Phanteks Glacier C350i Manual

Phanteks Ikke kategoriseret Glacier C350i

Læs gratis den danske manual til Phanteks Glacier C350i (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Phanteks Glacier C350i, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Phanteks Glacier C350i

INSTALLATION GUIDE

PACKAGE CONTENTS

Glacier C350i

QTY: 1

RGB LED Cable

QTY: 1

DISCLAIMER - This product is intended for advanced users. Please consult with a

sive information possible, Phanteks assumes no liability expressed or implied for

any damage(s) occurring to your components as a result of using Phanteks cooling

products, either due to mistake or omission on our part in the below instructions,

or due to failure or defect in the Phanteks cooling products.

WARNING

electric charge by touching a grounded surface – for example, the metal surface of

the power supply or chassis – before performing any hardware procedure. Phanteks

assumes no liability for any damage, caused directly or indirectly, by improper

installation of any components. If you do not feel comfortable with performing the

Thermal Compound

(PH-NDC_01)

QTY: 1

Intel LGA 2011-3 Socket Screws

QTY: 4

Intel LGA 775/115X/1366

Socket Screws, Black Studs

QTY: 4 each

Phanteks Back Plate

QTY: 1

Phanteks Manual

QTY: 1

Phanteks Motherboard RGB Adapter

QTY: 1

RGB Y-Splitter

QTY: 1

*Please do not disassemble the water block. Warranty will be voided.

STEP 1: CONNECTING THE RGB LED LIGHTING

FOR INSTALLATION OF LGA 775/115X/1366

STEP 2: SETTING UP THE BACK PLATE

Please verify that all four screws are inserted correctly.

Plug in the connectors of the RGB LED Cable as illustrated.

*After mounting the C350i on your motherboard:

Two options to install the RGB lighting from the C350I block

A. Connect to a compatible Phanteks Case (see Phanteks.com for compatibility)

B. Connect to a compatible motherboard featuring a RGB header, using the RGB.

(see Phanteks.com for compatibility)

A. CONNECT TO COMPATIBLE PHANTEKS CASE

B. CONNECT TO COMPATIBLE MOTHERBOARD

PHANTEKS CASE

RGB LED ADAPTER

To make sure you choose the correct position, please take a look at the mounting

bracket. Choose the correct position by the numbers indicated on the bracket for

your motherboard CPU socket.

Position 1: LGA 1366

Postion 2 :LGA 115x

Position 3: LGA 775

Insert the four (4) screws into the correct position

indicated on the mounting bracket.

STEP 4: INSTALLING THE STUDS

STEP 5: APPLYING THERMAL PASTE

Remove any residual traces of thermal paste or thermal pads on your CPU before you add the

new PH-NDC thermal paste. It is recommended to use a 70- to 90-percent isopropyl alcohol

when removing thermal grease. While holding the chip by its sides, gently rub the thermal

removed, use a small amount (4-5mm diameter) of the PH-NDC and apply to the center of

the CPU surface.

STEP 6: INSTALLING THE C350i TO THE BRACKET

Do not use force to overturn the screw, please stop when the screw is at a natural stop.

With the C350i’s design, the CPU block can be installed in both orientation (horizontally/ver-

STEP 3: SETTING UP THE BACK PLATE (cont.)

Place the back plate on the rear side of the motherboard, so that the socket screws will stick

through the socket mounting holes. Please see image for reference.

Place the four (4) included studs onto the socket screws.

Insert the four (4) socket screws (Intel LGA 2011-3 Socket Screws) directly into the

motherboard.

INTEL LGA 2011-3 INSTALLATION

For instruction on how to apply the thermal paste, please see Installation of LGA

775/115X/1366, Step 5.

C350i on top of the CPU and tighten the screws.

Do not use force to overturn the screw, please stop when the screw is at a natural stop.

STEP 1: INSTALLING THE SOCKET SCREWS TO THE MOTHERBOARD

STEP 2: SECURING THE SOCKET SCREWS TO THE C350I

STEP TWO: SECURE THE BACK PLATE

Insert the four (4) screws into the correct LGA slot position indicated on the mounting

bracket. Make sure that the head of the screw is inserted correctly, you can see the diagram

for reference in Step One.

Place the back plate on the rear side of the motherboard, so that the socket screws will stick

through the socket mounting holes. Please see image for reference.

Produkt Specifikationer

Mærke:	Phanteks
Kategori:	Ikke kategoriseret
Model:	Glacier C350i
Type:	Vandblok
Bredde:	90 mm
Dybde:	90 mm
Højde:	35 mm
Vægt:	200 g
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Pakkevægt:	650 g
Pakkedybde:	135 mm
Pakkebredde:	135 mm
Pakkehøjde:	65 mm
Passende til rumtype:	Processor
Understøttede procesorsokler:	LGA 1151 (Socket H4), LGA 2011-v3 (Socket R)
Installationsvejledning:	Ja
Vandblokerende materiale:	Kobber
CPU-beslag:	Ja