Panduit CT-1570 Manual

Panduit Ikke kategoriseret CT-1570

Læs gratis den danske manual til Panduit CT-1570 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Panduit CT-1570, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Part No. CT-1570

OPERATION INSTRUCTIONS

Contour Crimp

CONTROLLED CYCLE

CRIMPING TOOL

Crimps most Panduit #22 - #10 AWG

and 0,5 - 6,0 mm

non-insulated terminals,

disconnects, and specific

non-insulated splices.

Provides UL Listed and CSA Certified terminations

with applicable Panduit terminals.

NON-INSULATED TERMINAL AND

DISCONNECT CRIMPING INSTRUCTIONS

1. With the handles in the open position, insert

the terminal or disconnect in the proper crimp

pocket (See Figure 1). For butted or brazed

seam terminals, place the seam opposite of

the indentor. Center the terminal barrel in the

crimp pocket (See Figure 2). Refer to product

packaging for selection of proper crimp pocket.

2. Close the tool handles until the terminal or

disconnect barrel is held snugly in position—

do not deform the barrel.

3. Insert the stripped wire into the terminal or

disconnect until the wire stops. Refer to

product packaging for wire strip length.

NON-INSULATED SPLICE

CRIMPING INSTRUCTIONS

OPERATION INSTRUCTIONS

PA22153A05

Rev.: 06 4-2017

CT-1570

Figure 1

Figure 2

CRIMP POCKETS FOR

PanTerm NON-INSULATED

terminals, disconnects and

specific splices. Refer to

product packaging for wire

range and proper crimp

pocket. Crimp pockets are

identified with applicable

wire range.

1. With the handles in the open position,

insert the splice into the proper crimp

pocket (See Figure 1) with the indentor

centered over the half of the barrel to be

terminated first (See Figure 3). Refer to

product packaging for selection of

proper crimp pocket.

2. Close handles until the barrel is held

snugly in position—do not deform the

barrel.

3. Insert the stripped wire into the splice

until the wire stops and it is visible

through the inspection opening. Crimp

the splice by closing the handles until

the controlled cycle mechanism

releases. Refer to product packaging for

wire strip length.

4. Remove the splice and repeat operation

for crimping the other end of the splice.

Die Closure Alignment

(not a crimp pocket)

4. Crimp the terminal or disconnect by closing the handles until the controlled cycle mechanism releases. Upon

release, the handles will open automatically and the crimped terminal or disconnect can be removed.

After crimping, inspect that the crimp is centered on the disconnect barrel in order to achieve

optimal pullout performance.

Email:

techsupport@panduit.com

EU Website: www.panduit.com/emea

EU Email: emeatoolservicecenter@panduit.com

Technical Support

Tel: 1-800-777-3300

Panduit Europe • EMEA Service Center

Tel: 31 546 580 452 • Fax: 31 546 580 441

CAUTION: Verify power is “OFF” before

working on wiring with this tool. The

cushioned grips are for the user’s

comfort, and are not intended to

insulate against shock while working

on live electrical circuits.

Page: 1 of 2

www.panduit.com

Cushioned Handle Grips

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is

completed.

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	CT-1570

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit CT-1570 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit MIW187 Manual

8 Januar 2026

Panduit CBXQ2AW Manual

8 Januar 2026

Panduit FHS9N-12-10N Manual

8 Januar 2026

Panduit PSL-BV1 Manual

8 Januar 2026

Panduit DAP4BC-G5-6 Manual

7 Januar 2026

Panduit CT-1015 Manual

7 Januar 2026

Panduit FC2ZO-24-10AF Manual

7 Januar 2026

Panduit CT-1570 Manual

7 Januar 2026

Panduit DAP4BC-G3-5 Manual

7 Januar 2026

Panduit C2FAB08A1200B1 Manual

7 Januar 2026

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Canarm VKM150 Manual

8 Januar 2026

Canarm KE-08SX Manual

8 Januar 2026

Velux TLR 014 Manual

8 Januar 2026

Ikea BODBYN 105.686.00 Manual

8 Januar 2026

Canarm 925 Manual

8 Januar 2026

Ikea DAGGKAPRIFOL 606.179.38 Manual

8 Januar 2026

Ikea BODBYN 405.685.90 Manual

8 Januar 2026

Ikea VALASJÖN 506.199.47 Manual

8 Januar 2026

WAC Lighting JTK-103 Manual

8 Januar 2026

Vaxcel Canton T0748 Manual

8 Januar 2026