Phanteks Eclipse G500A DRGB Manual

Phanteks Computerbehuizing Eclipse G500A DRGB

Læs gratis den danske manual til Phanteks Eclipse G500A DRGB (2 sider) i kategorien Computerbehuizing. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Phanteks Eclipse G500A DRGB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

| www.phanteks.com

INSTALLATION GUIDE

VERSION 1.0

INSTALLATION GUIDE

| www.phanteks.com

04 01

up to 360

INSTRUCTIONS

Thank you for choosing Phanteks. This manual will guide you

through the installation process of the Eclipse G500A chassis. If

you have any questions, please contact us through our customer

service or social media.

This manual is for the following models:

PH-EC500GA_DBK01A

PH-EC500GA_DMW01A

PH-EC500GA_BBK01

PH-EC500GA_DBK01B

D-RGB Satin Black

D-RGB Matte White

Performance

D-RGB Fanless

3x 140mm D-RGB Fans Black

3x 140mm D-RGB Fans White

4x 140mm Fans Black

No Fans

Phanteks will not take responsibility for any damages incurred due to incorrect

installation or usage of this product.

G500A | D-RGB

G500A | PERFORMANCE & D-RGB FANLESS

SSD + MOTHERBOARD

SCREW

22X

STANDOFF REMOVAL

TOOL

MOTHERBOARD

STAND-OFF

PSU SCREW

THUMB SCREW

12x

FAN SCREW

RISER CABLE SCREW

CASE SCREW

M25-140MM FAN

depending on model

ANTI-SAG BRACKET

VERTICAL GPU MOUNT

ZIP TIE

2.5” SSD BRACKET

3x pre-installed

3.5” HDD BRACKET

2x pre-installed

FRONT TOP REAR CLEARANCEFANS

RADIATOR

120mm

up to 360

3x 1x

up to 120

up to 420

up to 280

up to 140

140mm

CPU Cooler Height

GPU Length

Power Supply

Front Panel Fan

Front 360 Radiator

Top 360 Radiator

Front 420 Radiator

185 mm

435 mm

250 mm 195mm If all 4 bottom HDD positions used

33 mm Behind front panel

95 mm

70 mm

142 x 475 mm

MODES COLORS

Press and hold the button for two seconds to turn MODE

off LEDs, press again to turn it ON

NOTE | D-RGB control buttons are deactivated when connected to a motherboard.

SOLID

BREATHING

SPARKLE

MUTLI-COLOR

TURN OFF LEDs

HDD LOCKING SCREW

RESET BUTTON

USB C 3.1

POWER BUTTON

USB 3.0

AUDIO / MIC

MODE BUTTON

COLOR BUTTON

USB C 3.1

USB 3.0

AUDIO / MIC

INCLUDED VERTICAL GPU MOUNT

GEN 4 RISER CABLE SOLD SEPARATELY PH-CBRS4.0_FL22

OPTIONAL UPGRADE

GEN 4 VERTICAL GPU BRACKET PH-VGPUKT4.0_03 (GEN 4.0 RISER CABLE INCLUDED)

The G500A chassis supports the placement of a vertical GPU with the included vertical GPU mount. The Vertical GPU mount has two

mounting positions, A or B as seen at step 03.

As an alternative, the supports the Phanteks Vertical GPU Bracket which supports up to a 4 slots GPU. Also this bracket puts G500A

the GPU further away from the tempered glass panel for increased airflow.

OPTIONAL UPGRADE

PSU SCREW

INSTALL

Insert the thumbscrews without tightening

them.

Manually press down the screws , then (1)

lock the thumbscrews in position .(2)

Make sure to install all GPU & PCI cards

beforehand. Place the GPU anti-sag

bracket at the back. For easy access,

remove the SSD bracket first.

THUMB SCREW

INSTALL

INCLUDED ACCESSORIES FRONT I/O

D-RGB CONTROLS

FAN & RADIATOR SUPPORT

ANTI-SAG BRACKET

01 02 03

A B

Connect the riser cable to the

vertical GPU mount and secure it

with 2x long riser cable screws.

Secure the Vertical GPU mount on

the chassis with 2x PSU screws.

Position A can hold 3-slot

GPU cards.

Position B can hold 2-slot

GPU cards.

RISER CABLE

SCREWS

INSTALL

Only applicable for the following models:

PH-EC500GA_DBK01A PH-EC500GA_DMW01A &

INSTALLATION GUIDE

VERSION 1.0

INSTALLATION GUIDE

| www.phanteks.com

INSTALLATION GUIDE

| www.phanteks.com

LEFT SIDE PANEL

MOTHERBOARD POWERSUPPLY

STORAGE 2.5” SSD|

STORAGE 3.5” HDD|

RIGHT SIDE PANEL

FRONT PANEL & DUST FILTERS

It is recommended to remove all external panels before starting the installation process. The G500A comes with storage cover panels

that are behind the right side panel, these support up to 6x 2.5” SSDs next to the 3x 2.5” SSD pre-installed brackets.

Open the left side panel and lift upwards

to remove it.

Remove the front panel by pulling the panel from below towards

you. The top filter can also be remove by pulling it upwards at

the rear. The PSU filter can be removed by sliding it outwards.

