Planet GSD-2022P Manual

Planet Skifte GSD-2022P

Læs gratis den danske manual til Planet GSD-2022P (2 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Planet GSD-2022P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 16-Port 10/100/1000T 802.3at PoE+

Ethernet Switch, GSD-2022P. mentioned in “802.3at PoE+ Switch”

this Guide refers to the GSD-2022P.

Open the box of the 802.3at PoE+ Switch and carefully unpack it. The

box should contain the following items:

The 802.3at PoE+ Switch x 1 User’s Manual x 1 Power Cord x 1

SFP Dust Cap

x 2 Screws x 8 Rack-mounting

Brackets x 2 Rubber Feet x 4

If any of these pieces are missing or damaged, please contact your

dealer immediately; if possible, retain the carton including the original

packing material, and use them again to repack the product in case

there is a need to return it to us for repair.

 Hardware-based DIP switch for or mode Standard, VLAN Extend

selection;

− VLANmode:Ports1to16cannotcommunicatewitheachother,

but can communicate with the uplink ports 17 to 18 and SFP

ports 19 to 20

− Extend mode: Ports 1 to 8 have data rate of 10Mbps. The

farthest transmission distance is up to 250 meters and all ports

can communicate with each other.

 VLAN mode is to isolate ports to prevent broadcast storm and

defendDHCPspoong

 Automatic address learning and address aging

 SupportsEnergy-EcientEthernet(EEE)function(IEEE802.3az)

 Hardware

 12-inchdesktopsize,1Uheight

 LED indicators for system power, per port PoE ready and PoE

activity,speed,Link/Act

 1silentfantoprovidestableandecientpowerperformance

 Supports contact dischargeof ±6KV DC and airdistance discharge

of±8KVDCforEthernetESDprotection

 Supports±6KVsurgeimmunity

3.ProductSpecications

Model GSD-2022P

HardwareSpecications

10/100/1000BASE-T

Copper Ports 18 auto MDI/MDIX

4.2 LED Indicators

 System

LED Color Function

PWR Green Lights to indicate the Switch has power.

 Per 10/100/1000BASE-T Port

LED Color Function

10/100/1000

LNK/ACT Green

Lights to indicate the link through that

port is successfully established.

Blinks to indicate that the Switch is

activelysendingorreceivingdataover

that port.

PoE in Use Amber Lightstoindicatetheportisproviding

PoE DC in-line power.

 Per 1000BASE-X SFP Interface

LED Color Function

1000

LNK/ACT Green

Lights to indicate the link through that port

is successfully established at 1000Mbps.

BlinkstoindicatethattheSwitchisactively

sendingorreceivingdataoverthatport.

Switch

Throughput@64bytes 29.76Mpps

MAC Address Table 8K entries

Jumbo Frame 9216 bytes

Flow Control IEEE 802.3x pause frame for full duplex;

back pressure for half duplex

PoweroverEthernet

PoE Standard IEEE802.3atPoweroverEthernetPlus/PSE

PoE Injector Ports 16

PoE Power Supply

Type

End-span/Mid-span:1/2/4/5(+),3/6/7/8

(-)

PoE Power Output

Perport54VDC,300mA.max.15.4watts

(IEEE802.3af)

Perport54VDC,600mA.max.32watts

(IEEE802.3at)

PoE Power Budget 185 watts

Number of PDs, 7

watts 16

Number of PDs, 15.4

watts 12

Number of PDs, 30

watts 6

Standards Conformance

Regulatory

Compliance FCC Part 15 Class A, CE

2. Product Features

 Physical Port

 16-port 10/100/1000BASE-T Gigabit RJ45 copper with IEEE

802.3at PoE+ injector function

 2 10/100/1000BASE-T Gigabit RJ45 copper interfaces

 2 1000BASE-X SFP slot interfaces

 PoweroverEthernet

 Complies with IEEE 802.3at Power over Ethernet Plus end-span

PSE

 Up to 16 ports of IEEE 802.3af/802.3at devices powered (ports

1~16)

 Supports PoE power up to 32 watts for each PoE port, with a total

PoE budget of 185W

 Eachportsupports54VDCpowertoPoEpowereddevice

 Autodetectspowereddevice(PD)

