Paasche VL-3AS Manual

Paasche Ikke kategoriseret VL-3AS

Læs gratis den danske manual til Paasche VL-3AS (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Paasche VL-3AS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTRUCTIONS AND PARTS LIST VL-10/23/2018

VL – Airbrush

Double Action - Internal Mix

Siphon Feed

INTRODUCTlON:

Paasche® model VL features hand crafted

construction using quality materials. The body

is machined brass, polished and chrome plated.

Fluid tips are nickel silver, needles are stainless

steel & the needle packing is PTFE. Preferred

by professional and hobbyist alike.

Airbrush Operation:

1. Press down on Trigger to release air and pull back on Trigger to control quantity of color.

2. To spray a ne line without heavy ends, start moving the airbrush without release of color. Then start

the color at the beginning of line and stop the color at the end, but continue the motion of the airbrush

after the color has stopped.

3. Practice until you can spray a ne line or a broad pattern without heavy build up at the beginning or

end of your strokes.

4. Speed of movement controls density of color and fading e󰀨ects at beginning and end of strokes.

5. For detail, hold the airbrush very close to the surface and then push down for air and pull back very

slowly on the Trigger to release a small amount of paint.

6. For background work and broad e󰀨ects, hold the airbrush away from the work surface and pull back

on Trigger to release required amount of color.

Head Sizes - Patterns - Fluid Thickness

Size 1 Size 3 Size 5 - Tip size .55mm -Tip size .73mm -Tip Size 1.06mm

- Pencil Line to 1’’ patterns -1/16’’ to 1-1/2’’ patterns-1/32’’ to 1-1/2’’ patterns

-Paint thinned further than 3 & 5 -Thicker paint than size 1 -Thicker paint than size 3

Working Pressures:

• Operating pressures 20-55 PSI; Maximum pressure 75 PSI

• 20-30 PSI is best for detail spraying w/ properly thinned paint

• Use the higher pressures for thicker material where ne detail is not critical or thin the paint to allow

lower pressures.

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with the index nger comfortably over the Trigger.

1. Attach airhose to air supply and to airbrush. If using a regulator, set pressure between 20 -30 PSI.

2. Attach the color cup or bottle assembly to color socket.

REMOVING/REPLAClNG THE NEEDLE AND HANDLE :

1. Unscrew the handle and loosen the Locknut #34 by turning counterclockwise. Depress the Trigger

#7 and hold in Down position while removing or inserting the needle. This assures the needle moves

freely through the trigger. Gently remove the needle, rotating if necessary, Do NOT force out!

2. Inspect the condition of the needle. If it is bent or misshapen in any way, replace it with a new needle.

A bent needle can damage or split the Tip #3 causing bubbles or a rough spray pattern.

3. Hold trigger in DOWN position, insert the new needle into the Rocker Assembly #28. Gently push

needle through, rotating if necessary. until the needle stops in the front of the tip.

4. Release trigger and tighten locknut by turning clockwise.

REPLACING THE TRIGGER:

( If the Trigger #7 is removed, it must be replaced inside the airbrush shell, before the Rocker Assembly #28

and needle are re-inserted. )

1. Hold the trigger so the opening in the lever is in-line with the opening in the end of the airbrush shell

and the at side of the trigger stem is to the rear.

2. Insert trigger so the bottom of the stem covers the round top of the valve plunger.

REPLACING THE TIP:

1. Remove handle, loosen Locknut #34 and withdraw needle about one inch (1”).

2. Un-screw the Head #2 and remove. The Tip #3 can now be easily removed by hand. If stuck in shell tap

lightly with wrench.

3. Place a new tip into position and tighten head to shell . Push needle forward until itwith a wrench

seats fully forward in tip and tighten locknut.

Paasche Airbrush Co. 9511 58th Place Kenosha, WI. 53144 Phone:773/867-9191

Email:info@paascheairbrush.com

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	VL-3AS

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche VL-3AS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025