PECO SB200-001 Manual

PECO Termostat SB200-001

Læs gratis den danske manual til PECO SB200-001 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om PECO SB200-001, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION & WALK TEST

GENERAL

The SB200-001 is an occupancy sensor designed for

automatic HVAC system control. This sensor provides a

changeover (form C) relay signal output for fan coil controller

to activate/deactivate the operation of fan coil automatically.

This sensor can be wall or corner mounted with 110°, 50 ft

(15m) detection range.

INSTALLATION & WALK TEST

Installation

1. Mount the base of mounting bracket on the selected

position. Route the cable through the access tunnel

of mounting bracket.

2. Open the front cover by loosening the locking screw

at the bottom. Route the cable into the unit and

assemble the mounting bracket with the unit.

Wiring Diagram

 NC-COM-NO: Output for ON-

OFF control of fan coil operation.

Dry contact signal.

 24 V: Power supply (non-polarity)

4. Replace the front cover and then perform the walk

test.

Walk Test

Apply the power supply to the sensor and wait for about 45

seconds to warm unit up. The LED will blink (long-short)

during warm up period. Ensure the jumper head connectors

of ON and OFF delays are placed on “A” position (shortest

delay). Walk across the detection zones (invisible) at normal

speed. The LED will light whenever the sensor detects the

motion. Note: If any jumper is not properly placed, the LED

will blink.

Ceiling Mount

Wall Mount

Do not install where unit is

exposed to direct sunlight or

directly above strong sourcesof

heat.

Make sure the detection area does

not have any obstruction (plants,

large pieces of furniture, curtains

etc.) which may block the

detection.

INSTALLATION HINTS

3. Connect the cable to the corresponding terminals

according to the following instructions.

DESCRIPTION

Installation Instructions

SB200-001

HVAC Occupancy Sensor

OPERATION

Operation Diagram

A. Standby

After warm up period expires, the

sensor enters into standby mode.

Sensor will check if delay jumpers

are properly placed. If not, the LED

will flash.

B. Relay ON Delay

Relay ON delay is the time given

to sensor to verify true occupancy

before activating the relay output.

Any further detection during ON

delay will NOT reset the timer.

C. 1-minute Waiting

When Relay ON delay expires, the

sensor enters into a 1-minute

waiting time. If no detection within

1 minute, then sensor will return to

standby mode. If any detection

occurs, then relay output will be

activated and Relay OFF delay will

be started.

D. Relay OFF Delay

Relay OFF delay is the time of

relay activating. Every detection

during this period will reset the

timer.

RANGE ADJUSTMENT

In order to suit different rooms or areas, the detection range of

SB200-001 can be adjusted by changing the direction of the

sensor. To change the sensor direction, release the screw on

the mounting bracket and then carefully move the sensor to the

direction desired.

ON / OFF DELAY

The ON and OFF delays are designed to provide intelligent energy

management of the HVAC system. ON delay is the time given to

the sensor to certify the occupancy, before it activates the fan

controller. OFF delay is the time that relay is active. Both ON and

OFF delays can be easily set by placing the jumper on the

corresponding pins as follows:

DETECTION PATTERN

SPECIFICATIONS

Standby

Relay ON

Delay

1-Minute

Waiting

Relay OFF

Delay

(Relay Output)

A B C D E F

ON 0 sec. 10 sec. 30 sec. 1 min. 5 min. 10 min.

OFF 10 sec. 1 min. 5 min. 10 min. 20 min. 30 min.

•READ THESE INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS

DEVICE.

•Failure to observe safety information and comply with

instructions could result in PERSONAL INJURY, DEATH AND/

OR PROPERTY DAMAGE.

•To avoid electrical shock or damage to equipment, disconnect

power before installing or servicing.

•To avoid potential fire and/ or explosion do not use in potentially

flammable or explosive atmospheres.

•Retain these instructions for future reference. This product,

when installed, will be part of an engineered system whose

specifications and performance characteristics are not designed

or controlled by PECO, Inc. You must review your application

and national and local codes to assure that your installation

will be functional and safe.

WARNING

Use Copper wire only, insulate or wire nut

all un-used leads.

CAUTION

detection

Detection

Power supply…………...24 ± 2 V AC/DC

Detection range………..110°, 15 x 15 m at 25°C

Output format…………..Form C, 30 VDC, 0.2A max.

Current drain.................Standby: 5 mA Active: 18 mA

Mounting height…………1.8~3.6 m

Mounting bracket………..MB-99

Detectable speed………..0.1~3.0 m/sec.

RFI immunity…………….Av. 20 V/m (10~1,000 MHz)

Temperature…………….-20°C~38°C (-4°F ~ 100°F)

Humidity…......................95% RH max.

Dimensions.....................112 x 66 x 45 mm

Produkt Specifikationer

Mærke:	PECO
Kategori:	Termostat
Model:	SB200-001

Har du brug for hjælp?

Hvis du har brug for hjælp til PECO SB200-001 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat PECO Manualer

PECO TH109-009 Manual

15 August 2024

PECO T4522-001 Manual

15 August 2024

PECO SA200-001 Manual

15 August 2024

PECO TB155-046 Manual

12 August 2024

PECO TRF 115-007 Manual

11 August 2024

PECO SB200-001 Manual

10 August 2024

PECO T8532-001 Manual

10 August 2024

PECO TF115P-002 Manual

9 August 2024

PECO TF115-023 Manual

7 August 2024

PECO T12532-001 Manual

7 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Bticino NT4451 Manual

8 Oktober 2025

Bticino HS4451 Manual

7 Oktober 2025

Bticino N4451 Manual

7 Oktober 2025

Bticino L4451 Manual

7 Oktober 2025

Bticino AM5721 Manual

6 Oktober 2025

Bticino L4441FH Manual

6 Oktober 2025

Bticino Living 4477 Manual

6 Oktober 2025

Bticino HC4451 Manual

6 Oktober 2025

Emerson ST75 Manual

1 Oktober 2025

Homematic IP HMIP-eTRV Manual

30 September 2025