 SupportsPDalivefunction

 Circuitprotectionpreventspowerinterferencebetweenports

 Remote power feeding up to 100m in standard mode with 250m in

extend mode

 Switching

 Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/

MDI-X

 Supports IEEE802.3x ow control in full-duplex mode and back-

pressure in half-duplex mode

 Integrates address look-up engine, supporting 8K absolute MAC

addresses

 9Kjumboframesupportsallspeeds(10/100/1000Mbps)

1000BASE-X SFP

Slots 2

DIP Switch

Selectable operation mode

 Standard

 VLAN

 Extend

LED

 System:

Power(Green)

 10/100/1000T RJ45 Interfaces

10/100/1000LNK/ACT(Green),

PoE-in-Use(Amber)

 1000X SFP Interfaces

1000LNK/ACT(Green)

Dimensions

(WxDxH) 280x180x44mm(1Uheight)

Enclosure Metal

Weight 1810g

Power Requirements 100~240VAC,50/60Hz,5Amax.

Power Consumption/

Dissipation Max. 201 watts/686 BTU

Thermal Fan 1

ESD Protection Contactdischargeof±6KVDC,

Airdischargeof±8KVDC

Surge Protection ±6KV

Installation Desktop or rack-mount installation

Switching

Switch Architecture Store-and-Forward

Switch Fabric 40Gbps/non-blocking

Standards

Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE802.3zGigabitSX/LX

IEEE802.3xowcontrolandbackpressure

IEEE802.3afPoweroverEthernet

IEEE802.3atPoweroverEthernetPlus

IEEE802.3azEnergy-EcientEthernet

Environment

Operating

Temperature: 0 ~ 50 degrees C

RelativeHumidity:5~95%

(non-condensing)

Storage

Temperature: -10 ~ 70 degrees C

RelativeHumidity:5~95%

(non-condensing)

4. Hardware Introduction

4.1 Front Panel

The Front Panel of the 802.3at PoE+ Switch consists of 18 auto-sensing

10/100/1000Mbps Ethernet RJ45 ports and 2 1000BASE-X SFP slots.

The LED Indicators are also located on the front panel of the 802.3at

PoE+ Switch.

2 106 14 18 20

1 95 13 17 19

PoE Max

PWR

4 128 16

3 117 15

19 20

1000X SFP

Standard

VLAN

Ext end

PoE-in-Us e

LNK

ACT

Figure 4-1: GSD-2022P Switch Front Panel

4.3 Multiple Functions of DIP Switch

The front panelof the 802.3at PoE+Switch provides one DIP switchfor

Standard, VLAN or Extend mode selection. The detailed descriptions

are shown in the following table.

DIP Switch Mode Function

Standard

VLAN

Extend

This mode makes the 802.3at PoE+ Switch

operate as a general switch and all PoE

ports operate at 10/100/1000Mbps auto-

negotiation. All ports can communicate with

one another.

Standard

VLAN

Extend

This mode makes the 802.3at PoE+ Switch

operate as a switch andVLAN isolation

1. Ports1to16willisolaterespectively.

2. Ports 1 to 16 can only communicate with

ports17~18(uplinkports)andSFPports

19~20

Standard

VLAN

Extend

This mode makes the 802.3at PoE+ Switch

operate as a Long Reach PoE switch and

1. Ports 1 to 8 support farthest transmission

distance of up to 250 meters

2. Ports1to8haveadatarateof10Mbps

3. All ports can communicate with one

another.

Note

Please adjust the DIP switch before powering on the

802.3at PoE+ Switch.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

Standard Mode (default)

Power

PoE IP Camera

PoE

100 meters (328 feet)

PoE

100BASE-TX UTP with PoE

GSD-2022P

Standard

VLAN

Extend

VLAN Isolation Mode

NVR

Ports 1 to 16

Access Denied

PoE

100BASE-TX UTP with PoE

GSD-2022P

IP Camera

Ports 17~18 and SFP Ports 19~20

to Ports 1~16 Access Permitted

1000BASE-T UTP

Standard

VLAN

Extend

Extend Mode

Ports 1 to 8

Power

250 meters (820 feet)

PoE

10BASE-T UTP with PoE

PoE IP Camera

GSD-2022P

Standard

VLAN

Extend

5. Hardware Installation

5.1 Rack Mounting

To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the

instructions described below.

Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with

the front panel positioned towards your front side.

Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+

Switch with supplied screws attached to the package. Figure

5-1 shows how to attach brackets to one side of the 802.3at

PoE+ Switch.

