Peak PKC0J6 Manual

Peak Batterioplader PKC0J6

Læs gratis den danske manual til Peak PKC0J6 (7 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 93 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 47 anmeldelser. Har du et spørgsmål om Peak PKC0J6, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
600 Peak Amp
Jump-Starter
Model No.: PKC0J6
Owner’s Manual
and Warranty Information
Read these instructions completely before using this product.
Retain this Owner’s Manual for future reference.
 Do not expose battery to fi re or intense heat since it can explode.
 Before recycling or disposing of a battery, protect exposed terminals with heavy-duty electrical tape
to prevent shorting (shorting can result in personal injury or fi re).
 Always wear protective eyewear when using this product. Contact with battery acid can cause
blindness and/or severe chemical burns.
 Follow these fi rst aid procedures in case of accidental contact with battery acid.
FIRST AID
SKIN: Wash skin thoroughly if battery acid comes in contact with skin. Seek medical attention
immediately.
EYES: Flush eyes with cool water for at least ten minutes. Seek medical attention immediately.
CONTACT POISON CONTROL CENTER IMMEDIATELY IF INGESTED.
 Never touch battery clamps together or to a common piece of metal. Sparking, explosion or
damage to the unit can result. Always store the battery clamps on the appropriate case clamp posts
on the back of the unit after use.
 Place this unit as far away from the battery being charged as the charging cables will permit.
 When using the Jump-Starter close to the vehicle’s battery and engine, place the unit on a fl at,
stable surface, and keep all clamps, cords, clothing and body parts away from moving parts of the
vehicle.
 Follow these instructions and those published by the battery manufacturer and manufacturer of
any equipment you intend to use near the battery. Pay attention to all hazard precautions on these
products and on the engine before charging.
 This system is designed to be used only on vehicles with a 12-volt DC battery system. Do not
connect to a 6-volt or 24-volt battery system.
 Remove all jewelry or metal objects that could cause short circuits or react with battery acid. A lead-
acid battery produces a short-circuit current high enough to weld a ring or other similar objects to
metal, causing a severe burn.
 When w orking on electrical equipment, always ensure someone is nearby to help you in an
emergency.
 Keep a supply of baking soda on hand when working on batteries. Baking soda neutralizes lead-
acid battery electrolyte.
All messages that follow have NOTICE level hazards. Failure to comply could
result in property damage.
 Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-
started. Before jump-starting, read the vehicle’s owner’s manual to con fi rm that external-starting
assistance is suitable.
 Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after
the recommended number of attempts, discontinue these jump-start procedures and look for other
problems that may need to be corrected.
 This Jump-Star ter is not designed to be used as a replacement for a vehicle’s battery. Do not
attempt to operate a vehicle that does not have a battery installed.
 After connecting the batter y charging clamps to the discharged battery and before turning on the
jump-starter ON/OFF switch, check the power/polarity indicator light on the front of the unit. If the
light is GREEN, the clamp connections are correct. If the light is RED and an alarm sounds, the
clamp connections are incorrect and need to be reversed.
 This Jump-Starter is delivered in a partially charged state. Fully charge unit with the supplied
110/120-volt AC charger to the recommended maximum and initial charge time of 24 hours.
Thereafter, an AC typical charge time is 8 to 12 hours when using the AC charger.
 Although this unit contains a sealed batter y, it is recommended that unit be kept upright during
storage, use and recharging. To avoid possible damage that may shorten the unit’s working life,
protect it from direct sunlight, direct heat and/or moisture.
 Never allow battery acid to come in contact with this unit.
 All ON/OFF switches should be in the OFF position when charging the Jump-Starter or when not in
use. Make sure all switches are in the OFF position before connecting to a power source or load.
 Do not use any accessory that is not recommended or provided by the manufacturer.

Produkt Specifikationer

Mærke: Peak
Kategori: Batterioplader
Model: PKC0J6

Har du brug for hjælp?

Hvis du har brug for hjælp til Peak PKC0J6 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Batterioplader Peak Manualer

Peak

Peak PKC0J6 Manual

12 August 2024
Peak

Peak PKC0AZ Manual

6 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Watson

Watson MDC-1546 Manual

13 August 2025
Watson

Watson MDC-4234 Manual

13 August 2025
Nedis

Nedis EVCA22KWBK50 Manual

13 August 2025
Watson

Watson MDC-4228 Manual

13 August 2025
Watson

Watson MDC-1537 Manual

13 August 2025
Alogic

Alogic Rapid Power WCG1X30 Manual

13 August 2025
Watson

Watson MDC-4237 Manual

13 August 2025
Alogic

Alogic WCG2X40 Manual

13 August 2025
Watson

Watson MDC-3418 Manual

13 August 2025
Watson

Watson DLCX Manual

13 August 2025