4. Above the door at each end there is a T piece that will be wrapped in a bag. Remove

the protective bags. Insert the ends of

the ridge pole into the T pieces. The longer

half of the ridge pole goes to the back of the tent (the end with side windows). Wrap the Velcro tie around the Cross pieces in the middle of the tent. (Make sure that the

reinforcing wire on the cross pieces are facing down towards the tent inner.)

5. Slide the short end of the black poles through the sleeves and insert the poles into the cross pieces in the middle and into

the T piece at

one end only

6. Stand up the poles at the end and then the middle. The bottom of the poles slide over a pin on the base of the tent. Two thirds of the tent should now be up.

7. Slide the remaining two black poles through the sleeves and insert the poles into the T piece. Once both sides are in stand up the poles and slide the ends over the pins.

You will have better access if you open the bottom of the door and stand just inside the tent.

8. Attach all tent clips to the upright poles. The inner tent is now complete and you are ready to fit the fly.

9. Position the fly over the tent and align it into place. Tie off the inside of the fly at the elbow at the top of the pole. Attach the Velcro tabs on the inside of the fly to the

poles.

10. With the doors of the fly zipped up peg out the fly ensuring an adequate gap between the fly and the inner. (Take care not to peg the fly too far out from the base as you

may distort the shape of the tent)

11. Peg out all the guy ropes.

12. Finally, fine tune the fly so it remains firm and positioned correctly over the tent. The adjustment straps at some peg points can be used for small adjustments but make

sure that the tent is not too tight as the tent seams can be damaged.

13. The Fly doors at each end of the tent can be erected as an awning. 3 adjustable poles are supplied for this purpose. When erected the awning tensioner strap near the

top of the door can be done up and tightened to take out the sag in t the centre pole is higher than the sides the awning. (Do not to over tighten this strap.) Ensure tha

which will allow some pitch for run off in light rain.

*****REVERSE THESE PROCEDURES TO LOWER THE TENT*****

Packing Instructions:

1. Make sure the inner tent and fly are COMPLETELY DRY and CLEAN before packing away.

2. Wrap the T pieces in their protective bags and foam. Pack the poles and pegs in their bags.

3. Fold the fly in half lengthwise and fold the ends in to form a rectangle. Then fold each end into the middle and continue folding until you have a long rectangle approx

80cm wide and 250cm long. The bottom of the fly should be at one end when folded.