Install the ATX motherboard using 9x motherboard screws. For

M-ATX Motherboards follow the motherboard instructions to

move the stand-offs to the correct position. Use the ‘stand-off

removal tool’ when using a smaller motherboard.

(01) Remove the PSU bracket first by loosing the 2x thumb

screws. (02) Install the power supply with 4x PSU screws onto the

bracket. (03) Place it back into the chassis and tighten the 2x

thumb screws.

Open the right side panel and lift upwards

to remove it.

Slide the SSD Bracket up to remove it from

the chassis.

Slide the 3.5” HDD into the HDD cage. When installing 2x 3.5” HDD

brackets, stack them first before placing it into the chassis.

Slide the HDD bracket in, then press it

down to secure it.

To lock the HDD bracket, use 2x Thumb

screws per bracket.

Remove the HDD thumb screw to remove

the cable cover(s) on the inside of the

chassis.

Slide the HDD bracket into the bottom part of the chassis, make

sure they click when installed to be sure it is installed correctly.

Secure the SSD with 4x SSD screws to the

SSD Bracket.

For even more storage, secure the SSD with

4x SSD screws directly onto the panels.

Connect the front I/O cables to the motherboard and power

supply.

More D-RGB lighting products can be connected to the integrated

D-RGB controller. Optionally, lighting can be connected and

controlled via motherboard software.

MOTHERBOARD HEADER

MOTHERBOARD FRONT I/O EXPAND WITH MORE D-RGB PRODUCTS SYNC LIGHTING TO THE MOTHERBOARD

SLIDE UP TO

REMOVE

SLIDE DOWN TO

INSTALL

THUMBSCREW

LOOSEN

THUMB SCREW

REMOVE

MOTHERBOARD

SCREWS

INSTALL

PSU SCREW

INSTALL

THUMB SCREW

INSTALL

PANEL REMOVAL

HARDWARE INSTALLATION

CABLES D-RGB CABLES

A B

02 03

PRO TIP

FRONT FAN BRACKETS

The front fan brackets can

be secured in the 120mm fan

position by 6x screws.

Out of the box the brackets

are set to 140mm position.

CASE SCREW

REMOVE

SSD SCREW

INSTALL

SSD SCREW

INSTALL

PRESS DOWN TO

REMOVE BRACKET

SECURE BRACKET

3.5” HDD

2.5” SSD

STACK TOGETHER AND

SLIDE BACK TO LOCK

GRAB AND PULL

TOWARDS YOU

PSU

01 02 03

120MM 140MM

PSU FILTER

COVER PANELS

To access the storage space, push down

the clips on each cover panel to release it.

REMOVE SIDE PANEL BY

LIFTING IT UPWARDS

POWER_SW

SSD CAP*

REMOVE

*WHITE MODEL ONLY

PULL UPWARDS

TOP FILTER

FRONT FILTER

Only applicable for the following models:

PH-EC500GA_DBK01A PH-EC500GA_DMW01A , &

PH-EC500GA_DBK01B

Produkt Specifikationer

Mærke:	Phanteks
Kategori:	Computerbehuizing
Model:	Eclipse G500A DRGB
Type:	PC
Bredde:	240 mm
Dybde:	500 mm
Højde:	515 mm
Vægt:	10680 g
Velegnet til:	Spil
Produktfarve:	Sort
Pakkevægt:	12700 g
Pakkedybde:	610 mm
Pakkebredde:	325 mm
Pakkehøjde:	610 mm
Formfaktor:	Midi Tower
Antal USB 3.2 Gen 1 (3.1 Gen 1) type-A-porte:	2
Materiale:	Steel, Tempered glass
Lydindgang:	Ja
Belysning:	Ja
Belysningsfarve:	Flere
Lydudgang:	Ja
Strømforsyning inkluderet:	Ingen
Tænd/sluk-knap:	Ja
Forbedret kabelstyring:	Ja
Antal 3.5" bays:	10
Understøttet motherboard, formfaktorer:	ATX, EATX, Micro ATX, Mini-ITX
Antal 2.5" bays:	9
Siderude:	Ja
Antal udvidelsesporte:	7
Maksimal højde på CPU-køler:	185 mm
Maksimal længde på grafikkort:	435 mm
Maksimal PSU længde:	250 mm
Understøttede HDD-størrelser:	2.5, 3.5 "
Placering af strømforsyning:	Bund
Frontventiler installeret:	3x 120 mm
Antal understøttede frontventilatorer (maks.):	3
Understøttede diametre for frontventilatorer:	120,140 mm
Antal understøttede bagerste ventilatorer (maks.):	1
Understøttede diametre for bagerste ventilatorer:	120,140 mm
Antal understøttede øverste ventilatorer (maks.):	3
Understøttede diametre for øverste ventilatorer:	120,140 mm
Hærdet (ede) glaspanel (er):	Ja
Antal USB 3.2 Gen 2 (3.1 Gen 2) type-C-porte:	1
Anti-støvfilter:	Ja
RGB-kontrolknap:	Ja
Understøttede størrelser på frontradiator:	360,420 mm
Understøttede størrelser på bagradiator:	120 mm
De mest almindelige radiatorstørrelser understøttes:	280,360 mm