Paxton Easyprox nano Manual

Paxton Sikkerhed adgangskontrolsystem Easyprox nano

Læs gratis den danske manual til Paxton Easyprox nano (8 sider) i kategorien Sikkerhed adgangskontrolsystem. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Paxton Easyprox nano, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Page 1

01/28/2013

Parts list

Tools List

Power Drill

Drill bits 3/8", 1".

Philips screwdriver

Hacksaw for cutting bolts

Hammer / Mallet

Chisel 1 inch

Stanley knife

Adhesive tape

Pencil

Tape measure

8 mm spanner (supplied)

2 mm Allen key (supplied)

1) Front Lock Assembly

2) Rear Lock Assembly

3) Rubber Escutcheon x2

4) Left and Right Handles

5) Battery Pack

6) Tubular Mortice Lock

7) Square Drive Bar

8) 8 mm and 5/16" Sleeves

9) 2 mm Allen Key

10) 8 mm Spanner

11) Strike Plate Backbox

12) Strike Plate

13) Long Mounting Screws x4

14) Short Mounting Screws x4

This unit is for Indoor use only

Technical Support

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

1.800.672.7298 supportUS@paxton-access.com

Ins-40107-US Easyprox nano - UL

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

Net2Air Site Surveyor (690-200-US).

This access control unit uses wireless communication.

It is recommended that a Net2Air site surveyor is

used to determine the best position for the bridge

and control units.

This wireless unit requires a Net2Air bridge to

communicate with the server PC.

1 2

6 7 8 9 10 11 12

13 14

3 4

Part number Description

746-284-US Easyprox nano access control unit

Paxton

Page 2

Decide on the lock height and mark this on the door.

Fold the template along one dotted line and tape it to

the door with the 'Centreline of Latch' at the required

height. Mark the 4 x 3/8" and 1 x 1" holes. Remove the

template, fold along the other dotted line and apply it

to the other side of the door at the same height. Mark

the holes as before.

Remove the access plate at the rear of the unit by

removing the top standoff screws. Push the battery

pack lead onto the white power plug.

Fit the battery pack and replace the access plate.

Installing the hardware

Step 1 - Marking out

Step 2 - Drilling

Step 3 - Fitting the latch

Step 4 - Fitting the battery pack

Drill a 1" hole in the door edge at least 3 1/4" deep to

accept the latch.

Drill the 4 x 3/8" holes for the mounting screws and a

1" hole for the square bar. To ensure accuracy you

should drill these holes from both sides of the door

towards the centre. This also avoids the risk of

damaging the door face when the drill breaks through.

Slide in the latch and draw around the faceplate.

Remove the latch and score the outline with a Stanley

knife to avoid splitting the wood when chiselling.

Chisel a rebate allowing a ush t for the latch. Re-t

the latch with the plunger facing away from the door

frame and secure with two latch screws.

Cut the square bar to length (Door thickness + 3/4")

and slide into the latch.

The unit is now active and is LOCKED with the

handle disconnected.

Where possible, the unit should now be enrolled

BEFORE mounting it on the door.

Produkt Specifikationer

Mærke:	Paxton
Kategori:	Sikkerhed adgangskontrolsystem
Model:	Easyprox nano
Bredde:	150 mm
Dybde:	72 mm
Højde:	194 mm
Produktfarve:	Sort, sølv
Driftstemperatur (T-T):	0 - 55 °C
Driftsfrekvens:	2405 MHz