Panduit HST1.5-48-5-2Y Manual

Panduit Ikke kategoriseret HST1.5-48-5-2Y

Læs gratis den danske manual til Panduit HST1.5-48-5-2Y (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Panduit HST1.5-48-5-2Y, eller vil du spørge andre brugere om produktet?

Side 1/2
HST Thick Wall Heat Shrink
INSTALLATION INSTRUCTIONS IN003
© Panduit Corp. 2013
6R72
(HST2.7 and smaller)
(HST2.7 and smaller)
Black Only
(HST2.7 and smaller)
Sunlight Resistant
VW-1
WARNING:
A. IN-LINE SPLICE CONNECTOR
minimum overlap length (2 Inches) __________________________________ x 2= ________________
splice length from manufacturer ......................................................................... = ________________
total minimum tube length (add) ......................................................................... = ________________
Splice
Overlap
Overlap
Tube Length
Lug
Overlap
Tube Length
2. Clean the cable which will be covered by the tube. Lightly sanding the surface is recommended.
3. Remove the cable insulation length for the connector according to the manufacturer's instructions.
4. Place the tube over the cable.
5. Install the connector according to the manufacturer's instructions.
6. Preheat the cable insulation where it will contact the tube.
7. Center the tube over the splice, or position it against the lug tongue.
8. Starting in the center the tube using a broad soft flame and working your way out to the ends, shrink
which will cause the product to recover. Do not scorch the tube.
A. IN-LINE SPLICE CONNECTOR
Shrink from the center of the
tube t ard the ends.ow
B. LUG CONNECTOR
Shrink from the lug end t ard the opposite end.ow
The shrink is complete when adhesive oozes from between the tube and the cable and/or the lug.
Page 1 of 2
B. LUG CONNECTOR
minimum overlap length (2 inches) ..................................................................... = ______________
conductor strip length from manufacturer ........................................................... = ______________
total minimum tube length (add) ......................................................................... = ______________
For Technical Support: www.panduit.com/resources/install_maintain.asp
4
2
"2"2"2
244528
torch or hot air gun. Minimum recommended shrink temperature is 248° F (120° C). Use higher
temperatures to recover faster. Continually move the source around the diameter of the tube,heat
Follow installation instructions carefully to avoid charring or burning. Use adequate ventilation.
Consult Material Safety Data Sheet for further information.


Produkt Specifikationer

Mærke: Panduit
Kategori: Ikke kategoriseret
Model: HST1.5-48-5-2Y
Type: Varmekrympet rør
Antal pr. pakke: 5 stk
Produktfarve: Rød
Rørlængde: 1219.2 mm
Diameter før krympning: 38.1 mm
Diameter efter krympning: 12.7 mm

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit HST1.5-48-5-2Y stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Panduit Manualer

Panduit

Panduit VS2-NET Manual

29 November 2025
Panduit

Panduit PWBCB12 Manual

18 November 2025
Panduit

Panduit NCMHF1 Manual

31 Oktober 2025
Panduit

Panduit CEG-13X1 Manual

9 Oktober 2025
Panduit

Panduit PR2HF1 Manual

9 Oktober 2025
Panduit

Panduit CEST1-D3 Manual

8 Oktober 2025
Panduit

Panduit CBEWHY Manual

8 Oktober 2025
Panduit

Panduit CEG-05X2 Manual

8 Oktober 2025
Panduit

Panduit CEST2-A6 Manual

8 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BEKO

BEKO DVS15022W Manual

7 December 2025
Opticis

Opticis OPS-xyz Manual

7 December 2025
Opticis

Opticis BR-500 Manual

7 December 2025
Opticis

Opticis DPOC-14N Manual

7 December 2025
FiiO

FiiO BR15 R2R Manual

7 December 2025
Fostex

Fostex FE83NV2 Manual

7 December 2025
Fostex

Fostex EN15 Manual

7 December 2025
Advantech

Advantech iDAQ-731D Manual

7 December 2025
Bosch

Bosch MAF462C0 Manual

7 December 2025