Panduit HST3.0-48-2 Manual

Panduit Ikke kategoriseret HST3.0-48-2

Læs gratis den danske manual til Panduit HST3.0-48-2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Panduit HST3.0-48-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

HST Thick Wall Heat Shrink

INSTALLATION INSTRUCTIONS IN003

6R72

(HST2.7 and smaller)

Black Only

(HST2.7 and smaller)

Sunlight Resistant

VW-1

WARNING:

1. Calculate the minimum tube length.

A. IN-LINE SPLICE CONNECTOR

minimum overlap length (2 Inches) __________________________________ x 2= ________________

splice length from manufacturer ......................................................................... = ________________

total minimum tube length (add) ......................................................................... = ________________

Splice

Overlap

Tube Length

Lug

Overlap

Tube Length

2. Clean the cable which will be covered by the tube. Lightly sanding the surface is recommended.

3. Remove the cable insulation length for the connector according to the manufacturer's instructions.

4. Place the tube over the cable.

5. Install the connector according to the manufacturer's instructions.

6. Preheat the cable insulation where it will contact the tube.

7. Center the tube over the splice, or position it against the lug tongue.

8. Starting in the center the tube using a broad soft flame and working your way out to the ends, shrink

which will cause the product to recover. Do not scorch the tube.

A. IN-LINE SPLICE CONNECTOR

Shrink from the center of the

tube t ard the ends.ow

B. LUG CONNECTOR

Shrink from the lug end t ard the opposite end.ow

The shrink is complete when adhesive oozes from between the tube and the cable and/or the lug.

Page 1 of 2

B. LUG CONNECTOR

minimum overlap length (2 inches) ..................................................................... = ______________

conductor strip length from manufacturer ........................................................... = ______________

total minimum tube length (add) ......................................................................... = ______________

For Technical Support: www.panduit.com/resources/install_maintain.asp

"2"2"2

244528

torch or hot air gun. Minimum recommended shrink temperature is 248° F (120° C). Use higher

temperatures to recover faster. Continually move the source around the diameter of the tube,heat

Follow installation instructions carefully to avoid charring or burning. Use adequate ventilation.

Consult Material Safety Data Sheet for further information.

61#-21#15.0

HST0.4 (13.0) (4.1) (4-16)

1#-8#0.75 0.24

0.35

0.63

0.87

0.16

HST0.8 (19.1) (6.1) (10-55)

0/4#-2#01.1

HST1.1 (27.9) (8.9) (35-120)

004-0/1#74.005.1

HST1.5 (38.1) (11.91) (55-185)

006-05200.2

HST2.0 (50.8) (16.0) (125-300)

0001-00607.2

HST2.7 (68.6) (22.1) (300-500)

0521-05700.100.3

HST3.0

(76.2) (25.4) (400-625)

+0091.203.50

HST3.5

(88.9) (30.5) (400+)

These sizes are not UL Recognized. UL Listed or CSA Certified.

**It is always best practice to use the largest HST product which has a “Maximum Recovered I.D.” smaller than the

bundle diameter. This will insure maximum insulation thickness and best protection for the splice.

All parts available in black, some available in red. Contact customer service for details.

Product Size

Minimum Expand I.D.

Inches (mm)

Maximum Recov. I.D.

Inches (mm)**

Typical Conductor

Size Range

AWG/MCM (mm2)**

INSTALLATION INSTRUCTIONS IN003

www.panduit.com

For instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

E-mail:

techsupport@panduit.com

Phone:

866-405-6654

Panduit thick wall heat shrink tubing, HST, is UL listed and CSA certified. UL requires UL 486A or B listed

connectors and CSA requires C22.2, No. 65 certified connectors. For use in wet or damp locations.

Rev. 05Page 2 of 2

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	HST3.0-48-2
Type:	Varmekrympet rør
Antal pr. pakke:	2 stk
Produktfarve:	Sort
Rørlængde:	1219.2 mm
Diameter før krympning:	76.2 mm
Diameter efter krympning:	25.4 mm