PECO SA200-001 Manual

PECO Termostat SA200-001

Læs gratis den danske manual til PECO SA200-001 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12 anmeldelser. Har du et spørgsmål om PECO SA200-001, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION & WALK TEST

Installation

1. Open the cover by loosening the screw. Bend the clip

and remove the PCB module.

2. Route the cable into the unit base and mount the base

on the ceiling.

3. Replace the PCB module. Connect the cable to the

corresponding terminals according to the following

instructions.

Wiring Diagram

NC-COM-NO: Output for ON-OFF control of fan

coil operation.

24 V: Power supply (non-polarity)

4. Replace the front cover and perform the walk

test.

DESCRIPTION

GENERAL

The SA200-001 is a ceiling mount 360° occupancy sensor

designed for automatic HVAC system control. This sensor

provides a changeover (form C) output for fan coil controller

to activate/deactivate the operation of fan coil automatically.

Apply power, allowing 25 seconds for sensor to warm up.

The LED will blink (long and short) during warm up period.

Ensure the jumper head connectors of ON & OFF delays

are placed at “A” position (shortest delay). After the warm

up expires, walk across the (invisible) detection zones at

normal pace. The LED will light whenever sensor detects

the motion. Note: The LED will blink if any jumper connector

is not properly placed.

Walk Test

Installation Instructions

SA200-001

HVAC Occupancy Sensor

OPERATION

Operation Diagram

A. Standby

After warm up period expires, the

sensor enters into standby mode.

Sensor will check if delay jumpers

are properly placed. If not, the LED

will flash.

B. Relay ON Delay

Relay ON delay is the time given

to sensor to verify true occupancy

before activating the relay output.

Any further detection during ON

delay will NOT reset the timer.

C. 1-minute Waiting

When Relay ON delay expires, the

sensor enters into a 1-minute

waiting time. If no detection within

1 minute, then sensor will return

to standby mode. If any detection

occurs, then relay output will be

activated and Relay OFF delay will

be started.

A. Relay OFF Delay

Relay OFF delay is the time of

relay activating. Every detection

during this period will reset the

timer.

ON / OFF DELAY

The ON and OFF delays are designed to provide intelligent energy

management of HVAC system. ON delay is the time given to the

sensor to certify the occupancy, before it activates the fan

controller. OFF delay is the time that relay is active. Both ON and

OFF delays can be easily set by placing the jumper on the

corresponding pins as follows:

DETECTION PATTERN

Standby

Relay ON

Delay

1-Minute

Waiting

Relay OFF

Delay

(Relay Output)

A B C D E F

ON 0 sec. 10 sec. 30 sec. 1 min. 5 min. 10 min.

OFF 10 sec. 1 min. 5 min. 10 min. 20 min. 30 min.

•READ THESE INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS

DEVICE.

•Failure to observe safety information and comply with

instructions could result in PERSONAL INJURY, DEATH AND/

OR PROPERTY DAMAGE.

•To avoid electrical shock or damage to equipment, disconnect

power before installing or servicing.

•To avoid potential fire and/ or explosion do not use in

potentially flammable or explosive atmospheres.

•Retain these instructions for future reference. This product,

when installed, will be part of an engineered system whose

specifications and performance characteristics are not

designed or controlled by PECO, Inc. You must review your

application and national and local codes to assure that your

installation will be functional and safe.

WARNING

Use Copper wire only, insulate or wire nut

all un-used leads.

CAUTION

detection

Detection

Infrared sensor ................. Dual element

Power supply .................... 24 ± 2 V AC/DC

Detection range ................ Height x 2.5 at 25°C

Output format ................... Form C, 30 VDC, 0.2A max.

Current drain .................... 5 mA @24 VAC

Mounting height ............... 2.4~4.2 m

Detectable speed ............. 0.1~3.0 m/sec.

RFI immunity ................... Av. 20 V/m (10~1,000 MHz)

Temperature ..................... -20°C~38°C (-4°F ~ 100°F)

Humidity ........................... 95% RH max.

Dimensions ...................... 110 (Dia.) x 44 (H) mm

SPECIFICATIONS

Top View 360°

Side View

Produkt Specifikationer

Mærke:	PECO
Kategori:	Termostat
Model:	SA200-001

Har du brug for hjælp?

Hvis du har brug for hjælp til PECO SA200-001 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat PECO Manualer

PECO TH109-009 Manual

15 August 2024

PECO T4522-001 Manual

15 August 2024

PECO SA200-001 Manual

15 August 2024

PECO TB155-046 Manual

12 August 2024

PECO TRF 115-007 Manual

11 August 2024

PECO SB200-001 Manual

10 August 2024

PECO T8532-001 Manual

10 August 2024

PECO TF115P-002 Manual

9 August 2024

PECO TF115-023 Manual

7 August 2024

PECO T12532-001 Manual

7 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Bticino NT4451 Manual

8 Oktober 2025

Bticino HS4451 Manual

7 Oktober 2025

Bticino N4451 Manual

7 Oktober 2025

Bticino L4451 Manual

7 Oktober 2025

Bticino AM5721 Manual

6 Oktober 2025

Bticino L4441FH Manual

6 Oktober 2025

Bticino Living 4477 Manual

6 Oktober 2025

Bticino HC4451 Manual

6 Oktober 2025

Emerson ST75 Manual

1 Oktober 2025

Homematic IP HMIP-eTRV Manual

30 September 2025