210

614 18 20

513 17 19

PoE Max

PW R

4 12

816

311

715

19 20

100

0X S FP

Standa rd

VLA N

tend

PoE-in-Use

LNK

ACT

Figure 5-1: Attaching the Brackets to the 802.3at PoE+ Switch.

Caution

You must use the screws supplied with the mounting

brackets. Damage caused to the parts by using incorrect

screwswouldinvalidatethewarranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second bracket to the

opposite side.

4.4 Rear Panel

The rear panel of the 802.3at PoE+ Switch indicates an AC power

socket,whichacceptsinputpowerfrom100to240VAC,50-60Hz,5A.

50/60Hz

100-240V , 5A max.

Figure 4-2: GSD-2022P Switch Rear Panel

 AC Power Receptacle

Power

Notice

The device is a power-required device, which means

it will not work till it is powered. If your networks

should be active all the time, please consider using UPS

(Uninterrupted Power Supply) for your device. It will

preventyoufromnetworkdatalossornetworkdowntime.

Power

Notice

In some areas, installing a surge suppression device may

also help to protect your 802.3at PoE+ Switch from being

damaged by unregulated surge or current to the 802.3at

PoE+ Switch or the power adapter.

Step 5: After the brackets are attached to the 802.3at PoE+ Switch,

use suitable screws to securely attach the brackets to the

rack, as shown in Figure 5-2.

2106 14 18

1 9

513 17

PoE Max

PW R

412

816

715

19 20

100

0X SFP

Stan dard

VLA N

Ext end Po E-in -Use

ACT

Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack

Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at

compliedPDsandothernetworkdevices.

A. Connect one end of a standard network cable to the

10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at

PoE+ Switch.

B. Connect theotherendof thecable tothenetworkdevices suchas

printerservers,workstationsorrouters,etc.

Step 7: Supply power to the 802.3at PoE+ Switch.

A. Connect one end of the power cable to the 802.3at PoE+ Switch.

B. Connect the power plug of the power cable to a standard wall

outlet.

When the 802.3at PoE+ Switch receives power, the power LED should

remain solid Green.

5.2 Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP slot

of the 802.3at PoE+ Switch.

TheSFPtransceiversarehot-pluggableandhot-swappable.Youcanplug

inandoutthetransceiverto/fromanySFPportwithouthaving topower

down the 802.3at PoE+ Switch, as the Figure 5-3 shows.

MGB-Series

SFP Transceiver

LC Fiber Cable

Figure 5-3: Plug In the SFP Transceiver

 Approved PLANET SFP Transceivers

PLANET 802.3at PoE+ Switch supports both single mode and multi-

mode SFP transceivers. The website link of approved PLANET SFP

transceiversisshownbelow:

https://www.planet.com.tw/en/product/mgb-series-transceiver

Note

It is recommended to use PLANET SFP on the 802.3at

PoE+ Switch. If you insert an SFP trans-ceiver that is not

supported,the802.3atPoE+Switchwillnotrecognizeit.

1. Before we connect the 802.3at PoE+ Switch to the other network

device, we haveto make sure bothsides ofthe SFP transceivers are

with the same media type, for example, 1000BASE-SX to 1000BASE-

SX; 1000BASE-LX to 1000BASE-LX.

2.Check whethertheber-optic cabletypematches withtheSFP trans-

ceiverrequirement.

To connect to 1000BASE-SX SFP transceiver, please use the

multi-mode ber cable with one side being the male duplex LC

connector type.

To connect to 1000BASE-LX SFP transceiver, please use the

single-mode ber cable with one side being the male duplex LC

connector type.

Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource on PLANET Web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET

support team.

PLANET online FAQs:

https://www.planet.com.tw/en/support/faq

Support team mail address

support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Produkt Specifikationer

Mærke:	Planet
Kategori:	Skifte
Model:	GSD-2022P

Har du brug for hjælp?

Hvis du har brug for hjælp til Planet GSD-2022P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Planet Manualer

Planet DCS-7342-32C2X Manual

8 Oktober 2024

Planet DCS-7342-48Y8C Manual

8 Oktober 2024

Planet GSD-1121XP Manual

18 September 2024

Planet BSP-115PV-15A Manual

7 September 2024

Planet BSP-115HP-5A Manual

5 September 2024

Planet IGTP-805AT Manual

3 September 2024

Planet IPM-16230 Manual

3 September 2024

Planet FSD-804P Manual

3 September 2024

Planet UPOE-1600G Manual

1 September 2024

Planet WS-1032P Manual

1 September 2024

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025