Panduit CT-160 Manual

Panduit Tang CT-160

Læs gratis den danske manual til Panduit CT-160 (2 sider) i kategorien Tang. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Panduit CT-160, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CAUTION:
Verify power is “OFF” before working on wiring with this tool.
The plastic grips are for the user’s comfort,
and are not intended to insulate against electrical shock
while working on live electrical circuits.
CT-160
CRIMPING TOOL
OPERATION INSTRUCTIONS
10-32
.80
1.0
1.3
1.6
2.0
2
.6
MM
CUT COPPER ONL
Y
22
20
18
16
14
1
2
10
AWG
8-32
6
-32
M5
M4
M3
.5
INSULA
TION
AUTO
7
-8
MM
INS
INS
NO
N
INS
NO
N INS
12
-1 0
22
-1 4
12
-1 0
22
-1 4
CLO ESHERE
I
N
S
E
R
T
S
C
R
E
W
S
T
H
I
S
S
I
D
E
CT-160
NON-INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper non-
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Repeat for other end of butt splice.
Page: 1 of 2
PA24427A01
REV.: 02 5-2014
OPERATION INSTRUCTIONS
© Panduit Corp. 2014
CT-160
For Technical Support:
1-888-506-5400, ext. 83255
E-mail:
techsupport@panduit.com
See product packaging or contact Customer Service for
UL/CSA approved tooling/product combinations.
INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Close insulation if desired.
6. Repeat for other end of butt splice.
WIRE STRIPPER for removing plastic or
rubber wire insulation. Strip length should
allow a minimum of 1/32” of conductor to
extend beyond terminal barrel.
WIRE CUTTER for No. 10 AWG and
smaller copper wire.
CUTTERS for machine screws of sizes
shown. Open handles, thread screw in this
side. Close handles to cut screw.
CRIMPING POCKETS for Pan-Term non-
insulated and insulated terminals,
disconnects, splices and wire joints on No.
22 to 10 AWG stranded wire. See product
packaging for proper crimping pockets.
This tool is made of hardened steel and is
protected with a light coat of oil.
NON-INSULATED AND INSULATED
PARALLEL SPLICE INSTRUCTIONS
1. Insert stripped wire into each end of the
parallel splice. (See product packaging
for proper strip lengths.)
2. Locate parallel splice in proper crimp
pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
CRIMP POCKET
CRIMP POCKET
CRIMP POCKET
NON-INSULATED
INSULATED
www.panduit.com
Page: 2 of 2
OPERATION INSTRUCTIONS
NON-INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
non-insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
NON-INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper non-insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
CRIMP POCKET
CRIMP POCKET CRIMP POCKET
CRIMP POCKET
CT-160
© Panduit Corp. 2014
NOTE:
In the interest of higher
quality and value, Panduit is
constantly improving and
updating our products.
Consequently, pictures herein may
vary from the actual product.

Produkt Specifikationer

Mærke: Panduit
Kategori: Tang
Model: CT-160

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit CT-160 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Tang Panduit Manualer

Panduit

Panduit CT-160 Manual

16 August 2024
Panduit

Panduit CT-1700 Manual

13 August 2024

Tang Manualer

Nyeste Tang Manualer

Scarlett

Scarlett SC-HS60599 Manual

8 December 2024
Scarlett

Scarlett SC-HS60T60 Manual

8 December 2024
Scarlett

Scarlett SC-HS60T50 Manual

8 December 2024
Extron

Extron CTU 45 Manual

5 September 2024
Scarlett

Scarlett SC-HS60T52 Manual

4 September 2024
Fixpoint

Fixpoint 77124 Manual

1 September 2024
Fixpoint

Fixpoint WZ CRIMP 09 Manual

1 September 2024
Scarlett

Scarlett SC-HS60604 Manual

30 August 2024
Scarlett

Scarlett SC-HS60505 Manual

29 August 2024
Weidmüller

Weidmüller SE HD 160 Manual

27 August 2024